As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A BMW that shimmies through the steering wheel under braking, knocks over expansion joints or pulls toward the curb usually has a worn arm or bushing up front. The best BMW control arms keep the factory geometry, use a solid ball joint and come from a maker that builds parts for your exact chassis.
This guide sits under our wider look at control arm brands for every type of car and narrows the field to BMW. You will find how the front axle is laid out, how to match a part to your car and six specific listings for the E46, E90, F30 and X5.
Quick answer
Which control arms should you put on a BMW?
Start with Lemforder, the original supplier on many BMWs, or a febi bilstein or TRW arm built to the same OE number. E46 owners often choose a complete front kit from URO Parts or Meyle. Whatever you buy, match chassis, drivetrain, side and position, and book an alignment afterward.
Our Quick Picks
Three quick picks: the factory-supplier arm for the E90, a full front kit for the E46 and a complete arm for the X5. All six listings are reviewed below.

Lemforder 30332 01
The factory-supplier brand, built for the E90 front axle.

URO Parts E468PCKIT
One order that covers the common E46 front wear parts.

MOOG RK620798
A complete arm assembly for BMW's larger SUVs.
How a BMW Front Axle Uses Its Arms
Most BMW sedans and coupes from the E46 onward carry two lower arms on each front corner rather than one. One arm runs sideways from the subframe to the steering knuckle and holds the ball joint. The second, often called a thrust arm or tension strut, angles forward or back and takes the braking and acceleration loads through a large rubber bushing.
That layout gives precise steering but more parts to wear. A tired thrust arm bushing often causes a shimmy at highway speed or under braking, while a loose ball joint tends to clunk over bumps.
- Arm material: many BMW arms are aluminum, which cannot be straightened after a hard hit. Replace like with like.
- Bushings: some arms arrive with bushings pressed in, others need a separate one.
- Ball joint: on most BMW lower arms the joint is part of the arm, so a worn joint means a new arm.
- Hardware: many BMW suspension bolts are single use, so have fresh ones on hand.
Matching an Arm to Your Chassis and Drivetrain
BMW uses chassis codes such as E46, E90, F30 and E70 for each generation, and the arms change between them. Within one generation they can change again for xDrive all-wheel drive, the M models and some engines. That is why each of the best BMW control arms below is shown with one application only. Never assume one part fits every version.
Before you order, enter your year, model, engine, trim and drivetrain in the Amazon fit checker, then confirm front or rear, upper or lower, and driver or passenger side. The OE number cast or printed on the old arm, usually starting with 31 12 on a BMW front arm, is the most reliable way to cross-check a listing.
The Best BMW Control Arms by Chassis
Each pick is a specific listing on Amazon US for a named BMW chassis, from a maker that supplies original equipment or builds to OE dimensions. Use the brand’s other listings to find the matching arm for your own car and side.
1. Lemforder 30332 01: Front Left Control Arm for BMW 3 Series E90

- Front left arm, front axle
- Listed for BMW 3 Series E90, 2004-2012
- German OE quality construction
- Several BMW OE numbers listed for cross-checking
Lemforder is part of ZF and supplies suspension parts to car makers as original equipment, which is why its name turns up on so many arms that come off a BMW. The 30332 01 is a single front left arm for the front axle, and its listing names the E90 3 Series from 2004 to 2012 along with other vehicles that share the part.
The listing says the arm is made to German original-equipment quality and is designed for accurate wheel guidance, with vibration damping that improves comfort. It prints a long list of BMW OE numbers, including 31 12 6 763 703 and 31 12 2 405 861, so you can compare the number on your old arm with the new one before you start. That cross-check matters on a car family with several closely related arms.
This part does one corner only, so order the matching right side arm if you plan to do both. E90-based cars came in sedan, wagon, coupe and convertible form, with rear-wheel drive or xDrive, and the arms are not all the same. Use the Amazon Confirmed Fit option with your year, model, engine and drivetrain to make sure this is the correct position for your car.
View Lemforder 30332 01 on Amazon
2. Meyle Aluminum Control Arm Kit: Front Arms for BMW E46 1999-2005

- Aluminum front control arm kit
- Listed for E46 328i, 323i, 328Ci and 330i
- Model years 1999-2005 named in the listing
- From the maker of the MEYLE HD line
Meyle is a German parts maker that sells both standard replacement parts and its MEYLE HD line, which the company describes on its MEYLE HD product page as parts reworked where the original design reaches its limits. This listing is an aluminum control arm kit for the E46 3 Series, and its title names the 1999 to 2005 328i, 323i, 328Ci and 330i.
The E46 is one of the most common BMWs still on the road, and many have now covered enough miles to need a front-end refresh. Buying the arms as a kit means both sides are replaced at once, so the car sits and steers evenly instead of pairing a new arm with an old one. Aluminum matches what BMW fitted to these cars, which keeps the unsprung weight close to stock.
The listing gives little detail beyond the title, so open the product page and check exactly which pieces are included, whether it is an HD part and which bushings or hardware you still need. Confirm that your car is rear-wheel drive, since the xi all-wheel-drive models use different arms, and run your year, model and engine through the Amazon fit checker before you order.
View Meyle E46 Aluminum Kit on Amazon

3. febi bilstein Track Control Arm: Front Left Aluminum Arm for BMW F30 and F20

- Front axle, left side
- Aluminum arm, M14 x 1.5 thread
- Listed for F20, F21, F22, F30, F31, F32 and related
- BMW OE 31 12 6 855 741 for comparison
febi bilstein is a German parts brand with a large catalog for European cars, and this track control arm covers one of the widest BMW families on the list. The listing names the front left position and a long run of chassis: the F20 and F21 1 Series, F22 2 Series, F30, F31 and F34 3 Series, and the F32, F33 and F36 4 Series, including facelift versions.
The arm is aluminum, weighs 1.6 kg according to the listing, and uses an M14 x 1.5 thread with a 12 mm inner diameter. The listing gives BMW OE number 31 12 6 855 741 for comparison and names TRW JTC1623 as a cross-reference, which makes it easy to match against the part on your car or a parts catalog. Aluminum keeps the corner light, but it should be replaced rather than straightened after any impact.
F-series cars came with rear-wheel drive or xDrive and with several engines, and the listing itself warns that all restrictions must be observed. Check the vehicle identification on Amazon with your year, model, engine and drivetrain before ordering, and buy the right side arm separately if both corners are worn. A front-end alignment is needed once the new arm is in place.
View febi bilstein 31126855741 on Amazon
4. URO Parts E468PCKIT: 8-Piece Front Suspension Kit for BMW E46

- 8-piece front suspension kit
- Alloy control arms built to factory geometry
- OE-durometer bushings where applicable
- Heat and ozone-resistant ball joint boots
URO Parts sells replacement parts for European cars, and the E468PCKIT is an 8-piece front suspension kit whose part number points to the E46 3 Series. Kits like this are popular with E46 owners because the front end tends to wear as a set: the lower arms, their bushings, tie rods and sway bar links often reach the end of their life around the same time.
The listing says the components match factory geometry for correct wheel alignment and tire wear, and that the control arms are made from high-strength alloy. It also lists OE-durometer rubber bushings, where fitted, for an original ride, plus heat and ozone-resistant boots that help keep dust and water out of the ball joints. The aim is to remove clunks and vague handling and restore stability under braking.
Because the listing does not spell out every piece in the box, read the product details to confirm what the eight parts are before you plan the job. E46 suspension differs between rear-wheel-drive and xi models, so confirm your year, model, engine and drivetrain with the Amazon fit checker. Expect to need a full alignment after a front-end rebuild of this size.
View URO Parts E468PCKIT on Amazon

5. MOOG RK620798: Control Arm and Ball Joint Assembly for BMW X5 and X6

- Control arm with ball joint fitted
- Listed for 2007-2018 BMW X5
- Also lists 2008-2019 BMW X6
- Built to support factory alignment geometry
MOOG, a DRiV brand, makes a large range of steering and suspension parts, and its RK line includes several arms for BMW’s SUVs. The RK620798 is a control arm and ball joint assembly, and its listing names the 2007 to 2018 BMW X5 and the 2008 to 2019 BMW X6. The X5 is a heavy vehicle, and its front arms carry a lot of load every time it brakes or hits a pothole.
The listing describes the arm as a key suspension component that helps keep the wheel alignment correct and the vehicle stable, and says it is built to handle everyday road stress. Having the ball joint already installed saves a separate press job and means the joint and arm are new together. MOOG lists other arms for the same vehicles, such as the RK620799, so compare the options side by side.
The listing title does not state the exact position or side, so open the product details and compare the description and part number with the arm on your vehicle. X5 and X6 front suspension differs by generation, engine and options, so confirm your year, model, engine and trim with the Amazon fit checker before buying. Plan on an alignment after fitting.
6. TRW JTC1211: Aluminum Suspension Control Arm for BMW 3 Series E90 and 1 Series

- Aluminum control arm
- Listed for 2007-2013 328i and 2007-2014 335i
- Also lists 128i, 135i and xDrive models
- Endurance tested to 500,000 cycles
TRW is a ZF brand, like Lemforder, and builds steering and suspension parts to original-equipment designs. The JTC1211 is an aluminum control arm whose listing names a long list of E90-era cars, including the 2007 to 2013 328i, the 2007 to 2014 335i, the 2006 325i and 330i, the 335d and 335is, and the 2008 to 2013 128i and 135i.
According to the listing, every TRW part passes four levels of testing and technical review before approval, including endurance testing of 500,000 cycles. The arm is aluminum to keep the suspension light, which suits the way these cars are designed to steer. The fit list includes several xDrive and xi models as well as rear-wheel-drive versions, so the part number is worth checking closely.
The listing title does not name the side or exact position, and the E90 family uses more than one arm on each front corner. Use the Amazon Check Fit option with your year, model, engine and drivetrain, and compare the result with the arm on your car before ordering. If the other side is equally worn, buy the matching arm for that corner too.
Side-by-Side: Which Listing Suits Your Car
Use the table to narrow the field, then check the part number against your own car.
| Listing | Chassis named | What you get | Suits |
|---|---|---|---|
| Lemforder 30332 01 | E90 3 Series, 2004-2012 | Single front left arm, OE supplier | Owners who want the factory brand |
| Meyle aluminum kit | E46 328i, 323i, 328Ci, 330i | Aluminum front arm kit | E46 front refresh |
| febi bilstein front left | F20, F22, F30, F32 and related | Single aluminum arm | Later 1, 2, 3 and 4 Series |
| URO Parts E468PCKIT | E46 (per part number) | 8-piece front kit | One-job front-end rebuild |
| MOOG RK620798 | X5 2007-2018, X6 2008-2019 | Arm and ball joint assembly | X5 and X6 owners |
| TRW JTC1211 | E90-family 3 Series, 128i, 135i | Single aluminum arm | Daily-driven E90, E92 and E82 cars |
When a front corner is apart anyway, it is a good moment to look at the struts. Our guide to shocks and struts for daily drivers explains when a damper is due, and doing both jobs together means one alignment instead of two.

Road Salt, Potholes and BMW Bushings
West Michigan winters wear out even the best BMW control arms sooner. Salt spray dries out bushings and creeps into any split boot, and freeze-thaw potholes hit the front arms hard. A BMW that rode well in October can knock by March.
Rinsing the underside through the winter helps, and so does a look at the boots at tire changeover. After a hard pothole hit, check for a pull or a crooked steering wheel. Our list of signs of pothole damage walks through what to look for.

Other German cars with multi-link front ends show similar patterns. Our article on Audi control arm failure symptoms describes noises that often apply to a BMW too.
Doing the Job Yourself or Booking It In
Swapping a lower arm on an E46 or E90 is within reach for a confident home mechanic with a jack, stands and a ball joint separator. On salt-belt cars, though, subframe bolts can seize into their sleeves, and rubber-bushed bolts are typically tightened with the car at ride height so the bushing is not twisted. Check your repair manual for the torque figures and sequence.
Fitting the best BMW control arms still changes camber and toe slightly, so plan on a wheel alignment afterward. If a ball joint is already loose, do not put the repair off: our guide to bad ball joint symptoms explains why.

Prefer to hand it over? Our suspension repair service in Grand Rapids covers control arms, bushings and ball joints, and our shop looks after foreign and European vehicles as well as domestic ones. Owner Hendrick Hoffman holds ASE and State of Michigan certification in steering and suspension.
More Buying Guides
Frequently Asked Questions
Lemforder or Meyle HD: which is better for a BMW?
Lemforder builds to the original BMW design and is the factory supplier on many models. Meyle says its HD line is reworked where the original parts tend to fail. Both are reasonable choices, so pick the one listed for your exact chassis and side.
What are the best control arms for E46 cars?
For a full front refresh, a complete kit such as the URO Parts E468PCKIT or a Meyle aluminum arm kit covers both sides in one order. Confirm whether your car is rear-wheel drive or an xi model, because the all-wheel-drive cars use different arms.
Should I replace BMW control arms in pairs?
It is common practice. Both sides have the same age and mileage, and matching arms and bushings help the car track straight and brake evenly.
Are aftermarket control arms safe on a BMW?
Arms from established makers that build to the OE number are a normal repair. Be wary of unbranded kits with no part numbers, and always fit new hardware and get an alignment.
Is your BMW knocking or shimmying on Grand Rapids roads? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a front-end check through our contact page.
Can’t get here during the workday? Our after-hours drop-off has you covered. You’ll find us at 456 Carrier St NE in Creston.
