456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Stock or Leveled: Choosing the Best Shocks for Ram 2500 Trucks, 2014 and Later

best shocks for ram 2500: road curving through a green valley at dusk

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A three-quarter-ton Ram with worn dampers lets you know on every expansion joint: the nose nods and the bed hops over patched pavement. Choosing the best shocks for Ram 2500 trucks built from 2014 on comes down to three things, the drive type, the ride height and how hard the truck works.

This guide covers 2014 and later trucks, gas or Cummins diesel. For lighter vehicles, see our guide to shocks and struts for daily drivers.

Quick answer

Which shocks should a 2014 or newer Ram 2500 get?

Match the shock to the ride height. A stock-height 4WD truck suits a Bilstein 4600 front pair or a FOX 2.0 set. A truck leveled 2 to 2.5 inches needs the longer Bilstein 5100 or Rancho RS5000X listings. Check drive type, air rear suspension and trim in Amazon’s fit checker first.

Our Quick Picks

Three quick picks: a Bilstein 4600 front pair for stock-height 4WD trucks, a Bilstein 5100 front pair for leveled trucks and a FOX 2.0 set that renews all four corners. All six listings are reviewed below.

Bilstein B6 4600 Front Pair product photo
Stock height

Bilstein B6 4600 Front Pair

Front pair · 2014-2019 Ram 2500 4WD

Factory-height monotube shocks for the front axle.

SuitsOwners keeping the factory stance
View on Amazon →
Bilstein 5100 Front Pair product photo
Leveled front

Bilstein 5100 Front Pair

Front pair · 2014-2018 Ram 2500, 2-2.5 in

Longer monotube shocks sized for a leveled nose.

SuitsTrucks with a leveling kit
View on Amazon →
FOX 2.0 Performance Set product photo
Full set

FOX 2.0 Performance Set

Front and rear · 2014-2022 Ram 2500 4WD

Four FOX shocks for stock or slightly raised trucks.

SuitsOwners renewing all four corners
View on Amazon →

Know Your Ram 2500 Before You Shop

The 2014 model year brought a coil-spring rear end to the Ram 2500, so the shocks for these trucks differ from the leaf-spring Dodge era. Most 4WD trucks run a solid front axle on coil springs with a shock at each corner. That makes this a shock job front and rear, with no struts and no spring compression involved.

  • Drive type: 4WD and 2WD trucks use different front shock lengths, and most listings name one or the other.
  • Rear air suspension: trucks with the factory auto-level rear are excluded by many listings, so check that line.
  • Power Wagon and Rebel: these trims leave the factory with their own Bilstein shocks and a different ride height.
  • Model year: some listings stop at 2018 or 2019, others run into the 2020s.

Ram’s own Ram 2500 model page lists a Bilstein shock system on the Power Wagon and Bilstein gas-charged monotube shocks on the Rebel. A listing written for a Tradesman or Big Horn may not match those trucks. Gas or diesel matters less than people expect, since most listings key on drive type and lift, but the fit checker still has the final word.

Ride Height Decides the Shock Length

A shock has a set collapsed and extended length. When a truck is leveled, the front axle hangs farther from the frame, and a stock-length shock can run out of travel and top out on rebound. That is why lift height appears in nearly every listing title below.

  • Stock height: factory-length shocks such as the Bilstein 4600, or sets rated for up to about 1.5 inches.
  • Leveled 2 to 2.5 inches: longer front shocks such as the Bilstein 5100 or the Rancho set made for that range.
  • Taller lifts: longer shocks again, usually sold with or matched to the lift kit.

Body design matters too. A monotube shock keeps its gas in a separate chamber and tends to shed heat well while towing, while a twin-tube shock is the common factory-style design.

Best Shocks for Ram 2500: Six Listings by Ride Height

Each pick names the years, drive type and lift range its own listing states. No single part fits every 2014 and later Ram 2500, so enter your year, cab, drive type and trim in Amazon’s fit checker and read the exclusions before you order.

1. Bilstein B6 4600 24-240390: Front Monotube Shock Pair for 2014-2019 Ram 2500 4WD

Bilstein B6 4600 Front Pair product photo
Key features
  • Listed for 2014-2019 Ram 2500 4WD
  • Part number 24-240390, front pair
  • Monotube gas design for stock height
  • Bilstein limited lifetime warranty

The Bilstein B6 4600 is the brand’s line for trucks that stay at factory ride height, and this listing bundles two front shocks, part number 24-240390, for the 2014 to 2019 Ram 2500 4WD. It is a front-axle purchase only, so the rear shocks are a separate order if they are worn too. Enter your cab, trim and suspension in Amazon’s fit checker, because Power Wagon trucks and some lifted builds use different lengths.

The 4600 uses a monotube body with a gas charge, which keeps the oil and gas apart and gives the shock a large working piston. The listing notes that each shock includes only the lower spring mount and no other hardware, so plan to reuse good factory bolts or buy new ones if salt has eaten them. Bilstein backs the line with a limited lifetime warranty.

This pair suits a work truck or daily driver that never got a leveling kit and has started to float or nod on the highway. It is not the right length for a truck leveled 2 inches or more, where the shock can run short on rebound. In that case look at the 5100 listing below.

View Bilstein B6 4600 Front Pair on Amazon

2. Bilstein 5100 Front Shock Pair: Monotube Gas Shocks for 2014-2018 Ram 2500 with 2-2.5 Inch Lift

Bilstein 5100 Front Pair product photo
Key features
  • Listed for 2014-2018 Ram 2500, 2-2.5 in lift
  • Two front shocks in the box
  • Digressive, velocity-sensitive piston
  • Limited lifetime warranty

The Bilstein 5100 is the brand’s line for trucks with a modest lift, and this front pair is listed for the 2014 to 2018 Ram 2500 in 2WD or 4WD form with a 2 to 2.5 inch front lift. One feature bullet says it fits 2014 to 2017 trucks, so a 2018 owner should confirm fit with Amazon’s checker before ordering. The box holds two shocks, which covers the front axle.

The listing gives a collapsed length of 15.03 inches and an extended length of 22.63 inches, longer than a factory-height shock, so the front axle can droop on a leveled truck without topping out. Bilstein describes the 5100 as tuned for each application, with a velocity-sensitive digressive piston that reacts to changing road conditions. A limited lifetime warranty applies.

Pick this pair if you have leveled the front of your Ram 2500 or plan to, and you want shocks made for that height. It is not meant for a truck at factory height, where the longer body may not suit the mounts. Plan an alignment after any leveling work, since the change in front height moves caster and toe.

View Bilstein 5100 Front Pair on Amazon

road switchbacks across a green valley

3. FOX 2.0 Performance 985-24-168 and 985-24-169: Front and Rear Shock Set for 2014-2022 Ram 2500 4WD

FOX 2.0 Performance Set product photo
Key features
  • Listed for 2014-2022 Ram 2500 4WD
  • Two front and two rear shocks
  • Stock height to 1.5 in lift
  • Washers, bushings and nuts included

This FOX 2.0 Performance listing is a full set of four shocks for the 2014 to 2022 Ram 2500 4WD, built around part numbers 985-24-168 for the front and 985-24-169 for the rear. According to the listing, it covers trucks with no suspension modifications or up to 1.5 inches of lift at either end. That makes it a one-order refresh for a stock or lightly raised truck.

The set comes with the washers, bushings, reservoir clamps and nuts needed for installation, while the factory shock mounting bolts are reused. Shock boots, roost shields and mounting plates are sold separately if you want them. FOX covers the set with a one-year warranty, which is shorter than the lifetime coverage several other brands here offer.

This set suits an owner whose truck has high miles on the original shocks at both ends and who wants front and rear damping matched by one maker. It is listed for 4WD trucks only, so 2WD owners need a different part. It does not fit a 2 to 2.5 inch leveled front, which needs longer shocks like the Bilstein 5100 or Rancho set.

View FOX 2.0 Performance Set on Amazon

4. Rancho RS5000X Gas Shock Set: Front and Rear Twin-Tube Shocks for 2014 Ram 2500 4WD with 2.5 Inch Lift

Rancho RS5000X Shock Set product photo
Key features
  • Listed for Ram 2500 4WD with 2.5 in lift
  • Coil rear spring trucks only
  • 16mm nitro-carburized piston rod
  • Fluid rated -40 to 248°F internally

Rancho’s RS5000X is a twin-tube performance shock, and this listing is a front and rear set titled for a 2014 Ram 2500 4WD with a 2.5 inch lift. Its compatibility bullet goes further, naming 2014 to 2024 Big Horn, Laramie and Tradesman trucks and other trims with a coil rear spring. With the title and bullet differing, confirm your year and trim in Amazon’s fit checker before you buy.

Rancho lists Cross Tuned valving with its own rebound system and Progressive Engagement Valving meant to soften low-speed impacts. The shock uses a 16mm nitro-carburized piston rod to resist scuffs and corrosion, double-welded loops at stress points and a protective boot over the rod. A large twin-tube body with all-weather fluid is rated to handle internal temperatures from -40 to 248°F.

This set suits a leveled 4WD truck whose owner wants all four corners matched to the lift in a single order. The boots are a plus on salted Michigan roads, where grit and spray attack exposed rods. It is not meant for a stock-height truck or one with the rear air suspension, which needs different shocks.

View Rancho RS5000X Shock Set on Amazon

red hatchback parked in a dark meadow

5. Rough Country N3 23193_F: Front Shocks for 2014-2024 Ram 2500 4WD with 0-1.5 Inch Lift

Rough Country N3 Front Shocks product photo
Key features
  • Listed for 2014-2024 Ram 2500 4WD
  • For 0 to 1.5 in of lift
  • 10-stage variable valving
  • 54mm nitrogen-charged body

Rough Country’s N3 is the brand’s nitrogen-charged twin-tube shock, and part number 23193_F is the front shock for the 2014 to 2024 Ram 2500 4WD with zero to 1.5 inches of lift. The wide year range is useful for owners of 2019 and later trucks, since several other front listings here stop at 2018 or 2019. Check the listing for whether you receive one shock or a pair, and buy enough for both sides.

The listing describes 10-stage variable valving, rubber bushings and a 54mm shock body that helps the shock cool. It also notes a spring-loaded piston rod seal and military-spec fluid rated for very cold temperatures, which matters on January mornings in West Michigan. Rough Country backs the N3 with a limited lifetime replacement warranty.

These shocks suit a later truck that sits at factory height or carries a small spacer, where the owner wants fresh front damping without changing the stance. They are not meant for a 2 to 2.5 inch leveled front, which Rough Country covers with a separate, longer part. Pair them with matching rears if the original rear shocks are tired.

View Rough Country N3 Front Shocks on Amazon

6. Monroe Gas-Magnum 34534: Heavy-Duty Twin-Tube Shock Absorber for 2014-2024 Ram 2500

Monroe Gas-Magnum 34534 product photo
Key features
  • Compatibility lists 2014-2024 Ram 2500
  • Sold as a single shock
  • Nitrogen gas charge, 2 in reserve tube
  • Limited lifetime warranty

Monroe’s Gas-Magnum line is built for full-size trucks and vans, and part number 34534 lists 2014 to 2024 Ram 2500 trucks across several year ranges, plus the 2013 to 2024 Ram 3500. The listing sells one shock and does not name the axle position in its title, so use the Amazon Confirmed Fit bar and its notes to confirm whether it suits the front or rear of your truck. Buy two for the axle you are servicing.

Monroe describes full-displaced valving on the compression stroke, a heavy-duty nitrocarburized rod and a sintered iron piston. A larger bore and a 2 inch reserve tube hold more oil, and the nitrogen gas charge is meant to reduce aeration and fade. OE all-weather fluid with friction modifiers handles temperature swings, and Monroe adds a limited lifetime warranty.

This shock suits a stock-height work truck where the goal is to restore a factory-style ride rather than change the stance. It is a twin-tube design, so it may not shed heat as quickly as a monotube on long rough-road runs with a heavy trailer. Leveled and lifted trucks should look at the longer listings above.

View Monroe Gas-Magnum 34534 on Amazon

Which Listing Fits Your Truck

The best shocks for Ram 2500 owners are the ones listed for their exact truck. Find your row, then confirm the part number on Amazon.

Your Ram 2500Listing to checkCoversWatch for
2014 to 2019 4WD, stock heightBilstein B6 4600 24-240390Front pairRear shocks sold separately
2014 to 2018, leveled 2 to 2.5 inchesBilstein 5100 front pairFront pairBullet lists 2014 to 2017
2014 to 2022 4WD, up to 1.5 inchesFOX 2.0 Performance setFront and rearOne-year warranty
2014 and later 4WD, 2.5 inch liftRancho RS5000X setFront and rearCoil rear spring only
2014 to 2024 4WD, up to 1.5 inchesRough Country N3 23193_FFrontCheck quantity in listing
2014 and later, stock replacementMonroe Gas-Magnum 34534Single shockConfirm front or rear
Ram 2500 shock listings compared by years, ride height and what each one includes
black and white photo of worn hands

Before you blame the shocks for every noise, rule out the cheaper parts around them. A squeak over speed bumps often comes from dry bushings or sway bar links, and our article on why a car squeaks when going over bumps walks through the usual suspects.

Towing, Salt and Michigan Potholes

When you shop for the best shocks for Ram 2500 towing, remember what dampers can and cannot do. Fresh dampers help settle bounce and porpoising, but they do not add payload or towing capacity, so stay within the ratings on your door sticker.

Grand Rapids freeze-thaw season fills the roads with potholes, and a heavy truck lands hard in every one. Watch for a nose that keeps bouncing after a dip, cupped tire wear, oil streaks down the shock body and extra body roll on ramps. Our guide on how to tell if struts are bad explains these signs, and they apply to shocks as well.

multi-tool on a red cloth

Road salt is the other enemy. Lower shock bolts on Michigan trucks can rust into their sleeves and upper nuts round off, so have new hardware on hand.

Fitting the Shocks Yourself or at Our Shop

Shocks on these trucks are a reasonable driveway job with jack stands, wheel chocks and good sockets. Because the coil springs stay on the truck, you do not need a spring compressor; save the coil spring compressor guide for strut work on other vehicles. Always replace shocks in pairs on the same axle so both sides damp evenly.

Rancho’s installation tips advise spraying old bolts with penetrant, torquing the hardware with the suspension loaded and getting an alignment after a lift or leveling kit. A straight shock swap at stock height does not change alignment, but leveling the front does.

highway at sunset

If you would rather hand the job over, our suspension repair team in Grand Rapids replaces shocks, struts and the steering parts that wear alongside them. Hendrick Hoffman has worked in automotive service since 2005 and is ASE and State of Michigan certified in steering and suspension, as the about us page details.

Frequently Asked Questions

Should I choose the Bilstein 4600 or 5100 for my Ram 2500?

Choose by ride height. The 4600 front pair here is listed for a 2014 to 2019 4WD truck at factory height. The 5100 front pair is listed for trucks leveled 2 to 2.5 inches, so it suits a leveling kit.

Does a Cummins Ram 2500 need different shocks than a gas truck?

Usually the listings key on drive type, years and lift rather than engine. The diesel adds weight over the front axle, though, so enter your engine and trim in the fit checker and read any notes before you buy.

Do I need an alignment after replacing Ram 2500 shocks?

Not for a like-for-like swap at stock height, since shocks do not set the truck’s geometry. If you level or lift the front at the same time, plan an alignment to bring caster and toe back into spec.

Can I replace only the front shocks?

Yes, as long as you replace both shocks on that axle. If the rears are original on a high-mileage or towing truck, doing all four keeps the ride balanced front to rear.

Ram 2500 bucking over every seam or wandering with a trailer behind it? Ring 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a shock inspection through our contact page.

Working the same hours we are? Park the truck at our Creston shop, 456 Carrier St NE, after closing and drop the keys through our after-hours service.