As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A gravel truck on the highway flicks up a stone, and by the time you park there is a small star in the glass. The permatex vs rain x windshield repair kit question usually starts right there, in the auto parts aisle, with two boxes that look like they do the same job. They both use a clear resin that fills the break and hardens in sunlight, yet they differ in how big a chip they accept, whether they claim to handle cracks and how they push resin into the glass.
We set the two kits side by side using what each maker publishes, then add a third chip kit from J-B Weld that works much like the Permatex. None of these replaces a glass shop for a long crack or damage in front of the driver, and we explain where that line sits.
Quick answer
Should you buy the Permatex or the Rain-X kit for a chip?
Choose Permatex 09103 for a bullseye or star up to 1-1/4 inches, since its spring-lock syringe sets the pressure for you. Choose Rain-X 600001 when the chip is under 1 inch or a crack shorter than 12 inches has started, because its listing covers both. Long or edge cracks need a glass shop.
Our Quick Picks
For the Permatex vs Rain-X decision, here are the two compared kits plus a related third pick, the J-B Weld Windshield Saver, a second chip kit with the same size rating as the Permatex.

Permatex 09103
Timed vacuum and pressure steps for a single chip.

Rain-X 600001
The only kit of the three that lists crack repair.

J-B Weld Windshield Saver
A compact second chip kit similar to the Permatex.
Two Ways to Push Resin into Glass
Every DIY windshield kit has to solve the same problem. A stone chip is a tiny cone of fractured glass filled with air, and resin will not soak in while that air is trapped. The kit has to pull the air out, force resin in, and then hold it there while sunlight cures it.
Permatex does this with a pedestal stuck over the chip and a syringe that clips into two locked positions. Its instruction sheet has you lock the plunger in the low notch for 10 minutes to draw a vacuum, then reseat it and lock the upper notch for at least 20 minutes to push resin in. Rain-X describes a repair device you press with light, even pressure, and warns that pushing too hard can lengthen a crack instead of filling it.
| Point | Permatex 09103 | Rain-X 600001 | J-B Weld 2100 |
|---|---|---|---|
| Largest chip listed | Bullseye up to 1-1/4 in. | Round damage below 1 in. | Up to 1-1/4 in. |
| Cracks | Not described | Shorter than 12 in. | Not described |
| Pressure method | Spring-lock syringe, two settings | Hand-pressed repair device | Pressure-lock pedestal and syringe |
| Repairs per box | One (0.75 ml resin) | Several, per the listing | One (0.025 fl oz) |
The table shows the trade-off in plain terms. Permatex accepts a slightly bigger chip and takes the guesswork out of pressure, while Rain-X stretches to short cracks and leaves resin over for another chip. Neither maker publishes a strength or clarity test you could compare, so treat the claims on the boxes as limits rather than results.
Measure the Damage Before You Pick a Box
Lay a coin over the break. A US quarter is just under 1 inch across, so a chip that hides completely under it falls inside the Rain-X limit, and one that peeks out a little may still suit the Permatex or J-B Weld size rating. Measure the whole break, including any short legs running out of a star, not only the pit in the middle.
Next, look at the type of damage. A bullseye is a round cone, a star has short legs, and a combination break has both. Once a leg has grown into a line, you are dealing with a crack, which only the Rain-X listing addresses.
Timing matters as much as size. The National Windshield Repair Division’s consumer information page sums it up neatly: repairing a chip prevents a crack, and repairing a crack prevents a replacement. Put a piece of clear packing tape over a fresh chip to keep washer fluid and road grime out until you can fix it.
Permatex vs Rain X Windshield Repair Kit: The Three Kits Up Close
Below are the two kits from the title and a third chip kit that shares the Permatex size rating. All three already appear in our wider roundup of windshield repair kits, and here they are compared head to head. Read the size and damage limits on each before you order.
Permatex 09103: Windshield Repair Kit with Spring-Lock Syringe for Chips up to 1-1/4 Inch

- Bullseye damage up to 1-1/4 inch
- Spring-lock syringe with two locked settings
- Sun-cured resin, no mixing
- Nine pieces for one complete repair
The 09103 is Permatex’s standard windshield kit, rated for bullseye damage up to 1-1/4 inches on most laminated windshields. It is also one of the kits in our windshield repair kit roundup, set here directly against Rain-X. The box holds a syringe and plunger, resin compound, adhesive disc, pedestal, curing strip, push pin, razor blade, alcohol towelette and photo instructions.
What sets it apart is the spring-lock syringe. You twist it into the pedestal, lock the plunger in the low notch for about 10 minutes so it pulls air out of the break, then reseat it and lock the upper notch for at least 20 minutes so resin is pushed in. Because the clip holds each position, you are not guessing how hard to press, and nothing needs mixing.
Permatex asks you to work in shade with the glass between 50 and 75 degrees Fahrenheit, then cure the resin in direct sun for about 15 minutes, or an hour or more under cloud. The resin tube holds 0.75 ml, enough for one chip, so a car with two chips needs two kits. The listing describes bullseye damage, not running cracks, so a break that has already grown a line falls outside what this kit promises.

Rain-X 600001: Windshield Repair Kit for Chips under 1 Inch and Cracks under 12 Inches

- Round damage below 1 inch
- Cracks shorter than 12 inches
- Curing strips, cures in direct sunlight
- Listed for multiple repairs
Rain-X is better known for glass treatments, and the 600001 is its resin kit for laminated windshields. It shares a spot with the Permatex in our broader kit guide, and this page weighs the two against each other. The listing covers round damage below 1 inch across and cracks shorter than 12 inches, working on the outer layer of glass.
Chips and cracks get different methods. For a chip, you set the repair device over the break and press with light, even pressure while the resin works in; Rain-X warns that pressing hard can extend a crack. For a crack, you run resin along the line, cover it with curing strips, move the car into direct sun and scrape off the excess once it hardens.
Two practical points favor this kit for some drivers. The listing says one box is good for multiple repairs, which helps when a windshield has picked up more than one chip in a season. It also asks you to fix damage as soon as possible, before dirt or water gets inside, and to avoid feeding resin too quickly, since air pockets weaken the bond. Its chip limit is smaller than the Permatex rating, so measure first.
J-B Weld 2100 Windshield Saver: Pressure-Lock Repair Kit for Chips and Stars up to 1-1/4 Inch

- Chips, stars and bullseyes
- Damage up to 1-1/4 inch
- Pressure-lock pedestal and syringe
- Clear, sun-activated acrylic resin
The 2100 Windshield Saver is the related third pick here: a second chip kit that matches the Permatex size rating. It also sits in our main windshield repair kit list, and we include it so you can compare a close alternative. J-B Weld lists it for bullseye, star and stone chip damage up to 1-1/4 inches on laminated windshields.
J-B Weld describes the system as patented, built around a pressure-lock controlled pedestal and syringe that draws existing air out of the break so the resin can fill the voids. The resin is a single-component acrylic, so there is nothing to mix, and it dries clear and cures with sunlight. The kit holds 0.025 fluid ounces of resin, a portion sized for one repair.
This kit makes sense if the Permatex is out of stock or you simply want a second small kit in the glovebox for the next stone. Like the Permatex, it is aimed at chips and stars rather than cracks, and its listing says it helps prevent damage from spreading. Clean, dry glass and the timing in the package directions matter more to the result than the brand on the box.
View J-B Weld Windshield Saver on Amazon

Matching the Kit to Your Chip or Crack
Most drivers only need one box, and the right one depends on what the stone left behind. The table below sorts common situations by the kit whose published limits fit best. If your damage lands in the last two rows, skip the kits entirely.
| Damage you see | Closer fit | Why |
|---|---|---|
| Fresh bullseye up to 1-1/4 in. | Permatex 09103 | Largest chip rating, preset pressure steps |
| Small chip plus a second chip elsewhere | Rain-X 600001 | Listing says one box covers multiple repairs |
| Short crack under 12 in., away from the edge | Rain-X 600001 | Only kit of the three that lists cracks |
| Star break you want to fix from the glovebox | J-B Weld 2100 | Small single-repair kit, chips and stars |
| Damage in the driver’s view or touching the edge | Glass shop | Beyond what consumer kits are meant to handle |
| Crack longer than 12 inches | Glass shop | Outside every listing here |
Whichever kit you choose, expect an improvement rather than invisible glass. Permatex’s own instructions note that a repair may not fully remove the blemish or permanently fill the pit. A good result is a chip that stops catching the light and, more importantly, stops spreading.

A repair kit is a quick weekend job, and the same applies to plastic that has gone yellow up front. If your lenses are hazy too, our guide to headlight restoration kits covers the sanding and clear-coat steps. Clean glass and clear lenses go together when the evenings get dark early.
Fixing a Chip During a Grand Rapids Winter
Cold weather is the hardest part of DIY glass repair in West Michigan. Permatex’s maker page asks for a windshield temperature between 50 and 75 degrees Fahrenheit while the resin goes in, and it wants the work done in shade. From December to March that usually means pulling the car into a garage and letting the glass warm up first.
Curing is the second hurdle. All three resins harden under ultraviolet light, and Permatex quotes 15 minutes in direct sun or at least an hour on a cloudy day. On a gray January afternoon, roll the car out, park it facing the brightest part of the sky, and give it extra time before you peel off the curing strip.

Temperature swings are what turn chips into cracks. A blast of hot defroster air on frozen glass, or hot water poured over ice, puts stress right at the damaged spot. A windshield de-icer spray is a gentler way to clear the glass, and if your defroster is weak or blows cold, our car heater repair team can track down the cause.
Salt trucks and sand spreaders throw plenty of grit, and that is where many winter chips come from. Our winter car maintenance checklist covers wipers, washer fluid and the rest of the cold-season basics. The same spray that chips glass also coats the underside of the car, which is why we also wrote about undercoating for road salt.
Where a DIY Kit Stops and a Glass Shop Starts
A windshield does more than keep the wind out. The National Windshield Repair Division points out that it is a major part of the airbag system and the roof support, so a weak repair in the wrong place is not just a cosmetic problem. Leave these cases to an auto glass specialist: damage directly in the driver’s line of sight, any crack that reaches the edge of the glass, a crack longer than the kit’s listed limit, or a break that goes through to the inner layer.

Repaired chips are also worth noticing when you shop for a used car. A windshield with several old repairs, fresh water stains on the carpet or a musty smell can point to leaks, and our article on how to tell if a car has flood damage explains what to look for inside the cabin. Our pre-purchase inspection covers the mechanical side before you sign.
Streaks across the repaired area can also come from worn blades rather than the resin. If the wipers chatter or skip after a repair, check them before blaming the kit, and our guide to winter wiper blades covers designs that stay flexible in the cold.
More Buying Guides
Frequently Asked Questions
Permatex windshield repair kit vs Rain-X: which is easier for a first-timer?
Permatex is more forgiving for a first repair, because its spring-lock syringe holds the vacuum and pressure settings for you and the steps are timed. Rain-X relies on a light, steady hand on its repair device. Whichever you buy, read the full instruction sheet before you open the resin.
Can the Rain-X kit fix a windshield crack?
Its listing covers cracks shorter than 12 inches on laminated windshields, using resin and curing strips cured in direct sunlight. Results on cracks depend on keeping the crack clean and dry. A crack that reaches the edge or sits in the driver’s view still belongs at a glass shop.
Will the chip disappear after the repair?
Usually not completely. A good repair makes the chip much less visible and stops it from spreading, but a faint outline of the impact point often remains. Permatex says plainly that its kit may not fully remove the blemish.
Can I use these kits outside in winter?
Not on frozen glass. Permatex asks for a windshield between 50 and 75 degrees Fahrenheit during the repair, so warm the car in a garage first. Then move it into daylight to cure, and allow extra time when the sky is overcast.
Want a second opinion on a chip, or on the defroster that keeps fogging the glass? Phone 456 AutoFix at 616-279-3832 on weekdays between 8am and 5pm, or send us a note through the contact page.
Busy during our hours? Our after-hours drop-off at 456 Carrier St NE in Grand Rapids lets you leave the car whenever it suits you.
