As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A Chrysler 300 that floats over highway seams, or a minivan that wallows into every driveway apron, is telling you its dampers have worn out. Finding the best shocks and struts for Chrysler models starts with the car itself, because a 300 sedan, a Town & Country and a Pacifica share almost no suspension parts.
This guide sorts six listings by model, generation and corner. If you are shopping for a different make, our overview of shocks and struts for daily drivers covers the wider field.
Quick answer
Which shocks and struts should a Chrysler owner buy?
Match the part to your model first. For a 2011 to 2020 Chrysler 300, a loaded Monroe Quick-Strut restores the factory ride, while Bilstein B6 dampers firm it up. Town & Country owners can bolt in a Monroe Quick-Strut, and the Pacifica takes Monroe OESpectrum struts.
Our Quick Picks
Three quick picks: a loaded Monroe for the 2011 to 2020 Chrysler 300, a Bilstein B6 front damper for a firmer 300 and a loaded Monroe for the 2011 to 2016 Town & Country. All six listings are reviewed below.

Monroe Quick-Strut 672665
A complete bolt-in front corner that renews the spring and mount too.

Bilstein B6 24-326421
A performance replacement that keeps the stock spring and height.

Monroe Quick-Strut 471128L
A complete corner that restores ride height on a worn van.
Three Chryslers, Three Different Suspensions
Most Chrysler owners on the road today drive one of three vehicles, and each uses its own hardware:
- Chrysler 300 (2011 and later): a rear-drive sedan, with AWD on some trims. It carries a coil-over strut at each front wheel and a separate shock and coil spring at each rear wheel.
- Town & Country (2008 to 2016): a front-drive minivan with MacPherson struts up front and plain shocks at the rear.
- Pacifica (2017 and later): the current minivan, with different struts again. Hybrid and AWD versions often need their own listings.
On every one of these, the rear dampers are shocks rather than struts, so a full refresh is usually two front struts and two rear shocks. Check each title for years, drive type and side, then confirm in Amazon’s fit checker.
Loaded Assembly or Bare Damper?
A loaded strut, sometimes called a quick strut or complete strut, arrives with the damper, coil spring and top mount already put together. You unbolt the old corner and bolt the new one in. It also replaces a sagging spring and a cracked mount at the same time, which is useful on a car past 100,000 miles.
A bare strut is the damper alone. The factory spring has to be compressed, pulled off the old unit and fitted to the new one, and a compressed spring holds a lot of stored energy. Before trying that at home, read our guide to coil spring compressors for strut work.
Best Shocks and Struts for Chrysler: Six Listings by Model
Each listing below names the Chrysler model and years it covers, and most are sold one corner at a time. Replace dampers in axle pairs and confirm the year, model, engine and drive type on Amazon before buying.
1. Monroe Quick-Strut 672665: Loaded Front Strut and Coil Spring Assembly for 2011-2020 Chrysler 300

- Listed for 2011-2020 Chrysler 300
- Strut, coil spring and upper mount preassembled
- No spring compressor needed
- Salt spray tested protective coating
The Monroe Quick-Strut 672665 is a complete front corner for the second-generation Chrysler 300, and the listing gives its fit as the 2011 to 2020 model years. The title does not say which side it is for or whether it suits rear-drive or AWD cars, so run your year, engine and drive type through Amazon’s fit checker and read the qualifier notes before ordering. Plan on buying the matching part for the other side as well.
Each unit comes with the damper, an application-specific coil spring and the upper mount already assembled. Monroe says the spring is calibrated to the original design to bring back factory ride height, and that the upper mount helps cut noise, vibration and memory steer, the slow return to center that a worn mount can cause. The steel carries a protective coating that Monroe checks with salt spray testing.
The main benefit is a simpler job. With the spring held captive inside the assembly, you remove the old corner and bolt this one in without touching a spring compressor. It suits a 300 that has started to sag, float or clunk with age and an owner who wants the original feel back. It is not aimed at drivers looking for a lowered stance or a sportier, tighter ride.
View Monroe Quick-Strut 672665 on Amazon
2. Gabriel G51721 Ultra: Twin-Tube Rear Shock Absorber for 2005-2022 Chrysler 300 RWD

- Listed for 2005-2022 Chrysler 300 RWD
- Twin-tube design, sold as one shock
- Bolt-on installation
- 6.94 in stroke, 24.88 in extended length
The Gabriel G51721 Ultra is a rear shock absorber that the listing fits to the 2005 to 2022 Chrysler 300 with rear-wheel drive. The same part is also listed for rear-drive Dodge Charger, Challenger and Magnum models, which share the platform. It is sold as a single shock, so order two to do both rear corners together, and leave AWD cars to a listing that names them.
Gabriel describes it as a premium OE replacement with a precision twin-tube design. The listing gives the key dimensions: a 6.94 inch stroke, a 24.88 inch extended length and a 17.95 inch collapsed length, with S55 upper and ES87 lower mount codes. Those numbers are handy if you want to compare it against the part you are taking off. The interchange list also cross-references several other brands’ numbers for the same position.
On the 300 the rear coil spring sits separately from the shock, so this is a simple bolt-on swap with no spring work involved. It suits a rear end that bounces after dips, squats under load or feels loose over rough pavement, and it pairs well with fresh front struts. Owners after a noticeably firmer or sportier rear should look at a monotube damper instead.
View Gabriel G51721 Ultra on Amazon

3. Bilstein B6 24-326421: Front Left Monotube Damper for 2011 and Later Chrysler L-Series

- Listed for 2011 and later Chrysler L-series
- Front left position
- Reuses the factory coil spring
- Uses OEM mounting locations
The Bilstein 24-326421 is a B6 series front damper for 2011 and later Chrysler L-series cars, the rear-drive platform the 300 is built on. It covers the front left corner only, so you need the matching right-hand part for a proper pair. Because the title does not name a drive type or trim, confirm your exact 300 in Amazon’s fit checker before you buy.
Bilstein’s B6 line is its performance replacement range. The listing says the damper uses the car’s factory coil springs and original mounting points for a direct fit, so ride height stays where the factory set it and the car can be aligned to stock specifications. The focus is on more precise handling and steadier body control than a basic OE-style part provides.
This is a bare damper, which means the old spring and top mount have to come off the worn unit and go onto this one. That calls for a spring compressor rated for the job, or a shop that has one. It suits 300 owners who want the car to feel flatter and more settled through corners and on the highway, and it is less suited to anyone after the softest possible ride. Bilstein lists the B6 range under its North American limited lifetime warranty.
View Bilstein B6 24-326421 on Amazon
4. Bilstein B6 Performance 24-216951: Rear Shock Pair for 2011-2014 Chrysler 300 RWD and AWD

- Listed for 2011-2014 Chrysler 300
- Rear pair of two shocks
- Fits AWD and RWD cars
- Washers, bushings and nuts included
This listing packs two Bilstein B6 Performance rear shocks, part number 24-216951, for the 2011 to 2014 Chrysler 300. The title and feature list say it fits both all-wheel-drive and rear-drive cars, which makes it one of the few rear options here that covers an AWD 300. Later model years may use a different part, so check your year in the fit checker first.
The kit includes the washers, bushings, reservoir clamps and nuts needed for the swap, and the factory shock mounting bolts are reused. One detail to note before you start is that mounting plates are sold separately, so look at how your old shocks are held in place and order anything extra ahead of time. Bilstein lists B6 Performance parts under its North American limited lifetime warranty.
Since the rear springs on the 300 sit apart from the shocks, fitting these does not involve any spring compression. They make the most sense alongside B6 dampers at the front, so the car has a matched feel at both ends rather than a firm nose and a soft tail. Drivers who mainly want a quiet, cushioned ride on a commuter car may find a standard OE-style shock a closer match to what they expect.
View Bilstein B6 Performance 24-216951 Rear Pair on Amazon

5. Monroe Quick-Strut 471128L: Loaded Front Left Strut Assembly for 2011-2016 Chrysler Town & Country

- Listed for 2011-2016 Chrysler Town & Country
- Front left, fully assembled
- No spring compressor needed
- Coating tested against salt spray
The Monroe Quick-Strut 471128L is a loaded front strut for the left side of the 2011 to 2016 Chrysler Town & Country. The listing also fits several years of Dodge Grand Caravan and the 2011 to 2014 Volkswagen Routan, which share the van’s underpinnings. Monroe sells the right side under a separate number, 471128R, so buy both and swap them as a pair.
The assembly includes the strut, a coil spring matched to the application and a premium upper mount, all put together at the factory. Monroe states the spring is designed to restore ride height and carry the vehicle’s weight, and that the mount helps reduce noise and memory steer. The protective coating is salt spray tested, which helps on a van that spends winters on treated roads.
Minivans tend to rack up miles with heavy loads, and a tired front end shows up as a floaty highway ride, nose dive under braking and clunks over bumps. Because nothing needs to be compressed or transferred, this is a practical choice for a confident home mechanic with a jack and stands. It is meant to bring back the stock ride, not to change how the van handles.
View Monroe Quick-Strut 471128L on Amazon
6. Monroe OESpectrum 73155: Front Strut with Rod Displaced Valving for 2017-2023 Chrysler Pacifica

- Listed for 2017-2023 Chrysler Pacifica
- Also listed for 2020-2023 Voyager
- Rod displaced valving
- OE all-weather fluid
The Monroe OESpectrum 73155 is a front strut for the current-generation Chrysler Pacifica. Its feature list gives the fit as the 2017 to 2023 Pacifica and the 2020 to 2023 Voyager, while the title runs further, so treat the fit checker as the final word. Monroe also lists a companion Pacifica strut, 73156, so check which side each number covers, and note that hybrid or AWD vans may call for a different part.
OESpectrum is Monroe’s OE-style replacement line. This strut uses rod displaced valving tuned to the vehicle, which adjusts to rough and smooth pavement to keep the ride consistent. The damper is filled with an all-weather fluid that contains additives to cope with temperature extremes and slow oil breakdown, which is useful for a van that sees both hot summers and cold winter starts.
Expect a bare strut here rather than a loaded assembly. The Pacifica’s coil spring and top mount have to move from the old unit to the new one, so you need a spring compressor and the skill to use it safely, or a shop to handle that step. It suits owners who want an OE-like ride and prefer to keep a spring and mount that are still in good shape. If the springs have sagged, a complete assembly is the better route.
View Monroe OESpectrum 73155 on Amazon
Which Listing Fits Your Chrysler
Use this table as a shortlist of the best shocks and struts for Chrysler cars and minivans, then check the part against your VIN.
| Your Chrysler | Listing to check | Corner and type | Watch for |
|---|---|---|---|
| 2011 to 2020 300, stock ride | Monroe Quick-Strut 672665 | Front, loaded | Side not in the title; check the fit notes |
| 2005 to 2022 300 RWD, rear | Gabriel G51721 Ultra | Rear shock, single | RWD only; order two |
| 2011 and later 300, firmer control | Bilstein B6 24-326421 | Front left, bare | Needs a spring transfer |
| 2011 to 2014 300, rear upgrade | Bilstein B6 24-216951 pair | Rear shocks, pair | Mounting plates sold separately |
| 2011 to 2016 Town & Country | Monroe Quick-Strut 471128L | Front left, loaded | Buy the right side too |
| 2017 to 2023 Pacifica | Monroe OESpectrum 73155 | Front, bare | Hybrid and AWD may differ |

A noise from the front end does not always mean a failed strut. Chirps and creaks over speed bumps often come from dry sway bar bushings or worn end links, which our post on why a car squeaks when going over bumps helps you track down.
Grand Rapids Potholes, Road Salt and Worn Dampers
Freeze-thaw cycles open fresh potholes across Grand Rapids every spring, and a heavy sedan or loaded minivan hits each one hard. Over time the seals and valving wear out.
Watch for a second bounce after a dip, a nose that dips sharply under braking, cupped tire tread and oily streaks running down a strut body. A faint film of oil can be normal, but a wet, dirt-caked damper is leaking. Our walkthrough of how to tell if struts are bad covers the bounce test and the other checks in order.

Salt adds its own problem at replacement time. Lower strut bolts, top mount nuts and rear shock bolts often rust solid on a Michigan car, so soak them with penetrating oil a day ahead and have new nuts on hand. Monroe notes on its Quick-Strut assembly page that the units carry a protective coating checked with salt spray testing.
Fitting New Dampers and When a Shop Makes Sense
Loaded front struts and rear shocks are a fair driveway job with a floor jack and stands. Bare struts are where most home mechanics should stop, since the spring transfer is the risky step.
Whichever of the best shocks and struts for Chrysler models you choose, book a wheel alignment afterward. Removing a front strut disturbs camber and toe, and a car left out of spec pulls and wears its tire edges. If you are weighing brands, Bilstein’s North American warranty page lists B6 parts under its limited lifetime coverage.

If you would rather skip the seized hardware, our suspension repair service in Grand Rapids replaces struts, shocks, mounts and the steering parts around them. Hendrick Hoffman, who runs the shop, is ASE and State of Michigan certified in steering and suspension work, and his background is on our about us page.
More Buying Guides
Frequently Asked Questions
Are AWD Chrysler 300 struts the same as RWD struts?
Often not. The AWD front end uses different parts on many model years, so pick a listing that names your drive type and confirm it in Amazon’s fit checker with your year and engine.
Do Town & Country struts fit a Pacifica?
No. The Pacifica that arrived for 2017 has a different front suspension from the 2008 to 2016 Town & Country, so each van needs struts listed for that model.
Do the rear shocks need replacing at the same time as the front struts?
If all four have the same mileage, it is usually worth it. Fresh fronts paired with tired rears leave the back of the car bouncing, which shows up most with a full load of passengers or cargo.
Do I need an alignment after replacing Chrysler struts?
Yes. Taking a front strut out changes the wheel angles, so an alignment afterward keeps the car tracking straight and protects your tires.
Is your Chrysler bouncing, diving or knocking over Grand Rapids potholes? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a suspension inspection through our contact page.
Busy during the workday? Our after-hours drop-off at 456 Carrier St NE, Grand Rapids, lets you leave your Chrysler once we have closed for the day.
