As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
Once you decide that Bilstein is the brand for your European car, the next choice happens inside the catalog. The bilstein b4 vs b6 question comes up because both lines are listed for the same cars, often side by side, and the part numbers look almost alike. One is meant to put the car back the way the factory built it, and the other is meant to tighten things up a little.
To keep this fair, we compare the two lines in general, then hold one front strut from each against the other for a single car: the 2017-2019 Volkswagen Golf Alltrack, the raised wagon version of the Mk7 Golf. If you want more brands and styles in the mix, our roundup of shocks and struts for daily drivers covers a wider field. We also add one non-Bilstein pair for the same corner as a reference point.
Quick answer
Should you choose the Bilstein B4 or the B6?
Pick the B4 if you want the ride and handling your car had when new, since Bilstein builds it as an original equipment replacement. Pick the B6 if you want firmer, more controlled damping on stock springs, from a monotube design. Both carry Bilstein’s Limited Lifetime Warranty in North America.
Our Quick Picks
One front strut from each Bilstein line for the same 2017-2019 Golf Alltrack corner, plus an A-Premium pair listed for that position. All three are reviewed in full below.

Bilstein B4 22-274182
Factory-matched strut meant to bring back the Alltrack's original ride.

Bilstein B6 35-273806
Firmer monotube upgrade that keeps the stock springs and ride height.

A-Premium Front Bare Strut Pair
Non-Bilstein left and right pair listed for the same Alltrack front position.
What the B Numbers Mean at Bilstein
Bilstein sorts its range with a simple letter and number code, and the higher the number, the further a part moves from stock. Its help center page on B4, B6 and B8 products sets out the split in a few lines. B4 parts are original equipment replacements, with the same valving profile, ride height and fitment as the dampers the carmaker installed.
B6 for passenger cars, which Bilstein also calls B6 Performance, is a step up from factory dampers. Bilstein says it is designed to work with the stock height factory spring and uses application specific valving in a monotube body. The next tier, B8 Performance Plus, is for cars running aftermarket lowering springs, so it sits outside this comparison.
That split matters more than any spec sheet. If your car still sits on its original springs and you have no plans to lower it, both B4 and B6 are in play. If you have already fitted lowering springs, neither of these is the part Bilstein points you to.
Twin-tube and monotube in plain terms
A twin-tube damper has an inner working cylinder inside an outer reserve tube, and oil moves between the two as the piston travels. A monotube damper uses one larger cylinder, with the oil and a high pressure gas charge kept apart by a floating piston. The single tube gives room for a bigger piston and lets heat leave the body more directly.
Bilstein states that the B6 Performance is a monotube design. For the B4, Bilstein’s own Amazon titles for other Golf front struts, such as 22-230522, call them twin-tube units, while the Alltrack listing we cover does not name the construction. Treat the B4 here as a factory-style damper and the B6 as the monotube upgrade, which is how Bilstein positions them.
How to Choose Between the Two Lines
Start with how the car feels today and how you want it to feel after the job. Most owners shopping for new struts have a car that floats over dips, wallows in turns or thumps over broken pavement. Fresh dampers from either line will fix the worn feel, so the real decision is whether you want factory comfort back or a tauter ride than the car had new.
A few questions narrow it down quickly:
- Do you mostly commute, or do you enjoy back roads and long highway curves?
- Does the car often carry a full load, a roof box or a bike rack?
- Has anyone in the household complained about a firm ride in the past?
- Are your springs original, healthy and at stock height?
- Does the car have electronically adjustable dampers, which need a different part?
The last point is easy to miss on a Volkswagen or BMW. Cars with adaptive or electronic damping, such as VW’s DCC option on some Golf models, use struts with wiring that a plain B4 or B6 does not have. Check your build sheet or the Amazon fit notes before you order.
Bilstein B4 vs B6 on One Golf Alltrack Front Corner
The first two struts below are Bilstein listings for the front of the 2017-2019 Volkswagen Golf Alltrack, and the third is an A-Premium pair listed for the same spot, so all three replace the same factory part. Neither Bilstein listing names a side, so check the fitment notes and plan on buying a matching pair for the front axle.
Bilstein B4 22-274182: OE Replacement Front Strut for 2017-2019 VW Golf Alltrack

- OE replacement strut for 2017-2019 Golf Alltrack
- Valving and ride height to factory spec
- Bilstein gas-pressure technology
- Constant damping under any load
The 22-274182 is Bilstein’s B4 OE Replacement front strut listed for the 2017-2019 Volkswagen Golf Alltrack, the lifted, all-wheel-drive wagon built on the Mk7 Golf. Bilstein’s B4 line is meant to match the factory part, with the same valving profile, ride height and fitment as the damper Volkswagen installed. The listing does not name a side, so confirm the position in the fitment notes and order two.
The listing promises an optimum driving experience as on day one, along with high power reserves and constant damping power under any load. Bilstein credits its gas-pressure technology for traction and precise handling. The listing does not state the internal construction, although Bilstein titles several other B4 Golf front struts as twin-tube units.
This is the strut on its own, with no spring or top mount mentioned, so your existing parts move across and a spring compressor is needed for the swap. It suits an Alltrack owner on healthy factory springs who wants the car to ride and steer the way it did when new, without a firmer feel. It is not meant for lowered cars or for cars with electronically adjustable dampers, so check the build before buying. Bilstein’s North American warranty page lists the B4 OE Replacement line under its Limited Lifetime Warranty.
View Bilstein B4 22-274182 on Amazon

Bilstein B6 35-273806: Monotube Front Strut for 2017-2019 VW Golf Alltrack

- Monotube front strut for 2017-2019 Golf Alltrack
- Works with the factory series spring
- Tuned by Bilstein in road testing
- Extra reserves for loads and trailers
The 35-273806 is the B6 monotube front strut that Bilstein lists for the same 2017-2019 Volkswagen Golf Alltrack, so it fills the exact spot the B4 above does. Bilstein positions the B6 Performance line as an upgrade over factory dampers that is designed to work with the stock height spring. Buy a matching pair for the front axle.
The listing points to higher power reserves and a longer service life when the car pulls a trailer or carries loads often. It also claims better grip and lane stability in everyday driving and extreme situations, and says each application is fine-tuned in Bilstein road testing. The monotube body uses Bilstein gas-pressure technology, and the listing notes that the factory series spring can stay on the car, so no spring change is required.
Your spring and top mount still transfer from the old strut, so the job calls for a spring compressor. The B6 suits an owner who wants a more planted, controlled feel, especially with a full load, and who does not mind a firmer ride. It is not the right choice for a car on lowering springs, where Bilstein points to the B8 line instead. Bilstein’s North American warranty page lists B6 Performance under its Limited Lifetime Warranty.
View Bilstein B6 35-273806 on Amazon

A-Premium Front Bare Strut Pair: Single-Pipe Gas Struts for 2017-2019 Golf Alltrack

- Front left and right struts, sold as a set of two
- Fitment lists the 2017-2019 Golf Alltrack
- Gas-charged, single-pipe construction
- One-year unlimited-mileage guarantee
For a point of reference outside Bilstein, this A-Premium listing covers the same front position on the 2017-2019 Golf Alltrack and ships as a set of two, one strut for each side. It is a bare unit with no coil spring, so it does the same job as the B4 and B6 above. The fitment list also names the Golf R, GTI, Arteon and several Audi A3, S3 and TT Quattro models, so it is a shared platform part rather than one listed for the Alltrack alone.
A-Premium describes it as a gas, single-pipe design, which is another way of saying monotube. The listing gives an extended length of 19.65 inches, a compressed length of 16.97 inches and a stroke of 2.68 inches. It also prints OE reference numbers such as 8S0413031A, which you can match against the part coming off the car.
Unlike Bilstein, A-Premium makes no claim about ride feel or handling, so treat it as a plain replacement rather than a tuned upgrade. Your springs and top mounts carry over, just as they do with the Bilstein struts. Coverage is a one-year unlimited-mileage guarantee, much shorter than Bilstein’s lifetime terms.
View A-Premium Front Bare Strut Pair on Amazon
Bilstein B4 vs B6 Specs Side by Side
The table uses only what the Amazon US listings and Bilstein’s own pages say. Any spec Bilstein or the listing leaves out is marked “not stated” below.
| Point | B4 22-274182 | B6 35-273806 | A-Premium pair |
|---|---|---|---|
| Line | B4 OE Replacement | B6 Performance upgrade | Aftermarket replacement |
| Vehicle in listing | 2017-2019 VW Golf Alltrack, front | 2017-2019 VW Golf Alltrack, front | 2017-2019 VW Golf Alltrack, front |
| Construction | Not stated on this listing | Monotube | Gas, single pipe |
| Maker’s goal | Driving feel as on day one | More grip and lane stability | Not stated |
| Springs | Factory stock height | Factory spring can be reused | Bare strut, reuse your spring |
| Loads and towing | Constant damping under any load | Higher reserves when towing or loaded | Not stated |
| Warranty (maker terms) | Limited Lifetime | Limited Lifetime | One year, unlimited mileage |
Bilstein’s North American warranty page lists both B4 OE Replacement and B6 Performance under its Limited Lifetime Warranty for products bought through a Bilstein distributor in North America, with exclusions. Keep your receipt, because the page says claims start with the original place of purchase.

Which Driver Each Strut Suits
In the Bilstein B4 vs B6 decision, neither line is better for everyone. Match the part to the way the car is driven, and remember that both corners of an axle should get the same line.
| Your situation | Better fit | Why |
|---|---|---|
| Daily commute, comfort first | B4 | Matches factory valving and ride height |
| You liked how the car drove new | B4 | Built to restore original feel |
| Back roads and quicker turn-in | B6 | Monotube, tuned for handling |
| Roof box, full cabin or trailer | B6 | Listing cites reserves under load |
| Lowering springs already fitted | Neither | Bilstein points to B8 for lowered cars |
Owner forums for BMW and VW models often describe the B6 as noticeably firmer than stock, and a few owners say they went back to B4 because the ride felt busy on rough pavement. That is opinion rather than a maker claim, but it is a fair warning if someone in your family already finds the car stiff. If you enjoy a planted feel and the car spends time on twisty roads, the B6 is the more natural fit.
Still weighing the bilstein b4 vs b6 choice for a different VW, such as a Jetta, GTI or Tiguan? Our Volkswagen shocks and struts guide goes model by model.
Michigan Roads and the Install Itself
West Michigan winters are rough on front struts. Freeze-thaw cycles open potholes across Grand Rapids every spring, and road salt creeps into the strut body, spring seat and pinch bolt threads. In a Bilstein B4 vs B6 choice for local roads, the firmer B6 transmits a little more of a sharp pothole edge into the cabin, while a B4 soaks up more of it, which is worth weighing if your commute crosses broken streets.
All three listings are for the strut on its own, with no spring or top mount in the box, so plan on moving yours over. That means compressing the coil spring, which stores enough energy to cause serious injury if a tool slips. Read our guide to coil spring compressors first, and do not use a bent or worn set.

Replace front struts as a pair, and use the same line on both sides. A B4 on one corner and a B6 on the other gives two different damping rates across the axle, which can make the car pull under braking and lean unevenly in turns. Mixing lines front to rear is a separate choice, and most owners keep the whole car on one line so the balance stays predictable.
On a strut front end like the Golf’s, the strut helps hold camber, so book a four-wheel alignment after the job. Rusted fasteners are common on cars that have seen a few Michigan winters, so soak the bolts with penetrant the night before.
When to Let a Shop Take It
Not sure the struts are the cause? Bouncing after dips, nose dive when you brake, oil streaks on the strut body and cupped tires are the usual signs, and our article on how to tell if struts are bad walks through each one. A clunk over bumps can also come from sway bar links or worn bushings, so rule those out before you spend money.

If you lack a safe lift, a good spring compressor or the patience for seized bolts, a shop is the safer route. Our team handles suspension repair in Grand Rapids and works on European models through our foreign car repair service. Steering and suspension is one of the areas where Hendrick Hoffman holds both ASE and State of Michigan certification, and we inspect the mounts, links and ball joints while the corner is apart.
Comparing Bilstein with other brands rather than with itself? Our KYB vs Monroe struts comparison uses the same one-car method.
More Buying Guides
Frequently Asked Questions
Is the Bilstein B6 too stiff for daily driving?
For most drivers, no. Bilstein designs the B6 Performance to run on stock height factory springs, so the car keeps its normal ride height. It does feel firmer than stock, and owners who want the softest ride on broken pavement often stay with the B4.
Can I put B6 struts on with my original springs?
Yes, that is what the B6 is for. The Golf Alltrack listing says the factory spring can be reused. If your car is on lowering springs, Bilstein points you to the B8 line instead.
Can I mix a B4 and a B6 on the same axle?
We advise against it. The two lines damp at different rates, so one of each across an axle can make the car pull or lean unevenly. Fit the same line on both sides.
Do B4 and B6 struts come with a warranty?
Bilstein’s North American warranty page lists both B4 OE Replacement and B6 Performance under its Limited Lifetime Warranty, with exclusions. Buy from an authorized seller and keep your proof of purchase.
Golf still floating over dips, or not sure which Bilstein line suits the way you drive? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or ask for a suspension inspection through our contact page.
Tied up at work until after we close? Our after-hours drop-off at 456 Carrier St NE means you can leave the Golf with us whenever your day ends.
