As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A square-headlight Jeep was never a soft ride, but a YJ that hops sideways over washboard roads or keeps bobbing after a dip has usually worn past its shocks. The best shocks for YJ Wrangler owners are the ones sized to the Jeep’s ride height, because a stock 1987 Sahara and a 1994 on a 4 inch spring lift need very different lengths.
This guide sticks to the 1987-1995 Wrangler YJ. If you are still deciding whether the dampers are to blame, start with our guide on signs your shocks or struts are worn out.
Quick answer
Which shocks suit a 1987-1995 Jeep Wrangler YJ?
At factory height, the Rancho RS5000X YJ set or a Monroe OESpectrum 37120 gives a fresh, OE-style ride. A Jeep with up to 3 inches of lift can run Rough Country N3 23148_A fronts. On a 3-4 inch lift, the Bilstein 5100 24-064576 front pair is sized for that height.
Our Quick Picks
Three listings for a stock YJ, a mild lift and a 3-4 inch build. Confirm your year, position and lift on Amazon.

Rancho RS5000X YJ Set
One box covers both axles on an unlifted YJ.

Rough Country N3 23148_A
Front shocks sized for a stock to lightly lifted YJ.

Bilstein 5100 24-064576
Bilstein front shocks sized for a common YJ lift height.
How the YJ Is Built Underneath
The YJ rides on leaf springs at both axles, much like the CJ it replaced, with wider springs and a track bar added to locate the axles. The Wikipedia entry on the Wrangler YJ also notes there was no 1996 model year, so the last YJ parts listings end at 1995 even when a few say 1996.
Because the springs are leaves, every shock on a YJ is a separate bolt-on part. No spring has to come apart, so you will not need the kind of tool covered in our coil spring compressor buying guide. That tool only matters if the Jeep has been converted to coils or you also own a later coil-sprung Wrangler.
- Height first: stock, 0-3 inch, 3-4 inch and taller lifts each take their own lengths.
- Axle second: front and rear shocks carry different part numbers.
- Spring-over builds: a spring-over-axle swap needs shocks listed for it, not the regular lift parts.
- Years: the listings below name 1987-1995, so check your VIN year matches.
Reading a Shock Listing Before You Order
Most OE-style YJ replacements are twin-tube shocks, with the working piston inside one tube and spare oil held in an outer tube. The Bilstein 5100 is a monotube, a single wider tube with the gas charge kept apart from the oil. Twin-tube shocks tend to suit a commuter Jeep, while lifted rigs that see trails often get monotube or larger-bodied shocks.
Every serious listing gives an extended and collapsed length. On a lifted YJ, put the axle at normal ride height, measure from the upper mount to the lower mount and check that figure sits near the middle of the shock’s travel. A shock that runs out of stroke on full droop pulls hard on its mounts, and one that bottoms out internally takes the hit instead of the bump stop.
Best Shocks for YJ Wrangler: Six Listings by Ride Height
Each listing below names the YJ in its own words, along with the position or lift it was made for. Treat the list as a starting point and run your Jeep through Amazon’s fit checker, since no single part number covers every YJ build.
1. Rancho RS5000X Gas Shocks Set: Four Twin-Tube Shocks for 1987-1995 Wrangler YJ 4WD

- Set listed for 1987-1995 Wrangler YJ 4WD
- Fit note names 0-1.5 inch lift
- 16mm nitro-carburized rod, 35mm piston
- All-weather fluid in a twin-tube body
The Rancho RS5000X set bundles front and rear gas shocks for one Jeep, so you avoid chasing four separate part numbers. Its Amazon listing names the 1987-1995 Wrangler YJ 4WD, and the fit note in the bullets covers a YJ from factory height up to a 1.5 inch lift. That makes it a direct choice for a Jeep that still sits on its original springs or a mild leaf refresh.
Rancho calls the RS5000X a Cross Tuned twin-tube shock, meaning its rebound valving and compression stage are tuned together. The maker says its progressive engagement valving is set for each vehicle to take the sting out of low-speed bumps. Each shock uses a 16mm nitro-carburized piston rod, a 35mm sintered iron piston, double-welded loops at the stress points and a polyvinyl boot to keep dirt off the rod, and Rancho rates the fluid from -40 to 248°F.
This set fits owners who drive a YJ to work most days and take it down two-tracks on weekends. It is not sized for a 3 inch or taller lift, where the shocks would run short. Check the listing photos for what comes in the box and confirm your Jeep in Amazon’s fit checker.
View Rancho RS5000X YJ Set on Amazon
2. Monroe OESpectrum 37120: OE-Style Replacement Shock for 1987-1995 Jeep Wrangler

- Listed for 1987-1995 Jeep Wrangler
- Twin-tube with nitrogen gas charge
- PTFE-banded piston for steady sealing
- Sold as a single shock
The Monroe OESpectrum 37120 is a single replacement shock that its Amazon listing ties to the 1987-1995 Jeep Wrangler. It is built to bring back a factory-style ride rather than change how the Jeep handles. The title does not state front or rear, and Monroe sells the 37121 as the other YJ position, so read the position in Amazon’s fit notes before you order two of the same number.
Monroe describes full displaced valving tuned to each vehicle, paired with a larger bore that the maker says gives more efficient damping. A PTFE-banded piston keeps a consistent seal against the pressure tube, and a nitrogen gas charge is there to cut aeration and fade on long rough stretches. Monroe also lists an all-weather fluid with additives for extreme temperatures and a self-lubricating seal that limits friction on the piston rod.
This shock suits a stock-height YJ whose owner wants a quiet, familiar ride on pavement and gravel. It is not sold for lifted Jeeps, and because it comes one at a time, you need two per axle. Buy matching pairs and confirm the year and position on Amazon before checkout.
View Monroe OESpectrum 37120 on Amazon

3. Rough Country N3 23148_A: Front Shock Pair for 1987-1995 Wrangler YJ with 0-3 in Lift

- Front shocks for 87-95 Wrangler YJ
- Sized for 0-3 inch of lift
- 10-stage variable valving
- 54mm body, nitrogen charged
Rough Country lists the N3 23148_A as front shock absorbers for the 1987-1995 Jeep Wrangler YJ with 0 to 3 inches of lift. That range covers a stock Jeep, a set of slightly taller replacement leaves or a budget 2.5 inch kit. It is a front-only part, so pair it with a rear shock sized to the rear ride height of your own Jeep.
The maker lists 10-stage variable valving, a nitrogen charge and a 54mm shock body that it says sheds heat quickly. Rough Country quotes 36kN tensile strength, rubber bushings and a spring-loaded piston rod seal, along with a fluid it rates for very cold use. That cold rating is worth noting for a Jeep that sits outside through a Michigan January and still has to work on the first start.
This shock suits a YJ that mixes commuting with trail days at a small lift. A bigger lift calls for a longer part number, such as Rough Country’s 3.5-6 inch fronts. Measure your ride height, compare it with the extended length on the listing and confirm fit on Amazon before you order.
View Rough Country N3 23148_A on Amazon
4. Bilstein 5100 24-064576: Front Monotube Shock Pair for 87-96 Wrangler YJ 4WD with 3-4 in Lift

- Front pair, part number 24-064576
- For 4WD YJ with 3-4 inch front lift
- Monotube gas shock design
- Washers, bushings and nuts included
The Bilstein 5100 24-064576 is sold as a front pair for the Jeep Wrangler YJ 4WD with 3 to 4 inches of front lift. The listing title says 87-96, but there was no 1996 model year Wrangler, so treat it as a 1987-1995 YJ part. For the rear of the same Jeep, Bilstein lists the 24-185660 for a 3-4 inch rear lift.
The 5100 is a monotube design, with the oil and gas held apart in one wide tube rather than a twin-tube layout. The listing states that all washers, bushings and nuts come in the box and that the factory shock bolts are reused. That keeps the job to the shocks themselves, though rusty lower studs on an older YJ can still add time.
This pair suits a lifted YJ that sees trail use on weekends and highway miles in between. It is the wrong length for a stock Jeep, where it would sit too long, and for a 6 inch build, where it would run short. Measure your ride height and confirm fit on Amazon before buying, and plan an alignment check after the lift itself.
View Bilstein 5100 24-064576 on Amazon

5. Gabriel Ultra G63490: Rear Twin-Tube Shock for 1987-1995 Jeep Wrangler YJ

- Rear shock, 87-95 Wrangler YJ
- Extended 19.08 in, collapsed 12.05 in
- 7.03 inch stroke
- Interchanges with Monroe 37121
The Gabriel Ultra G63490 is a single rear shock that its Amazon listing fits to the 1987-1995 Jeep Wrangler YJ, along with the 1986-1988 Ford Aerostar RWD. It is a premium OE-style replacement rather than a lift part. The listing is unusually complete on dimensions, which helps if your YJ has had new springs and you want to check lengths against the mounts.
Gabriel gives a 19.08 inch extended length, a 12.05 inch collapsed length and a 7.03 inch stroke, with EB1 upper and ES25 lower mount codes. The interchange list includes Monroe 37121 and Rancho RS5113, which helps if you are matching an older receipt. Gabriel describes a precision twin-tube design meant for a smooth ride and good handling under normal driving conditions.
This shock suits a stock-height YJ that needs its rear end calmed down over potholes, frost heaves and expansion joints. Its normal driving brief makes it a poor fit for a rock-crawling rig or a lifted Jeep. It is sold one at a time, so buy two for the rear axle and confirm your model year on Amazon before checkout.
View Gabriel Ultra G63490 on Amazon
6. Rancho RS9000XL Set: Adjustable Shocks for 1987-1995 Wrangler YJ 4WD, 0-2.5 in Front Lift

- Part numbers RS999118 and RS999168
- Front: factory height to 2.5 inch lift
- Rear: for 2.5 inch lift, Rancho 2.5 in system
- Adjustable damping, set of four
The Rancho RS9000XL set brings four adjustable shocks for the 1987-1995 Wrangler YJ 4WD, using part numbers RS999118 and RS999168. Its listing says the set suits a Jeep at factory height or with up to 2.5 inches of front lift, paired with a 2.5 inch rear lift from Rancho’s 2.5 inch system. Read that rear note closely, because a fully stock rear may call for a different part number.
The RS9000XL is Rancho’s adjustable line, so you can change the damping setting on each shock rather than living with one fixed feel. That lets one Jeep run firmer for a loaded trip and softer for a washboard road. The listing states that all washers, bushings and nuts are included, factory shock bolts are reused, and Rancho’s 90-day ride guarantee covers the RS9000XL.
This set suits YJ owners running the Rancho 2.5 inch system who want to tune the ride for both trail and road use. It is more than a plain stock commuter needs, and the rear sizing assumes a lift. Confirm your exact setup and model year in Amazon’s fit checker before ordering the set.
View Rancho RS9000XL YJ Set on Amazon
Matching Each Listing to Your Jeep
The table lines up the best shocks for YJ Wrangler builds by the height and position each listing states. Use it to narrow the field, then confirm the exact part on Amazon before you buy.
| YJ setup (1987-1995) | Front | Rear |
|---|---|---|
| Factory height, daily use | Monroe OESpectrum 37120, or the Rancho RS5000X set | Gabriel Ultra G63490, or the Rancho set |
| Factory height, adjustable feel | Rancho RS9000XL set (RS999118) | Rancho RS9000XL set (RS999168, for 2.5 inch rear lift) |
| 0-3 inch lift | Rough Country N3 23148_A | Match the rear to its own lift height |
| 3-4 inch lift | Bilstein 5100 24-064576 | Bilstein 24-185660 is the matching rear part number |
Swap shocks in pairs on each axle so one side does not damp harder than the other. On a YJ with an unknown history, a full set of four is the simpler choice, since mismatched brands front to rear can make the short wheelbase feel even busier.

Salt, Frost Heaves and Thirty-Year-Old Bushings
Michigan road salt is hard on an old Jeep frame, and the lower shock studs on a YJ axle are often rusted solid. Spray them with penetrating oil the night before and have a replacement nut and a cutting wheel ready. Spring frost heaves and potholes around Grand Rapids then finish off any shock that was already weak.
The AA1Car ride control diagnosis article points out that short-wheelbase SUVs with truck-style suspension often ride choppy even with healthy shocks, which describes the YJ well. It suggests a bounce test: rock each corner and let go, and if the body keeps moving for more than one or two cycles, the damper is done.

Not every noise is a shock. Dry shackle bushings and sway bar links squeak, as our article on squeaking over speed bumps describes, and a front-end clunk can come from worn joints, covered in our Jeep ball joint roundup. A YJ that sags on one side has tired leaves, and new shocks will not lift it back up.
Garage Job or Shop Visit
With the Jeep on jack stands and the axle supported, a YJ shock change is mostly a matter of breaking loose rusty hardware. Keep the axle from hanging on its brake hoses, and torque the mounts with the Jeep back on its wheels. If you also keep a newer car in the driveway, our list of shocks and struts for everyday commuters covers sedans and crossovers.

New shocks on their own do not move the alignment, but a lift kit or fresh leaf springs change caster and steering geometry, so book an alignment after that work. Even the best shocks for YJ Wrangler Jeeps cannot cover for a loose track bar or worn tie rod ends. Our Grand Rapids suspension repair service can look over the whole front end, and owner Hendrick Hoffman is ASE and State of Michigan certified in steering and suspension work.
More Buying Guides
Frequently Asked Questions
Do TJ shocks fit a YJ Wrangler?
Not as a rule. The TJ that replaced it moved to coil springs and different mounts, so its shocks have other lengths and part numbers. Buy shocks that name the 1987-1995 YJ.
What shocks does a YJ with a 4 inch lift need?
Look for shocks listed for that height, such as the Bilstein 5100 24-064576 front pair for a 3-4 inch lift. Stock-length shocks run out of travel on a lifted YJ and can top out on full droop.
Can I change YJ shocks without a spring compressor?
Yes. The YJ uses leaf springs at both ends, so each shock unbolts on its own while the springs stay where they are.
Will new shocks stop death wobble on a YJ?
Usually not. A violent shake after a bump tends to come from worn steering parts, a loose track bar or ball joints. A fresh steering stabilizer can hide the symptom, so have the front end checked first.
YJ bouncing down the road or skittering over every crack? Phone 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or request a suspension inspection on our contact page.
Need the Jeep during business hours? Bring it to 456 Carrier St NE, Grand Rapids, MI 49505 after work and use our after-hours drop-off.
