456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Tall Enough for 35s? The Best Jack Stands for Lifted Jeep Builds

best jack stands for lifted jeep: peaceful countryside with cornfield and path at sunset under a vivid sky

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

Put a lift kit and 35-inch tires on a Wrangler and the stands that worked on the family sedan suddenly look short. The best jack stands for lifted Jeep work reach well past 20 inches, carry a 6-ton rating and lock with more than one mechanism.

Below: how to measure the height you need, then six tall pairs for a lifted Wrangler or Gladiator. For stands of every size, see our home garage jack stand guide.

Quick answer

Which jack stands suit a lifted Jeep?

Look for a 6-ton pair whose top setting clears your measured axle or frame height by a few inches. The Pro Eagle stands reach 28 inches for big lifts, the Big RED AT46002ABR adds a second lock up to about 23.8 inches, and the TONDA extra tall pair covers milder builds.

Our Quick Picks

Three quick picks for big lifts, 35-inch axle work and milder builds. All six pairs are reviewed below.

Pro Eagle Jack Stands product photo
Tallest reach

Pro Eagle Jack Stands

6 ton pair · 16 to 28 in.

Pin-locked steel stands from an off-road brand, with swappable top posts.

SuitsFrame support on big lifts
View on Amazon →
Big RED AT46002ABR product photo
Double lock

Big RED AT46002ABR

6 ton · 15-3/8 to 23-13/16 in.

Ratchet stands with a second pin lock and a broad black frame.

SuitsAxle work on 35-inch tires
View on Amazon →
TONDA 3 Ton Extra Tall product photo
Mild lifts

TONDA 3 Ton Extra Tall

3 ton pair · 13.39 to 21.06 in.

Lighter tall stands with a low start and a large saddle.

SuitsStock and mildly lifted Jeeps
View on Amazon →

How Tall Is Tall Enough on a Lifted Wrangler or Gladiator?

Measure from the floor to the spot you plan to support, then add the inch or two it takes to get the tire clear of the ground. That total should sit in the middle or upper part of a stand’s range, never past its top notch.

Where you support the Jeep changes the number a lot. Wranglers and Gladiators ride on solid front and rear axles, and the height of an axle tube depends mostly on tire size, because the axle hangs from the wheel centers. Lifting the frame higher with a suspension kit barely moves the axle, but it pushes the frame rails up by the full lift height.

  • Under the axle tubes: the usual spot for tire and brake work. Bigger tires mean a taller tube.
  • Under the frame: lets the suspension droop for shock and control arm work, and is often beyond the reach of car stands on a lifted Jeep.
  • Minimum height: a stand that starts at 17 inches will not fit under a point your jack only raises to 16.

Your jack also has to reach, since many low-profile floor jacks stop short of a lifted frame. Our car jack guide for Jeep owners covers high-reach options.

Ratings, Locks and Bases on Tall Stands

Some makers rate the pair and some rate each stand, so two listings showing “6 ton” may not mean the same thing. Compare the figure with the weight rating on the driver’s door-jamb label, and leave a generous margin for a loaded Gladiator.

Tall stands hold the load further from the floor, so a wide footprint matters, and a ratchet bar backed by a steel pin gives a second lock if the pawl is bumped. When you narrow down the best jack stands for lifted Jeep use, weigh height first, then the locks and base.

Best Jack Stands for Lifted Jeep: Six Tall Pairs Reviewed

Every pair below tops out above 21 inches. Heights and ratings are quoted as each Amazon listing states them.

1. Pro Eagle Jack Stands: 6 Ton Pair with 16 to 28 Inch Height Range

Pro Eagle Jack Stands product photo
Key features
  • 6 ton rating for the pair
  • 16 to 28 in. across 7 settings
  • 18 in. wide base
  • ASME PASE compliant per listing

Pro Eagle is a name many Jeep owners already know from off-road floor jacks, and these heavy-gauge steel stands are built with tall vehicles in mind. The listing rates the pair at 6 tons and states that they are ASME PASE compliant. Height runs from 16 to 28 inches across seven settings, the widest top reach in this group.

Instead of a ratchet bar, the column slides in a low-friction sleeve and is held by a custom locking pin at each setting. That makes adjustment a two-handed job, but the pin gives a clear, positive stop that is easy to check by eye. The 18-inch wide base spreads the load and resists tipping, which matters more as the saddle climbs. Pro Eagle includes two Topography Jack Pads and five interchangeable top posts, so you can match the contact surface to a round axle tube or a flat frame rail.

These suit a Wrangler or Gladiator with a substantial lift, where the frame sits too high for most car stands. With a 16-inch starting height, they will not fit under low points on a stock Jeep, so measure first. They are also large to store, and the blue coating will need touching up after years on a salty garage floor.

View Pro Eagle Jack Stands on Amazon

2. Big RED AT46002ABR: 6 Ton Double Locking Jack Stands, 15-3/8 to 23-13/16 in.

Big RED AT46002ABR product photo
Key features
  • 6 ton (12,000 lb) rating
  • 15-3/8 to 23-13/16 in. range
  • Ratchet bar plus locking pin
  • 10-13/16 x 9-7/16 in. foot base

Big RED is the consumer line from Torin, and the AT46002ABR is its double locking version of a familiar 6-ton ratchet stand. The listing gives a 6-ton (12,000 lb) capacity, sold as a pair, with a height range from 15-3/8 to 23-13/16 inches. That top figure lines up well with axle tube work on a Jeep running 35-inch tires.

Height is set with a single-piece, self-locking forged iron ratchet bar, so you lift the column and it clicks into the next position. A separate pin then passes through the stand as a second lock, which Big RED describes as double-lock protection. The saddle has a large contact area, and the foot base measures 10-13/16 by 9-7/16 inches. The listing includes a limited one-year manufacturer warranty.

This pair is a practical middle choice for owners who switch between axle and frame support on a moderate lift. The ratchet makes height changes quicker than a pin-only stand, and the extra pin adds peace of mind when you are lying beneath a tall vehicle. Owners with very large lifts may still find the frame sits above the top notch, and the black finish shows salt residue quickly, so wipe it down after winter jobs.

View Big RED AT46002ABR on Amazon

picturesque rural road flanked by golden fields under a sunset sky

3. ROADTEK 6 Ton Jack Stands: Double Locking with 15.3 to 24 in. Height

ROADTEK 6 Ton Jack Stands product photo
Key features
  • 6 ton rating per listing
  • 15.3 to 24 in. over 10 levels
  • 11 in. round one-piece steel base
  • Release knob and chained safety pins

The ROADTEK stands take a different approach to the base. Instead of a welded pyramid, each stand sits on an 11-inch diameter round base made from one piece of alloy steel, which the listing says removes the risk of weld cracks. The listed height range is 15.3 to 24 inches across ten levels, and the rating is 6 tons.

Locking works in two stages. A cast iron ratchet bar with a serrated profile holds the height, and a metal pin, kept on a long chain so it does not get lost, goes through as a backup. Release is handled by a self-locking knob rather than a lever, which the maker says helps prevent sudden drops and pinched fingers. The concave saddle cradles the edge of a frame or a round tube, and the rubber-padded handle lets you carry both stands in one hand.

For a Jeep owner, the 24-inch top setting covers axle tubes on most lifted builds and frame rails on milder ones. A round base works best on smooth, flat concrete, so these are less suited to cracked or uneven floors. Check that the 15.3-inch minimum fits under your chosen support point before you buy.

View ROADTEK 6 Ton Jack Stands on Amazon

4. USYATO 6 Ton Jack Stands: 13-Level Double Lock, 17.25 to 23.87 in.

USYATO 6 Ton Jack Stands product photo
Key features
  • 6 ton rating per listing
  • 17.25 to 23.87 in. over 13 levels
  • Cast iron ratchet bar plus metal pin
  • Rubber pads for the saddle

These USYATO stands start higher than anything else in this list. The listing gives a range of 17.25 to 23.87 inches across thirteen levels, so the steps between settings are small, and a 6-ton rating. That combination suits a lifted Jeep where every support point already sits well above a car’s ride height.

The design uses a cast iron ratchet bar with serrated teeth for quick adjustment, plus a removable metal pin as a second lock. The base is a wide pyramid shape in rigid steel with a corrosion-resistant finish, according to the listing. USYATO includes rubber pads that sit on the saddle, which helps protect painted frame rails and powder-coated aftermarket parts from scratches and stops the contact point from sliding on a smooth tube.

Fine height steps help when you want both sides of the axle at exactly the same notch. The trade-off is the tall minimum: at 17.25 inches, these will not fit under a stock Jeep or under a low point on a lifted one, so they work best as a dedicated pair for a built vehicle. Measure the gap between your floor and the support point with the Jeep raised before ordering these.

View USYATO 6 Ton Jack Stands on Amazon

serene winter road lined with evergreen trees under a clear blue sky

5. VEVOR 6t Jack Stands: 13,000 lb Double Locking Pair, 14.2 to 23 in.

VEVOR 6t Jack Stands product photo
Key features
  • 6 t / 13,000 lb rating
  • 14.2 to 23 in. range
  • Ratchet lock plus metal safety pins
  • Pyramid base with triangular foot pads

VEVOR’s 6t stands cover the widest spread of heights in the 6-ton group, from 14.2 to 23 inches according to the listing. The rated capacity is 6 tons, or 13,000 lb, and the listing says the stands conform to CE standards. The lower start makes them easier to share between a lifted Jeep and a stock vehicle in the same garage.

Each stand uses a handle-adjusted locking ratchet bar backed by wear-resistant metal safety pins, giving two separate locks at the chosen height. The base is a wide pyramid in carbon steel with triangular foot pads, which VEVOR says gives a much larger load-bearing area than its earlier design. The ratchet bar is cast iron with a rust-proof coating, and the notched saddle top is shaped to grip the edge of a frame rail.

On a Jeep, the 23-inch top setting suits axle tube support on moderate lifts and frame support on stock or near-stock builds. Big lifts on 37-inch tires may push the frame beyond that reach, so measure before relying on them there. These are a sensible pick when one pair has to handle more than one vehicle, and the coated ratchet bar should cope better with damp winter floors than bare metal.

View VEVOR 6t Jack Stands on Amazon

6. TONDA 3 Ton Extra Tall Jack Stands: 13.39 to 21.06 in. Ratchet Pair

TONDA 3 Ton Extra Tall product photo
Key features
  • 6,000 lb rating per pair
  • 13.39 to 21.06 in. range
  • Self-locking ratchet bar
  • 7.2 x 8.86 in. pyramid base

TONDA labels these as extra tall 3-ton stands, and they fill a gap between ordinary car stands and the heavy 6-ton pairs above. The listing gives a 6,000 lb capacity per pair and a height range of 13.39 to 21.06 inches. That lower start lets them fit under stock Wrangler and Gladiator support points.

Height is set by a sawtooth ratchet bar that engages its lock automatically as you raise the column. The frame is welded carbon steel, the ratchet bar is cast iron with a protective coating, and the pyramid base measures 7.2 by 8.86 inches. A large saddle helps keep good contact with the axle tube or frame rail you are supporting. The set includes two stands.

These make most sense on a stock Jeep or one with a modest lift and tires around 33 inches, where 21 inches of reach is enough for axle work. The lower rating and smaller base mean they are not the right choice for a heavily built Jeep carrying steel armor and a winch, or for frame support on a big lift. Check your door-jamb weight label and compare it with the rating before choosing these over a 6-ton pair.

View TONDA 3 Ton Extra Tall on Amazon

Height and Rating Side by Side

The table puts the six pairs on one page. Match the height column to your tape measure first, then check the rating wording before you settle on the best jack stands for lifted Jeep jobs in your own garage.

PairListed height rangeListed ratingGood match for
Pro Eagle Jack Stands16 to 28 in.6 ton per pairFrame support on big lifts
Big RED AT46002ABR15-3/8 to 23-13/16 in.6 ton (12,000 lb)Axle work on 35s
ROADTEK 6 Ton15.3 to 24 in.6 tonRound base on a smooth slab
USYATO 6 Ton17.25 to 23.87 in.6 tonHigh support points only
VEVOR 6t14.2 to 23 in.6 t (13,000 lb)Mixed stock and lifted use
TONDA 3 Ton Extra Tall13.39 to 21.06 in.6,000 lb per pairMild lifts and lighter jobs
Tall jack stands for lifted Jeeps compared by listed height and rating

If your measured height lands within an inch of a pair’s top setting, move up to a taller one. Owners who also work on full-size pickups can compare heavier options in our roundup of jack stands for trucks.

curving mountain road

Setting a Lifted Jeep on Stands in a Michigan Garage

A tall Jeep on tall stands carries its weight high, so follow the same routine every time. Australia’s product safety regulator puts it plainly: never get under a vehicle held up only by a jack, and make sure it is secure on the stands first.

  1. Flat concrete only: gravel or a sloped driveway can let a base shift or sink.
  2. Chock and park: set the parking brake and chock the tires that stay down.
  3. Lift at a solid point: use the points in your owner’s manual and keep the jack centered on a round axle tube.
  4. Match the notches: set both stands at the same height, then lower the Jeep onto the saddles.
  5. Test first: push on the bumper, watch the stands and leave the jack lightly in place as a backup.
serene forest road bathed in autumn light

Years of road salt can scale a Jeep’s frame and axle tubes, so check each support spot for flaking metal first. A stand pair is only one part of a home setup, and our list of car maintenance tools for beginners covers chocks, a torque wrench and the rest.

Jobs That Belong on a Shop Lift

Stands suit wheel swaps, brake checks and fluid changes. Heavy suspension work or hours under the Jeep is safer on a two-post lift.

picturesque winter scene with a winding road through snow-covered trees and hills

Our factory scheduled maintenance in Grand Rapids covers the items in your Jeep’s maintenance schedule with it raised on a lift. If a lifted front end has started to wander or clunk, our suspension repair service can inspect the steering and suspension parts, and our guide to shocks for Jeep models explains what changes with a lift.

Frequently Asked Questions

How tall should jack stands be for a Jeep on 35-inch tires?

Measure your own Jeep, since lifts vary. For axle tubes on 35s, stands topping out around 23 to 24 inches usually leave room, while frame support on a big lift can need the 28-inch Pro Eagle.

Where do jack stands go on a Wrangler or Gladiator?

Under the solid axle tubes near the wheels for tire and brake work, or under the frame rails when the suspension needs to hang. Your owner’s manual shows the factory lifting points.

Are 3-ton jack stands enough for a lifted Jeep?

Often, but check the door-jamb weight label and whether the rating covers the pair or each stand. Builds with steel bumpers, a winch or a loaded Gladiator bed suit a 6-ton pair.

What are the best jack stands for Jeep Wrangler owners who have not lifted yet?

A pair with a lower starting height, such as the TONDA extra tall or VEVOR 6t, fits under stock support points and still leaves room for a future lift.

Rather have a lifted Jeep looked over on a proper lift? Phone 456 AutoFix at 616-279-3832 between 8am and 5pm, Monday to Friday, or request a time on our contact page.

Working during shop hours? Our after-hours drop-off lets you leave the Jeep at 456 Carrier St NE in Creston and we’ll take it from there.