As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
The new tie rod end is in the box, the castle nut is off, and the old stud still will not budge from the knuckle. The best tie rod end puller for that moment is the one that matches how the joint is built, how much room you have around it and whether you plan to reuse the part you are pulling.
This guide sorts the main tool designs, then reviews five specific tools for outer ends, inner tie rods and general front end work. If you are still deciding whether the joint is worn at all, start with our guide to bad tie rod symptoms.
Quick answer
Which tie rod end puller should a home mechanic buy?
For outer tie rod ends on most cars and light trucks, a screw-type jaw puller such as the Performance Tool W80557 is the safest first buy. Add a pickle fork set when the old part is scrap, and an inner tie rod tool like the Lisle 58100 if the rack-side joint is worn too.
Our Quick Picks
Three quick picks for outer tie rod ends, mixed front end work and inner tie rods. All five tools are reviewed below.

Performance Tool W80557
A controlled screw puller that frees the taper without tearing the boot.

OMT 5-Piece Front End Kit
Several jaw sizes and styles in one case for mixed front end jobs.

Lisle 58100
Reaches the rack-side joint without pulling the steering rack.
Why a Tie Rod End Sticks in the Knuckle
An outer tie rod end has a tapered stud that drops into a matching tapered hole in the steering knuckle or spindle arm. When the nut is torqued, the two tapers lock together so tightly that the stud stays put even with the nut removed. Rust between the surfaces makes that bond stronger every winter.
The inner tie rod is a different joint. It threads onto the end of the steering rack under a rubber bellows, so it has no taper to break, but it often sits where an ordinary wrench cannot reach its flats. That is why a full tie rod job can call for two kinds of tool, and trucks with a steering box add pitman arm joints that the same jaw pullers often handle.
Jaw Puller, Wedge or Pickle Fork: Picking a Design
A jaw puller hooks a forged yoke under the knuckle and drives a forcing screw down onto the stud tip. The pressure is steady, so the boot and threads survive, which matters if the joint is staying on the car.
A pickle fork is a tapered wedge you drive between the knuckle and the tie rod end with a hammer. It is quick and works on badly rusted joints, but it nearly always tears the dust boot, so save it for parts headed to the scrap bin. A screw-driven wedge sits between the two parts and spreads them apart with less shock and less damage.
Whichever design you choose, look for a forged yoke or body and a heat-treated screw, since soft steel spreads or mushrooms on a stubborn stud.
Best Tie Rod End Puller Picks: Five Tools Reviewed
These five tools cover outer ends, pitman arms and inner tie rods. Jaw openings and adapter sizes vary, so measure the stud area on your vehicle and compare it with the listing before you order.
1. Performance Tool W80557: Tie Rod End and Pitman Arm Puller with 3/8 in Drive Screw

- 1-1/8 in (29 mm) jaw opening
- 2-1/8 in (54 mm) pull travel
- 3/8 in drive square port in the center screw
- Forged alloy steel yoke and heat-treated screw
The Performance Tool W80557 is a classic yoke-style puller for outer tie rod ends and pitman arm joints on cars and light trucks. The maker lists a 1-1/8 inch (29 mm) jaw opening and 2-1/8 inch (54 mm) of pull travel, which covers the stud area on many passenger cars, crossovers and half-ton pickups. Measure the gap around your knuckle before ordering, since heavier trucks can need a wider jaw.
The yoke is forged alloy steel, and the center screw is heat treated so the tip holds its shape when it bears on a seized stud. A 3/8 inch drive square port in the end of the screw lets you turn it with a ratchet as well as a wrench. That helps when a brake rotor, a fender liner or a sway bar sits close and there is no room to swing a long handle.
Because the screw pushes the stud out with steady force, the boot and threads usually come through intact, so this suits jobs where you are only separating the joint to reach a strut, knuckle or axle. It is a single-size tool, so it will not cover every heavy duty truck or large drag link joint. Owners of larger rigs may want a kit with several jaw sizes instead.
View Performance Tool W80557 on Amazon
2. OEMTOOLS 27175: Damage Free Tie Rod End Remover with Swivel Pressure Tip

- Wedge-style body sits between spindle arm and tie rod
- Swivel pressure tip protects the stud
- Designed not to damage dust boots
- Suits rack and pinion and front wheel drive cars
The OEMTOOLS 27175 takes a different approach from a jaw puller. Instead of hooking under the knuckle, its body slips between the spindle arm and the tie rod end, and tightening the center fastener spreads the two apart until the taper releases. The listing aims it at rack and pinion steering, including import and front wheel drive vehicles where the space under the knuckle is tight.
The pressure tip swivels, so it stays square on the end of the stud as the tool loads up rather than skidding off and chewing the threads. The center tip also helps you line the tool up with the stud before any force goes on. The maker says it will not damage tie rod end dust boots, which makes it a sensible choice when the joint is staying on the car.
This tool depends on having a gap between the steering arm and the tie rod body, so check that space on your vehicle first. On some trucks and older cars with large linkage joints, there is not enough room or the joint is too big for it. For those, a traditional jaw puller or a pickle fork is the better match, and this remover stays in the drawer for compact cars.

3. OMT 5-Piece Front End Service Kit: Tie Rod End, Ball Joint and Pitman Arm Pullers in ABS Case

- Ball joint separator and tie rod and ball joint remover
- Conical pitman arm puller and two pitman arm pullers
- Hardened alloy construction
- Custom-molded ABS carrying case
The Orion Motor Tech front end kit bundles five separating tools in one molded case. The listing names a ball joint separator, a tie rod and ball joint remover, a conical pitman arm puller, a pitman arm and tie rod end puller, and a standard pitman arm puller. Having several jaw sizes and shapes on hand means you can switch tools when one does not fit around a particular knuckle or linkage joint.
The tools are made from hardened alloy, and each one works with ordinary sockets and wrenches on its forcing screw. The ball joint separators handle joints that sit in a tapered knuckle bore, while the pitman arm pullers grip the arm on trucks and older vehicles that use a steering box. That range makes the kit useful on a family car one weekend and a pickup the next.
Owners with only one car and a single outer tie rod end to replace may find a lone jaw puller simpler and easier to store. This set suits a DIYer who handles a whole front end, works on several vehicles or wants a backup when one tool will not reach. Note that it separates joints only; pressing a ball joint out of a control arm needs a press kit.
View OMT 5-Piece Front End Kit on Amazon
4. OTC 6299 Separator Set: 5 Pickle Forks for Tie Rods, Ball Joints and Shock Linkage

- Five pickle forks, OTC 6531 to 6535
- Fork spreads from 11/16 in to 1-5/8 in
- Removes tie rods, ball joints and shock linkage
- Blow-molded storage case
The OTC 6299 is a set of five pickle forks in a blow-molded case, sold under OTC numbers 6531 through 6535. OTC lists fork spreads from 11/16 inch to 1-5/8 inch and lengths from 11 inches to 16 inches, so you can choose a narrow fork for a small car tie rod end or a wider, longer one for a truck joint. The set is aimed at tie rods, ball joints and shock linkage on cars and light trucks.
A pickle fork is the simplest separator there is. You drive the wedge between the knuckle and the joint with a hammer, and the taper releases as the fork spreads them apart. On a joint that has been rusting in road salt for years, that sharp, direct force can work faster than a screw puller, and the longer forks keep your hands farther from the hammer blows.
The tradeoff is damage. The fork nearly always tears the rubber dust boot and can mark the knuckle, so use it only on parts you are replacing. Wear eye protection, keep the castle nut on a few turns, and support the car on stands. If you want to reuse the joint, reach for a jaw puller instead.
View OTC 6299 Pickle Fork Set on Amazon

5. Lisle 58100: 12-Piece Inner Tie Rod Tool Set with Crowfoot Adapters

- 12 crowfoot adapters, 1-3/16 in to 42 mm
- Long socket slips over the tie rod end
- Reaches inner tie rods with hidden wrench flats
- Fits many cars, trucks and SUVs
The Lisle 58100 is not a puller in the usual sense. It removes and installs inner tie rods, the joints that thread onto each end of a rack and pinion steering rack. Those joints hide under a rubber bellows, and their wrench flats are often too close to the rack or the frame for an ordinary wrench, which is where this tool earns its place.
The set pairs a long socket tube with 12 crowfoot adapters. The listing gives adapter sizes of 1-3/16, 1-1/4, 1-5/16, 1-3/8, 1-7/16 and 1-1/2 inches, plus 29, 32.5, 33.6, 38.4, 40 and 42 mm. You slide the tube over the tie rod, the crowfoot engages the joint housing, and a ratchet or breaker bar on the far end turns it off or on.
This set suits a full tie rod replacement, where the inner joint is loose as well as the outer end. Remove the outer end first with a puller, then cut or slide back the bellows clamp to reach the inner joint. It does nothing for an outer tapered stud, so most owners pair it with one of the pullers above. Check the adapter size you need against your new inner tie rod.
Which Tool for Which Steering Job
Use this table to match the job in front of you with the tool type that suits it.
| Job | Tool to reach for | Example | Keep in mind |
|---|---|---|---|
| Outer end, reusing the part | Screw-type jaw puller | Performance Tool W80557 | Check jaw opening and travel |
| Outer end on a rack and pinion car | Screw-driven wedge | OEMTOOLS 27175 | Needs a gap between arm and tie rod |
| Outer end headed for scrap | Pickle fork | OTC 6299 | Tears the boot; wear eye protection |
| Tie rods, ball joints and pitman arms | Front end kit | OMT 5-piece set | More pieces to keep track of |
| Inner tie rod at the rack | Crowfoot inner tie rod tool | Lisle 58100 | Match the adapter to the joint |
OTC describes its 6299 separator set as five popular pickle forks for removing shock linkage, tie rods and ball joints, with fork spreads from 11/16 inch up to 1-5/8 inch. That spread of sizes is the point of a set: a fork that is too wide slips out, and one that is too narrow will not start between the parts.

If a ball joint has to come out of a control arm rather than just apart from the knuckle, that is a press job, covered in our ball joint press kit guide.
Seized Tapers, Road Salt and Safe Technique
A few Michigan winters of brine can bond a tapered stud to the knuckle so firmly that the puller screw feels like it is pushing on solid metal. Soak the joint with penetrating oil the night before, then tighten the puller until it is under firm tension and give the side of the knuckle boss a sharp rap with a hammer, which often pops the taper loose.
- Support the car properly: use jack stands on solid points, never just the jack.
- Leave the nut on: thread the castle nut back a few turns so the joint cannot spring free.
- Protect your eyes: rust scale and broken cotter pins fly when the taper lets go.
- Skip the torch near rubber: heat ruins boots and rack bellows and can start a fire.
- Count the turns: note how many turns the old outer end comes off the rod so toe stays close.

Never hammer the threaded end of the stud to drive it out, because the mushroomed threads ruin a part you meant to keep. Our guide to jack stands for a home garage covers load ratings if you need a pair, and the best tie rod end puller is no help if the car is not supported safely.
After the New Tie Rod Goes In
Replacing any tie rod changes toe, even when you count threads carefully, so plan for a wheel alignment as soon as the job is done. Bad toe wears tire edges fast. Torque the new castle nut to the figure in the part instructions and fit a fresh cotter pin.
If you are shopping for the parts themselves, our roundup of replacement tie rod ends covers greaseable and sealed designs. A worn tie rod is also a good reason to look at the rest of the front end, and our guide to shocks and struts for daily drivers explains what tired dampers do to handling and tire wear.

Even with the best tie rod end puller in the toolbox, some jobs are better handed off: a taper that will not break, a seized inner tie rod or an alignment you cannot do at home. Our suspension and steering repair in Grand Rapids covers tie rods, ball joints and the checks that go with them. Hendrick Hoffman’s steering and suspension work is backed by ASE and State of Michigan certification, and his background is on our about us page.
More Buying Guides
Frequently Asked Questions
Is a pickle fork or a puller better for tie rod ends?
It depends on the part. A screw-type puller separates the joint without tearing the boot, so use it when you want to reuse the tie rod end. A pickle fork is faster on a rusted joint but usually damages the boot, so it suits a part you are replacing anyway.
Can I remove a tie rod end without a special tool?
Sometimes. A sharp hammer blow to the side of the knuckle eye can shock the taper loose, but it takes a good aim and can miss and damage nearby parts. A puller is cheap, controlled and much easier on seized joints.
Do I need a different tool for inner tie rods?
Yes. An inner tie rod threads onto the steering rack instead of sitting in a taper, so a puller does nothing for it. An inner tie rod tool uses a long tube that slides over the rod and a crowfoot adapter that grips the joint housing.
Does a new tie rod end mean the car needs an alignment?
Yes. The tie rod sets toe, and even a careful thread count only gets it close. An alignment afterward keeps the steering wheel centered and stops the tires from wearing on their edges.
Got a tie rod that will not let go, or a front end that wanders after the swap? Call 456 AutoFix at 616-279-3832, Monday to Friday from 8am to 5pm, or set up a steering check through our contact page.
Short on daytime hours? Leave the car at our shop, 456 Carrier St NE in Grand Rapids, with our after-hours drop-off and we will take it from there.
