456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Shopping for the Best TPMS Sensors for Jeep Wrangler? Fit Notes and Picks

best tpms sensors for jeep wrangler: vibrant aerial view of farmlands and a rural road

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A Wrangler lives a rougher life than most daily drivers, and its tire pressure sensors feel it. The best TPMS sensors for Jeep Wrangler owners are the ones that match the model year’s part number and radio frequency, because a sensor that suits a 2010 JK will not talk to a 2022 JL.

This guide sorts six sensors by year range, explains when a factory part beats a programmable one, and covers what trail days and Michigan winters do to valve stems. For sensors on other vehicles, our general TPMS sensor guide covers the wider market.

Quick answer

Which TPMS sensor should a Jeep Wrangler get?

Start with your model year. The Schrader 29093 is listed for Wranglers from 2013 to 2021, the Mopar 68339096AB covers later JL builds, and an Autel MX-Sensor suits owners with an Autel tool or a second set of wheels. Check the part number on your old sensor, then confirm fit on Amazon.

Our Quick Picks

Three picks that cover most Wrangler owners: an OE-replacement set for 2013 to 2021 models, the factory Mopar part for later JL builds, and a universal set for owners with an Autel tool. All six sensors are reviewed below.

Schrader 29093 (5 Pack) product photo
2013 to 2021

Schrader 29093 (5 Pack)

5 pack · 433 MHz · snap-in rubber

OE-replacement sensors listed for Wrangler 2013 to 2021.

SuitsJK and earlier JL owners replacing a full set
View on Amazon →
Mopar 68339096AB product photo
Factory part

Mopar 68339096AB

1 sensor · Mopar OEM · 68339096AB

The genuine Mopar sensor number used on later JL builds.

SuitsOwners who want the factory part for one corner
View on Amazon →
Autel MX-Sensor (Set of 4) product photo
Any year, with a tool

Autel MX-Sensor (Set of 4)

4 pack · 315/433 MHz · rubber or metal

Blank sensors that program to your Wrangler's protocol.

SuitsOwners with an Autel tool or a second wheel set
View on Amazon →

Match the Sensor to Your Wrangler Year First

Jeep has changed Wrangler sensors more than once, and the listings below reflect three broad groups. Older JK models from about 2008 to 2012 use 315 MHz sensors under part numbers such as 56053036AA. Wranglers from 2013 into 2021 move to 433 MHz sensors, and the later JL generation uses a different 433 MHz sensor sold as Mopar 68339096AB.

Those year lines come from the sensor listings, not from a Jeep fit chart, and 2021 sits on the boundary. The surest check is the part number printed on one of your existing sensors, which a tire tech can read when the tire is off the rim. A TPMS tool can also read the sensor and show its frequency without unmounting anything.

  • Frequency: 315 MHz and 433 MHz sensors are not interchangeable unless the sensor is a universal programmable type that covers both.
  • Valve style: the factory-style picks here use rubber snap-in stems, while the Autel set ships with both rubber and metal stems.
  • Wheel count: four sensors cover the road wheels, and a fifth only matters if your Wrangler’s spare carries one. Check before you buy a five-pack for that reason.

OE, Pre-Programmed or Programmable: Which Route Suits Your Jeep

A factory or OE-replacement sensor, such as the Mopar or Schrader parts below, arrives ready for one protocol and carries its own new ID. A pre-programmed aftermarket sensor behaves the same way, though it cannot be rewritten later. Either way, the Jeep has to learn the new IDs after installation.

A universal programmable sensor ships blank and is written with a tool to the Wrangler protocol. Its advantage is cloning: the tool copies your old sensor IDs onto the new ones, so the Jeep sees no change. That suits owners who run a separate set of trail or winter wheels.

Some Wranglers learn new IDs after a short drive, while others need a TPMS tool connected to the OBD2 port. Follow the procedure in your owner’s manual or the sensor maker’s instructions. If you are shopping for a scanner that can do it, our OBD2 scanner guide for DIY mechanics explains which tool types include TPMS service.

Best TPMS Sensors for Jeep Wrangler, Sorted by Year

The six sensors run from the 2013 to 2021 range, through later JL builds, to older JK models and one universal set. Year ranges are as each listing states them, so enter your Wrangler’s year, trim and engine on Amazon before ordering.

1. Schrader 29093: 433 MHz OE-Replacement Sensor, 5 Pack with Snap-In Valves

Schrader 29093 (5 Pack) product photo
Key features
  • 433 MHz, rubber snap-in fixed-angle valve
  • Listed for Wrangler 2013 to 2021
  • Also listed for Gladiator 2019 to 2021
  • Five sensors in Schrader boxes

The Schrader 29093 is an OE-replacement sensor sold here as a five-pack, each one boxed separately. It runs on 433 MHz and uses a rubber snap-in valve with a fixed angle, the same layout most factory Wrangler wheels were built around. The listing names Wrangler models from 2013 to 2021 and the Gladiator from 2019 to 2021.

That year span takes in later JK models and the first JL years, which makes it a broad fit for the 433 MHz era. Schrader points to the product description for exact fitment, so read that list against your year and trim rather than relying on the title alone. The fifth sensor can cover a monitored spare if your Jeep has one, or sit on the shelf for the next failure.

Schrader recommends professional installation and says the job needs a compatible tool with current software. In practice, that means a tire shop mounts the sensors with fresh valve hardware, then the Jeep learns the new IDs through its relearn routine or a TPMS tool. For an owner whose original sensors are ageing out at the same time, a full set in one order keeps every corner on the same part.

View Schrader 29093 (5 Pack) on Amazon

2. Mopar 68339096AB: Genuine OEM Tire Pressure Sensor

Mopar 68339096AB product photo
Key features
  • Genuine Mopar part 68339096AB
  • Built to factory fit, form and function
  • Sold as a single sensor
  • Cross-referenced to 2021 and later JL

The Mopar 68339096AB is the factory tire pressure sensor sold under Jeep’s own parts brand. The listing is brief: it gives the part number and states that the sensor is made to meet specifications for fit, form and function. It is sold one sensor at a time, which suits an owner replacing a single damaged unit.

Mopar’s page here does not print a fit list, so the year range comes from cross-references. Several aftermarket listings, including the VELDUROVEL set below, name 68339096AB as the original part for Wrangler and Gladiator models from 2021 onward. Compare that number with the one on your current sensor, or ask a dealer parts counter to confirm it against your VIN before ordering.

The main reason to pick a genuine part is certainty: it is the same design the Jeep left the factory with, so there is no question about protocol or frequency. A new OE sensor still carries a new ID, so the Jeep has to learn it after the tire goes back on. A shop with a TPMS tool can handle that step, or you can follow the procedure in your owner’s manual.

View Mopar 68339096AB on Amazon

picturesque countryside road meandering through lush green fields under a cloudy sky

3. Schrader 29244: 433 MHz Snap-In OE-Replacement Sensor, 4 Pack

Schrader 29244 (4 Pack) product photo
Key features
  • 433 MHz, rubber snap-in fixed-angle valve
  • Listed for select Wrangler and Gladiator models
  • Built to OE quality and performance standards
  • Relearn needs a TPMS tool with OBD access

The Schrader 29244 is a newer OE-replacement sensor, sold as a set of four with rubber snap-in valves at a fixed angle. It runs on 433 MHz, and the listing names select Jeep Gladiator, Grand Cherokee, Wagoneer and Wrangler models, plus the Alfa Romeo Tonale. That wording means it fits some Wranglers, not all of them, so the year check matters more here than anywhere else.

Schrader states that its OE-replacement sensors meet original equipment quality and performance standards, and that they go through high speed and extreme temperature testing. That is a useful point for a Jeep that sees summer highway trips and January cold starts. The design is a direct replacement rather than a programmable universal part, so there is nothing to write before installation.

The listing is clear that this is not a DIY product. A vehicle-specific relearn is required after installation, and Schrader says it needs a TPMS programming and diagnostic tool with OBD capability. For most owners, the practical route is to bring the set to a shop that has that tool. Confirm your year and trim against the listing’s fit details before you order.

View Schrader 29244 (4 Pack) on Amazon

4. Autel MX-Sensor: 315/433 MHz Programmable Sensors, Set of 4 with Rubber and Metal Valves

Autel MX-Sensor (Set of 4) product photo
Key features
  • Dual 315 MHz and 433 MHz, programmable
  • Interchangeable rubber and metal valves
  • Can clone original sensor IDs
  • Programs only with Autel TPMS tools

The Autel MX-Sensor is a universal programmable sensor, sold here as a set of four. It covers both 315 MHz and 433 MHz once programmed, so the same part can serve an older JK on 315 MHz or a newer JL on 433 MHz. The set comes with interchangeable rubber and metal valve stems.

The main strength is cloning. With a compatible Autel tool, you copy the old sensor IDs onto the new ones, and Autel says no relearn is needed when each clone goes in the same position. That suits Wrangler owners who run a separate set of trail or winter wheels, since both sets can carry the same IDs. Autel also says the sensor is tested to the SAE J1205 and J1206 standards.

The catch is the tool. Autel states that the MX-Sensor can only be programmed with Autel TPMS tools, such as the TS408S, TS508WF or ITS600, so check what your shop uses before ordering. The metal stem option helps on aftermarket off-road wheels with thicker valve holes. If you do not own an Autel tool and only need one corner replaced, a direct-fit sensor is the simpler route.

View Autel MX-Sensor (Set of 4) on Amazon

close-up of vintage filament light bulbs

5. VELDUROVEL 433 MHz Pre-Programmed Sensors: 4 Pack for 2021 to 2024 Wrangler

VELDUROVEL 68339096AB (4 Pack) product photo
Key features
  • 433 MHz, pre-programmed
  • Listed for Wrangler and Gladiator 2021 to 2024
  • Replaces OE 68339096AB and 68339096AA
  • Not reprogrammable

The VELDUROVEL set is a four-pack of pre-programmed 433 MHz sensors for later Jeep models. The listing names the Wrangler, Gladiator and Grand Cherokee L from 2021 to 2024, and it gives the original part numbers it replaces as 68339096AB and 68339096AA. That cross-reference is the same factory number as the Mopar sensor above.

Pre-programmed means the sensors arrive already set for the vehicle protocol, and the maker states they cannot be reprogrammed. There is nothing to write before installation, but you also cannot clone your old IDs onto them later. The listing says a reset is still mandatory after installation, and that a dedicated TPMS scanner or OBD diagnostic tool may be needed to finish it, depending on the model.

The listing also asks buyers to use Amazon’s fit check and to match the OE part code and frequency against the original sensors. That is good advice for a JL near the 2021 boundary. This set suits an owner who wants all four sensors replaced at once and has access to a shop or tool for the relearn. It does not suit anyone planning to clone IDs for a second wheel set.

View VELDUROVEL 68339096AB (4 Pack) on Amazon

6. X AUTOHAUX 56053036AA: 315 MHz Sensors, 4 Pack for 2008 to 2012 Wrangler

X AUTOHAUX 56053036AA (4 Pack) product photo
Key features
  • 315 MHz
  • Listed for Wrangler Rubicon and Sahara 3.8, 2008 to 2012
  • Cross-references 56053036AA and related numbers
  • Four sensors per pack

The X AUTOHAUX set covers the older end of the Wrangler range. It is a four-pack of 315 MHz sensors listed under part number 56053036AA, along with several related Chrysler numbers such as 68406530AA and 56029465AA. The fit list names the Wrangler Rubicon and Sahara with the 3.8 engine from 2008 to 2012.

That listing wording matters. It names those two trims rather than every early JK, so an owner with a different trim should read the full fit list and compare the part number on the old sensor before ordering. The same sensor also appears in the listing for several other Chrysler, Dodge and Jeep models of that period, including the Liberty, Compass and Patriot.

Sensors from those years are getting old, and an original sensor whose internal battery has run down is a common reason the warning stays on. This set replaces all four at once, which saves repeat trips as the remaining originals fail. The listing gives no programming or relearn details, so plan for a shop with a TPMS tool to finish the job after mounting. Ask for new valve hardware at the same visit.

View X AUTOHAUX 56053036AA (4 Pack) on Amazon

Wrangler TPMS Fit Chart

Use this chart as a starting point, then match it against the part number on your current sensor. The years here come straight from the Amazon listings reviewed above.

Wrangler years (as listed)FrequencySensors in this guide
2008 to 2012 (3.8 Rubicon, Sahara)315 MHzX AUTOHAUX 56053036AA, Autel MX-Sensor
2013 to 2021433 MHzSchrader 29093, Autel MX-Sensor
2021 to 2024 JL433 MHzMopar 68339096AB, VELDUROVEL, Autel MX-Sensor
Select later Wrangler models433 MHzSchrader 29244 (confirm years on the listing)
Jeep Wrangler TPMS sensors grouped by the year ranges their listings give
scenic view of curved roadway between green plantations with trees against mount and houses in countryside

Where two rows overlap, as they do around 2021, the part number on the old sensor decides it. When in doubt, a dealer parts counter can look up the sensor by your VIN.

Trail Days, Road Salt and Potholes

Airing down for a trail run will light the warning on almost any Wrangler, and that is the system doing its job. Air back up to the pressure on the door jamb sticker before the highway, not the maximum molded on the sidewall. The fueleconomy.gov maintenance tips also note that each psi of underinflation across the tires trims gas mileage, which a thirsty Jeep can do without.

scenic aerial view of rural landscape with fields and a country road

Grand Rapids winters add road salt, and salt is hard on the joint between a valve stem, its nut and its cap. Ask for a new service kit (grommet, nut, core and cap) whenever a tire comes off, and keep caps on all winter. Deep freeze-thaw potholes are the other threat, since a hard hit can crack a sensor body or bend a rim, and our guide to pothole damage signs shows what else to check.

When the Light Points Past the Sensor

A solid warning with correct pressures usually means a sensor that will not report, often from a flat battery in an older unit. A flashing light that then stays on tends to point to a system fault, and a TPMS tool that reads each sensor’s ID and status will narrow it down.

stunning aerial view of a rural road cutting through lush green fields

Sometimes the tires are only part of the story. Lifted Wranglers on bigger tires can wear steering and suspension parts faster, and the signs include wander on the highway, uneven tread wear or a shake after a bump. Our suspension and steering repair in Grand Rapids covers that inspection.

Frequently Asked Questions

Is a Jeep Wrangler TPMS sensor 315 MHz or 433 MHz?

It depends on the year. The listings in this guide put 2008 to 2012 Wranglers on 315 MHz and 2013 and later models on 433 MHz. Read the part number on your existing sensor or scan it with a TPMS tool to be sure.

Will my Wrangler learn new TPMS sensors by itself?

Some will after a drive, and some need a TPMS tool plugged into the OBD2 port. Pre-programmed sensors carry new IDs, so the Jeep must learn them either way. Follow the procedure in your owner’s manual or the sensor maker’s instructions.

Are aftermarket sensors among the best TPMS sensors for Jeep Wrangler use?

They can be, as long as the part number and frequency match your year. Schrader sells OE-replacement sensors for several Wrangler ranges, and a universal programmable sensor such as the Autel MX-Sensor can clone your old IDs. Budget pre-programmed packs work too, but they cannot be reprogrammed later.

Why does my Wrangler TPMS light come on after airing down?

The system warns when pressure falls well below the door placard value, and trail pressures are far below it. The light should clear once you air back up and drive. If it stays on at correct pressures, a sensor may have been damaged on the trail.

Wrangler still flagging a tire after a sensor swap, or riding rough since that last trail run? Give 456 AutoFix a call at 616-279-3832 on a weekday from 8am to 5pm, or request a suspension and steering appointment online.

If daytime hours don’t work, the after-hours drop-off lets you leave the Jeep with us on your own schedule. Our shop is at 456 Carrier St NE, Grand Rapids.