456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Low Noses and Jack Pads: The Best Floor Jack for Porsche

best floor jack for porsche: sports car raised on a lift in a garage

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A 911 or a Cayman sits close to the ground, and the front spoiler is usually the first thing a garage jack hits. The best floor jack for Porsche owners slides under that nose, reaches back to the factory lift point and still raises the car high enough for a pair of stands.

This guide covers what to measure, how to protect the jack points and six floor jacks that suit these cars. For a wider look at low jacks on any make, see our roundup of low profile floor jacks for cars.

Quick answer

What kind of floor jack does a Porsche need?

Look for a minimum saddle height under about 3.5 inches, a long reach and a rubber saddle or puck that protects the jack pad. The ARCAN A20016 starts at 2.75 inches with extra reach, the Powerbuilt 620479E also starts at 2-3/4 inches, and the ARCAN A20004 suits a Macan or Cayenne.

Our Quick Picks

Three jacks that cover the main Porsche situations: a low nose, a very low or lowered car, and a taller SUV.

ARCAN A20016 product photo
Low nose, long reach

ARCAN A20016

2 ton steel | 2.75 to 24 in.

Starts very low and reaches deep under the sills.

Suits911, Cayman and Boxster owners
View on Amazon →
Powerbuilt 620479E product photo
Very low cars

Powerbuilt 620479E

2 ton steel | 2-3/4 to 15-1/4 in.

Slides under lowered cars and adds a locking bar.

SuitsLowered or track-prepped cars
View on Amazon →
ARCAN A20004 product photo
Porsche SUVs

ARCAN A20004

3 ton hybrid | 4 to 18.5 in.

Higher lift and extra capacity in a lighter frame.

SuitsMacan, Cayenne and Panamera
View on Amazon →

What a Porsche Asks of a Floor Jack

Start with a tape measure, not a catalog. Slide it under the car in a straight line toward the lift point you plan to use, and note the lowest thing along that path: the front lip, a side skirt or an underbody tray. The jack’s listed minimum height has to clear that figure with a little room to spare.

Reach is the second number. Porsche lift points sit under the sills, well inside the bodywork on a 911 or Panamera, so a short jack can run out of frame before the saddle arrives. A long chassis lets you keep the handle and the jack body out from under the bumper while the saddle does the work.

Lift range matters most on the SUVs. A Cayenne or Macan clears a regular jack easily but needs more height before a stand fits.

Car makers design and mark their lift points for exactly this job, and SAE International publishes a standard on how those points should be laid out and labeled, SAE J2184 for vehicle lift points in service garages. Your owner’s manual shows where they are on your model, and that diagram is the one to follow.

Saddles, Pucks and Jack Pad Adapters

Many Porsches have small pads or receptacles at the factory lift points instead of a bare pinch weld. A metal saddle pressed straight onto one can crack the pad or slip off it. Owners usually set a rubber puck or a shaped adapter between the saddle and the pad to spread the load and keep the jack centered.

Adapter shapes vary by model and year, and some newer cars use square receptacles that a round hockey puck doesn’t fit well. Check that whatever goes on the saddle seats firmly in both the jack cup and the car’s pad before you pump.

Best Floor Jack for Porsche: Six Jacks in Detail

The heights and capacities below are as each Amazon listing states them. Hold every minimum height up against the measurement you took under your own car.

1. ARCAN A20016: 2 Ton Steel Floor Jack with Extra Long Reach

ARCAN A20016 product photo
Key features
  • 2 ton (4,000 lb.) capacity
  • 2.75 to 24 in. listed lift range
  • Dual pump pistons for quick rise
  • Listed as ASME PASE-2019 compliant

The ARCAN A20016 is a steel service jack built around two numbers that matter on a low car: a 2.75 inch minimum height and a 24 inch maximum, as the listing states. That spread lets the saddle slip under a tight front lip and still climb high enough to set a jack stand under a sill at a comfortable working height. The long chassis is the other reason it suits a Porsche.

Because the frame is extra long, the saddle can reach a lift point that sits well inboard while the jack body and handle stay clear of the bumper cover. Dual pump pistons raise the saddle to the contact point in fewer strokes, and the rubber saddle and foam-covered handle help protect paint and pads. ARCAN lists the jack as meeting ASME PASE-2019 and backs it with a one year warranty.

The trade-off is size and weight. A long steel jack is happiest rolling around one garage floor and is awkward to lift into a trunk or carry to a track day. Its 2 ton rating is plenty for lifting one corner or one side of a sports car, but it is not meant for heavier trucks. For a 911 or Cayman kept at home, it covers both clearance and height.

View ARCAN A20016 on Amazon

2. Powerbuilt 620479E: 2 Ton Xtra Low Profile Floor Jack with Safety Bar

Powerbuilt 620479E product photo
Key features
  • 2 ton load capacity
  • 2-3/4 to 15-1/4 in. listed lift range
  • Locking safety bar at maximum height
  • Ball bearing swivel casters

Powerbuilt’s 620479E is aimed at cars with almost no gap under the nose. The listing gives a starting height of 2-3/4 inches and a top height of 15-1/4 inches, with a 2 ton capacity. That low entry point makes it a fit for a lowered 911, a Cayman on track suspension or any car where most jacks touch the front spoiler first.

The feature that sets it apart is a locking safety bar that supports the lifted load at maximum height. Ball bearing swivel casters let you steer it into position under a long nose, and Powerbuilt says the jack meets or exceeds ASME standards. It is a sensible setup for tire swaps, quick brake checks and getting a car high enough to slide a taller jack underneath.

The listing says the safety bar removes the need for extra jack stands, but we still treat it as a backup only and put rated stands under the car before anyone reaches underneath. The 15-1/4 inch ceiling is also modest, so on many cars it will not lift high enough for stands at a roomy working height. For very low cars, it is a strong first jack to reach for.

View Powerbuilt 620479E on Amazon

Four wrenches on a wooden table

3. Pro-Lift F-767: 2 Ton Steel Low Profile Floor Jack with Bypass Device

Pro-Lift F-767 product photo
Key features
  • 2 ton capacity, steel build
  • 3-3/8 to 15 in. listed lift range
  • Patented bypass against over pumping
  • Built-in overload safety valve

The Pro-Lift F-767 is a straightforward steel floor jack with a 2 ton rating and a lift range of 3-3/8 to 15 inches, according to its listing. That starting height clears the front of many stock-height Porsche coupes and roadsters, though a lowered car or one with an aftermarket splitter may need something lower. Measure the gap first and compare it with that figure.

Pro-Lift fits a patented bypass device that protects the jack against over pumping once it reaches full height, plus a built-in safety valve for overload protection. The steel construction gives it weight and stability on a concrete floor, and the casters let you position it under the car without much effort. It is the kind of jack that does seasonal wheel changes year after year with little fuss.

Its limits are reach and height. The top figure of 15 inches suits wheel work, but you may want more lift when setting stands for a longer job under the car. There is no aluminum option here, so it is not the lightest jack to carry. If you only swap wheels twice a year on a Boxster or 911, it covers that job well.

View Pro-Lift F-767 on Amazon

4. ARCAN A20004: 3 Ton Hybrid Aluminum and Steel Low Profile Floor Jack

ARCAN A20004 product photo
Key features
  • 3 ton (6,000 lb.) capacity
  • 4 to 18.5 in. listed lift range
  • Hybrid aluminum and steel frame
  • Side carry handle for positioning

ARCAN’s A20004 combines an aluminum and steel frame with a 3 ton capacity and a listed lift range of 4 to 18.5 inches. A 4 inch starting height is higher than the other jacks here, which makes it a better match for a Macan, Cayenne or Panamera than for a low 911. Those cars need lift height and capacity more than a very low entry point.

Dual pump pistons bring the saddle up to the load quickly, and the reinforced lift arm helps keep the chassis steady as it rises. The rubber saddle and foam handle bumper protect the lift points and paint, and a side carry handle makes it easier to move around the garage. ARCAN covers it with a one year warranty, as the listing states.

Because the frame is part aluminum, it is lighter than an all-steel jack of similar capacity, so moving it between two cars in a shared garage is easier. The catch is clearance. On a sports car with a low front lip, measure carefully, since 4 inches may not clear without driving onto low ramps first. For a household with a Porsche SUV, it is a balanced choice.

View ARCAN A20004 on Amazon

Man opening a tool case on the ground

5. Torin Craftsman 2.5 Ton: Aluminum and Steel Racing Floor Jack with Dual Piston Pump

Torin Craftsman 2.5 Ton product photo
Key features
  • 2.5 ton (5,000 lb) capacity
  • 3-15/16 to 18-5/16 in. listed lift range
  • Aluminum and steel hybrid build
  • Dual side handles for carrying

This Torin jack, sold under the Craftsman name, is a racing-style floor jack with a 2.5 ton capacity and a listed lift range of 3-15/16 to 18-5/16 inches. The hybrid aluminum and steel construction keeps weight down, and dual side handles make it easy to pick up and move. That combination suits owners who work in a driveway or take the car to track days.

A dual piston quick lift pump raises the saddle to the lift point in fewer strokes, which helps when you are working around four corners in a session. The built-in foam bumper on the handle protects the car if the handle swings toward the bodywork. Torin backs the jack with a one year limited warranty, according to the listing.

With a starting height just under 4 inches, it will clear many stock Porsches but not every low front lip, so measure your car before you buy. The top figure of just over 18 inches gives enough room to set stands at a useful height on most cars. If portability matters more than the very lowest entry point, it is a practical middle ground.

View Torin Craftsman 2.5 Ton on Amazon

6. Liftmaster 2.5 Ton Low Profile Jack Ver. 2: 3.15 in. Extra Low Steel Floor Jack

Liftmaster 2.5 Ton Ver. 2 product photo
Key features
  • 2.5 ton capacity
  • 3.15 in. extra low profile
  • 3.15 to 14.5 in. listed lift range
  • Heavy duty steel construction

The Liftmaster 2.5 Ton Low Profile Jack Ver. 2 keeps things simple. Its listing gives a 3.15 inch extra low starting height, a lift range up to 14.5 inches and heavy duty steel construction. That low entry clears the nose of many Porsche coupes and roadsters, and the 2.5 ton rating is well above what one corner of a sports car puts on the saddle.

Its strength is the low entry point in a plain steel package. It is suited to the jobs most owners do at home: swapping between summer and winter wheels, checking brake pads, looking at a tire or a wheel bearing, and lifting a corner so a stand can go underneath. The steel build adds weight that keeps it planted on a garage slab while you pump.

The listing is short, so check details such as saddle size and handle length on Amazon before you order. The 14.5 inch maximum is the lowest top height in this guide, so it is better for wheel work than for jobs that need the car up high on stands. If you need a low jack for routine tasks, it fits that role.

View Liftmaster 2.5 Ton Ver. 2 on Amazon

Matching a Jack to Your Porsche

Here is the shortlist in one view, grouped by the kind of car each jack suits.

JackCapacity and frameListed lift rangeSuits
ARCAN A200162 ton, steel2.75 to 24 in.Low 911 and Cayman noses, long reach
Powerbuilt 620479E2 ton, steel2-3/4 to 15-1/4 in.Very low or lowered cars
Pro-Lift F-7672 ton, steel3-3/8 to 15 in.Tire swaps on coupes and roadsters
ARCAN A200043 ton, aluminum and steel4 to 18.5 in.Macan, Cayenne and Panamera
Torin Craftsman 2.5 ton2.5 ton, aluminum and steel3-15/16 to 18-5/16 in.Carrying to a driveway or event
Liftmaster 2.5 ton Ver. 22.5 ton, steel3.15 to 14.5 in.Simple wheel and brake jobs
Best floor jack for Porsche models compared by capacity, frame and the lift range each listing gives.

If you own a 911 and a Cayenne, one long-reach jack with a high top end can cover both. If you only own the sports car, a lower entry height matters more than the last few inches of lift.

Hands using a wrench on a machine

Lifting Safely Through a Michigan Winter

Treat the floor jack as the tool that raises the car and nothing more. Lift only at the factory points, set rated jack stands on solid, level concrete, then lower the car onto the stands before any part of you goes underneath. Never work under a Porsche held up by the jack alone.

  • Chock the wheels that stay down and set the parking brake, or leave a manual car in gear.
  • Roll the jack in slowly and watch the front lip and side skirts as the saddle rises.
  • Open the release valve gently when lowering and keep feet clear of the handle.
  • Refit each wheel and torque the lug nuts or wheel bolts to the owner’s manual spec in a star pattern.
Wrenches hanging in a row

Seasonal wheel swaps in Grand Rapids often happen in a cold garage, where slabs can be damp or icy, so wipe the floor dry where the jack and stands sit. Road salt also works on underbody metal and pads, so look closely at each lift point before you put weight on it, and use a calibrated wrench for the wheel bolts; our guide to torque wrenches for Porsche covers that step.

When the Job Belongs on a Lift

A good floor jack handles tire changes, brake checks and a look underneath. Jobs that need the whole car level and high, or a lift point that looks damaged or corroded, are better done on a two-post lift. A jack is one piece of a home kit, and our starter list of car maintenance tools for beginners shows the rest.

Workbench with tools against a wall

When your Porsche reaches its next interval, our factory scheduled maintenance service in Grand Rapids works through the owner’s manual checklist with the car up on a lift. For anything else you spotted underneath, our foreign car repair team can take a closer look.

Frequently Asked Questions

What is the best floor jack for Porsche 911 owners?

One with a minimum height below the clearance under your car’s nose and enough reach to get to the sill lift points. In this guide, the ARCAN A20016 and the Powerbuilt 620479E both list a 2.75 inch starting height.

Where do I put the jack on a Porsche?

Only at the lift points your owner’s manual shows. On many models these are pads under the sills, and a puck or adapter between saddle and pad keeps the jack centered and the pad intact.

Do I need a hockey puck for jacking a Porsche?

Many owners use one, or a model-specific adapter, so bare metal never meets the pad. Make sure it seats firmly, since some newer cars use square receptacles that a round puck doesn’t fill.

Is aluminum or steel better for a Porsche floor jack?

Aluminum or hybrid jacks are lighter to carry to a driveway or a track day. Steel jacks are heavier but sit firmly on one garage floor, so pick by where the jack will live.

Prefer to skip the jacking and the cold floor? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or request a time through our contact page.

If your workday runs into our hours, drop the keys off after closing using our after-hours service at 456 Carrier St NE, on the Creston side of Grand Rapids.