As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A three-quarter-ton Ford that wallows after every expansion joint, or keeps bouncing long after a dip, is telling you its shocks have given up. Picking the best shocks for F250 Super Duty 4×4 trucks comes down to three questions: which generation you own, how high the truck sits and how hard it works.
Below are six Amazon listings sorted by model year and lift, most of which name the F-350 too. If the family car needs dampers as well, our roundup of shocks and struts for daily drivers covers that side of the driveway.
Quick answer
Which shocks should a four-wheel-drive F-250 Super Duty get?
Match the listing to your years and ride height. A Bilstein 4600 or Rancho RS5000X set suits a stock 2005 to 2016 truck, a FOX 2.0 set suits a stock 2017 to 2022 truck, and a Bilstein 5100 set suits a 2017 to 2024 truck with a 2 to 2.5 inch level.
Our Quick Picks
Three quick picks by year and ride height, with all six listings reviewed below. Confirm year, cab, engine and lift on Amazon before you buy.

Bilstein 4600 Set 24-185981 / 24-186674
Bilstein's factory-height line, sized for the coil-spring trucks.

FOX 2.0 Performance Set 985-24-151 / 985-24-154
A complete FOX set for unmodified or lightly leveled trucks.

Bilstein 5100 Set 24-274951 / 24-274968
Longer front shocks for the common 2 to 2.5 inch level.
Three Super Duty Front Ends, Three Sets of Part Numbers
Shock catalogs split the 4×4 Super Duty into clear groups. The Ford Super Duty history on Wikipedia notes that Ford moved the 4×4 trucks from front leaf springs to front coil springs for 2005, and moved the front sway bar from the axle to the frame at the same time.
- 1999 to 2004: a solid front axle on leaf springs. These trucks take their own front shocks, and the six listings below are written for 2005 and later trucks.
- 2005 to 2016: a solid front axle on coil springs and rear leaf springs, usually one fitment.
- 2017 and later: the aluminum-body truck, still on a solid front axle. Tremor models, added for 2020, sit higher from the factory and often take different front lengths.
On all of these trucks the shock is separate from the spring, so a swap needs no spring compressor. Front and rear lengths differ, so a “set” listing should show both part numbers.
Ride Height, Towing and Shock Design
Ride height decides shock length. A leveling kit lifts the nose about 2 inches and leaves a stock front shock near full extension, where it tops out over dips.
Next, think about the load: a diesel puts weight over the front axle, and a fifth-wheel trailer pushes hard on the rear. Monotube shocks keep the oil and gas apart and tend to hold their damping when they get hot, while twin-tube designs usually feel softer and closer to the original ride.
Best Shocks for F250 Super Duty 4×4: Six Listings by Year and Lift
Each listing states its own years, position and lift range. Enter your year, cab, engine and drive type in Amazon’s fit checker before you order.
1. Bilstein 4600 Series 24-185981 and 24-186674: Front and Rear Monotube Shocks for 2005-2016 F-250/F-350 Super Duty 4WD

- Listing names 2005-2016 F-250/F-350 Super Duty 4WD
- Stock-height replacement, front and rear part numbers
- Monotube body with high gas pressure
- Digressive valving for road and trail
This Bilstein listing pairs two 4600 Series part numbers, 24-186674 and 24-185981, and its compatibility line names the 2005-2016 F-250 and F-350 Super Duty 4WD, plus the 2008-2016 F-450. The 24-186674 is also sold on its own as a front shock, which makes the 24-185981 the rear half of the set. Check the quantity on the page so you know how many shocks arrive in the box.
The 4600 is the Bilstein range meant for trucks kept at factory height, and the listing calls it a stock height replacement. It describes a monotube design with high gas pressure, which helps the shock keep working when it heats up on a long tow or a washboard road. The valving is digressive, so the shock firms up quickly on sharp hits but stays fairly compliant over small ripples, a useful trait on a heavy diesel front end.
This set suits an owner refreshing a coil-spring Super Duty that has no leveling kit and no lift. It is not sized for a raised truck, and it does not cover the 1999-2004 leaf-spring trucks or anything from 2017 on. Enter your cab, bed and engine in the fit checker before you buy.
View Bilstein 4600 Set 24-185981 / 24-186674 on Amazon
2. Rancho RS5000X Gas Shock Set: Twin-Tube Front and Rear Shocks for 2005-2016 F-250 Super Duty 4WD

- Listing names 2005-2016 F-250 Super Duty 4WD, 0 inch lift
- Twin-tube body with all-weather fluid
- 16 mm nitro-carburized piston rod
- Polyvinyl protective boot fitted
The Rancho RS5000X listing is a shock set for the 2005-2016 F-250 Super Duty 4WD, and it states plainly that it is for trucks with no lift. That narrow fitment is a good thing, because it means the lengths match a factory-height coil-spring truck rather than a range of builds. Look at the quantity and part numbers on the page to confirm both axles are included.
Rancho builds the RS5000X as a large twin-tube shock filled with all-weather fluid, and it quotes an internal operating range of minus 40 to 248 degrees Fahrenheit. The listing names a 16 mm nitro-carburized piston rod to resist scuffs and corrosion, double-welded loops at the mounts and a 35 mm sintered iron piston. A polyvinyl boot covers the rod, which keeps road grit and salt spray off the seal. Rancho also describes progressive valving meant to soften the first impact at low speeds.
This set suits a stock Super Duty that spends most of its time on pavement, where the owner wants a ride close to how the truck felt new. A driver who tows heavy every week, or one with a leveling kit, should look at a monotube listed for that use instead. Confirm cab and engine in the fit checker first.
View Rancho RS5000X Set on Amazon

3. Bilstein 5100 Series 24-274951 and 24-274968: Front and Rear Monotube Shocks for 2017-2024 F-250/F-350 Super Duty 4WD with 2-2.5 Inch Level

- Listing names 2017-2024 F-250/F-350 Super Duty 4WD
- Sized for 2-2.5 inch front and 0-1 inch rear lift
- Tremor trucks listed at 0-2 inch front lift
- Velocity-sensitive digressive piston
This listing pairs Bilstein 5100 part numbers 24-274951 and 24-274968, and it names the 2017-2024 F-250 and F-350 Super Duty 4WD. The lengths are set for a truck with 2 to 2.5 inches of front lift and up to 1 inch at the rear. The listing adds a useful note for Tremor owners: on those trucks, the front shock fits with 0 to 2 inches of front lift, since the Tremor already sits higher.
Like other 5100 parts, these use a monotube body that Bilstein says gives consistent, fade-free damping, which counts on a truck pulling a heavy trailer up a long grade. The listing describes a velocity-sensitive, digressive piston that reacts to changing road surfaces, so the truck stays settled on rough pavement without feeling harsh on smooth roads. Bilstein’s limited lifetime warranty is also mentioned on the page.
This set suits a 2017 or later Super Duty wearing a typical leveling kit, especially one that tows or hauls often. On a truck at factory height these shocks run too long, and on a 4-inch lift they run out of travel. As always, check your trim, cab and Tremor status in the fit checker.
View Bilstein 5100 Set 24-274951 / 24-274968 on Amazon
4. FOX 2.0 Performance Series 985-24-151 and 985-24-154: Front and Rear IFP Shocks for 2017-2022 F-250 Super Duty 4WD

- Two front and two rear shocks in the set
- Listing names 2017-2022 F-250 Super Duty 4WD
- Stock to 1.5 inch front, up to 1 inch rear lift
- Washers, bushings, clamps and nuts included
The FOX 2.0 Performance listing ships two front and two rear shocks, part numbers 985-24-151 and 985-24-154, for the 2017-2022 F-250 Super Duty 4WD. It covers trucks with no suspension changes or up to 1.5 inches of front lift and 1 inch of rear lift. That makes it a good fit for an owner who has not touched the suspension, or one who added a small spacer up front.
On its 2.0 Performance Series page for the Super Duty, FOX describes an internal floating piston design that keeps the shock oil apart from the nitrogen gas, which stops the oil foaming on rough roads. The same page says the aluminum body boosts cooling and will never rust, a real plus under a truck that sees salted roads. Washers, bushings, reservoir clamps and nuts come in the box, and the factory mounting bolts are reused.
It fits the owner who wants all four corners done in one visit on a stock or mildly leveled truck. Shock boots, roost shields and mounting plates are sold separately. It is not meant for a 2 inch level or taller, which needs a FOX part number for that lift.
View FOX 2.0 Performance Set 985-24-151 / 985-24-154 on Amazon

5. Gabriel 77951 Max Control: Monotube Front Shock for 2005-2024 F-250 Super Duty 4WD

- Listing names 2005-2024 F-250 Super Duty 4WD
- 7.5 inch stroke, 20.5 inch extended length
- 13 inch collapsed length
- Monotube design for towing and hauling
The Gabriel 77951 is a front shock from the Max Control line, and its fitment list names the 2005-2024 F-250 Super Duty 4WD and F-350 Super Duty 4WD, along with older F-250 and F-350 models. The listing gives the key dimensions: a 7.5 inch stroke, a 20.5 inch extended length and a 13 inch collapsed length. Those figures make it easy to compare with the shock on your truck before you order.
Gabriel describes the Max Control as a monotube shock built for towing, hauling and light off-road use. The page lists upper and lower mount codes, S38 and ES34, and a long interchange list that includes Monroe and Rancho numbers, which helps when you are trying to identify what is fitted now. Because one part number spans so many years, the fit checker matters even more here, since trims and ride heights changed over that time.
This shock suits an owner whose front shocks are leaking or worn while the rears are still fine. Plan on two, one for each side of the axle, and check how many come in one order. It is sized for a stock truck, not for a leveled or lifted one.
View Gabriel 77951 Max Control on Amazon
6. Rough Country N3 23161_H: Front Shocks for 2005-2024 F-250/F-350 Super Duty with 2-4.5 Inch Lift

- Listing names 2005-2024 F-250/F-350
- Sized for 2 to 4.5 inches of front lift
- 54 mm nitrogen-charged body
- 10-stage variable valving
This Rough Country N3 listing, part 23161_H, covers front shocks for the 2005-2024 F-250 and F-350 with 2 to 4.5 inches of lift. That one range spans both the coil-spring trucks up to 2016 and the newer aluminum-body trucks, so confirm in the fit checker that it matches your year and drive type. Check the quantity on the page too, because some N3 listings ship as a single shock.
The Rough Country listing names a 54 mm body it says sheds heat quickly, plus nitrogen charging and 10-stage variable valving. The page also names rubber bushings, a spring-loaded piston rod seal and a 36 kN tensile strength. It quotes military-spec fluid rated for very cold temperatures, which matters for a diesel that cold-starts in a Grand Rapids January, though the page gives two different ratings, so take the exact figure loosely.
These shocks suit a Super Duty with a leveling kit or a mid-size lift where stock-length shocks would top out. They do not cover the rear, so pair them with rears sized for your rear lift. They are not for a truck at factory height.
View Rough Country N3 23161_H on Amazon
Matching Each Listing to Your Truck
The years and lift ranges in the chart come straight from each listing.
| Your truck | Ride height | Listing to check | Covers |
|---|---|---|---|
| 2005-2016 F-250 SD 4×4 | Factory height | Bilstein 4600 set or Rancho RS5000X set | Front and rear |
| 2005-2024 F-250 SD 4×4 | Factory height | Gabriel 77951 Max Control | Front only |
| 2017-2022 F-250 SD 4×4 | Stock to 1.5 inch front | FOX 2.0 Performance set | Front and rear |
| 2017-2024 F-250 SD 4×4 | 2 to 2.5 inch front level | Bilstein 5100 set | Front and rear |
| 2005-2024 F-250 SD 4×4 | 2 to 4.5 inch lift | Rough Country N3 23161_H | Front only |

Always change shocks in axle pairs. A creak over driveway aprons, though, is often a dry bushing or sway bar link, and our article on why a car squeaks when going over bumps helps you narrow it down first.
Salt, Seized Hardware and Front-End Shake
After a few West Michigan winters, Super Duty shock bolts are often rusted into their sleeves. Soak them with penetrating oil the night before and keep spare bolts and nuts handy.
Worn shocks show up as extra bounce, nose dive, cupped tires and oil on the body. Our walkthrough on how to tell if struts are bad explains the bounce test and the leak check, and both work on shocks.

New shocks will not cure the violent shake that solid-axle Ford owners call death wobble. That usually starts with a worn track bar, loose ball joints or tired steering joints, so read our guide to bad tie rod symptoms and have a helper rock the steering wheel while you watch the linkage.
Doing the Swap at Home or Bringing It In
A shock change on an F-250 is a reasonable driveway job with the right gear. These trucks are heavy, so support the frame on jack stands rated for full-size trucks and keep the axle from hanging on its brake hoses.

The shocks themselves do not move the alignment, but a leveling kit or lift does. Book an alignment whenever the ride height changes, even with the best shocks for F250 Super Duty 4×4 trucks fitted, or the tire edges will wear fast.
If you would rather hand over the keys, our suspension repair service in Grand Rapids can fit the shocks and check the track bar, ball joints and steering linkage at once. Hendrick Hoffman, who runs the shop, carries ASE and State of Michigan credentials covering steering and suspension work; read more on our about us page.
More Buying Guides
Frequently Asked Questions
Do the F-250 and F-350 Super Duty 4×4 take the same shocks?
Often, yes. Several listings here name both trucks for the same years, but some split by trim, cab or rear wheel setup. Enter your exact truck in Amazon’s fit checker and read any qualifier notes before you order.
Does a diesel F-250 need different shocks than a gas truck?
Most shock listings go by year, drive type and lift rather than engine, so the part number is often the same. The diesel’s extra weight up front is a good reason to favor a monotube, though, especially if you tow.
Which is the better fit, the Bilstein 4600 or the 5100?
The 4600 is Bilstein’s factory-height line, so it suits a stock truck. The 5100 sets in this guide are valved and sized for leveled trucks, with a stated front lift range for each generation.
Will new shocks stop death wobble on my Super Duty?
No. Fresh shocks can make it show up less often, but the cause is almost always a loose track bar, ball joint or steering joint. Find and repair the worn part first, then replace the shocks if they are tired too.
Is your Super Duty bucking over frost heaves or diving every time you brake with a trailer behind it? Phone 456 AutoFix at 616-279-3832 on a weekday between 8am and 5pm, or schedule a suspension check on our contact page.
Tied up at work until closing time? Bring the truck to 456 Carrier St NE, Grand Rapids, MI 49505 whenever it suits you and use the after-hours drop-off, and we will take it from there.
