456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Denso vs AC Delco: Which Iridium Plug Fits Your Engine?

denso vs ac delco: mechanic working at a cluttered workbench

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

Stand in front of the spark plug rack at any parts counter and the Denso vs AC Delco choice shows up fast. Both brands sell iridium plugs that look almost identical in the package, both supply carmakers straight from the factory, and both have loyal fans on every forum. The useful question is not which logo wins, but which plug your engine was designed around.

This guide explains where each brand comes from, then compares three current iridium plugs: the Denso Iridium TT 4702 (IK20TT), its Iridium Power sibling the Denso 5304 (IK20), and the ACDelco GM Original Equipment 41-162. If you are still deciding whether your plugs are due at all, start with our guide on how often to change spark plugs and the signs they are worn.

Quick answer

Should you put Denso or ACDelco plugs in your engine?

Use the brand and part number your engine maker specifies. ACDelco 41-series iridium plugs are GM’s original equipment line for Chevrolet, Buick, GMC and Cadillac engines. Denso supplies many Japanese engines, and its Iridium TT pairs a 0.4mm iridium tip with a platinum ground. Both are quality plugs when the part number matches.

Our Quick Picks

Two Denso iridium plugs that share the IK20 heat code and one ACDelco original equipment plug, each sold through the maker's own Amazon listing. All three are reviewed in full below.

Denso Iridium TT 4702 product photo
Denso pick

Denso Iridium TT 4702

Iridium TT, IK20TT, single plug

Twin-tip iridium and platinum plug that crosses over to many engines.

SuitsEngines where Denso's catalog lists the 4702
View on Amazon →
ACDelco 41-162 product photo
ACDelco pick

ACDelco 41-162

GM OE iridium, 41-162, single plug

The factory part for the GM engines that call for this number.

SuitsChevrolet, Buick, GMC and Cadillac engines that list 41-162
View on Amazon →
Denso Iridium Power 5304 product photo
Denso alternative

Denso Iridium Power 5304

Iridium Power, IK20, single plug

Same IK20 heat code, with a grooved ground strap in place of a needle.

SuitsEngines where Denso's catalog lists the 5304
View on Amazon →

Two Plug Makers With Factory Roots

ACDelco is the parts brand of General Motors. Its GM Original Equipment plugs are the ones GM engineers design and validate for their own engines, and the listing notes that some of them were once sold under the GM Genuine Parts or ACDelco Professional names. If you drive a Silverado, an Equinox or an older Buick, the plug that came out of your engine very likely had an ACDelco number on it.

Denso is a large Japanese supplier that makes everything from A/C compressors to ignition coils. Its plugs are factory fit in many Toyota and other Japanese engines, and Denso says its Twin-Tip design first appeared on original equipment plugs for luxury and performance cars. In the aftermarket, Denso sells several families, from Iridium Long Life to Iridium Power and the Iridium TT.

So each brand is the home team for a different set of engines. That fact matters more than any spec sheet, because a plug’s reach, seat, heat range and gap are all chosen for one combustion chamber. A well-made plug in the wrong application can still misfire.

Denso vs AC Delco: Plug Specs Side by Side

The figures below come from the three Amazon US listings and Denso’s own product page. Where a maker states nothing, the table says so rather than guessing.

PointDenso Iridium TT 4702 (IK20TT)ACDelco 41-162 (19417055)Denso Iridium Power 5304 (IK20)
Center electrode0.4mm iridiumIridium, size not listed0.4mm iridium
Ground electrode0.7mm platinum needleNot described in the listingU-groove, taper cut
Preset gap.039 in (1.0mm) on Denso’s multi-pack listingNot listed; use GM’s specNot listed; measure before fitting
SealNot described in the listingThree-piece fired-in suppressor sealNot described in the listing
Fitment basisCross-references a long list of OE numbersExact replacement for GM engines that use itShares much of the 4702’s OE list
Life claimDenso: alloy resists wear for over 100,000 milesWear resistance stated, no mileageNo mileage given
Denso vs AC Delco iridium plugs compared on the Amazon US listings and Denso’s Iridium TT page

The headline difference is philosophy. Denso built the Iridium TT as a wide-coverage upgrade plug that crosses over to many engines, while the ACDelco 41-162 is a direct factory replacement for the specific GM engines that call for that number.

Denso vs AC Delco Spark Plugs: The Three Plugs in Detail

We chose two Denso iridium plugs from different families and one ACDelco factory plug. Spark plugs are engine-specific, so treat these listings as examples of each line and confirm the exact part number with Amazon’s fit checker or the maker’s catalog before you order.

Denso 4702 IK20TT Iridium TT: Twin-Tip Spark Plug with 0.4mm Iridium Center

Denso Iridium TT 4702 product photo
Key features
  • 0.4mm iridium center electrode
  • 0.7mm platinum needle ground electrode
  • Twin-Tip design for a less obstructed spark
  • Cross-references a long list of OE numbers

The 4702, also coded IK20TT, is one of the most widely listed plugs in Denso’s Iridium TT family. It is sold here as a single plug, so a four-cylinder engine needs four and a V6 needs six. The listing shows a long string of original equipment numbers it replaces, which tells you Denso designed it as a crossover plug for many engines rather than one exact factory fit.

Its main idea is the Twin-Tip layout. A 0.4mm iridium center electrode faces a 0.7mm platinum needle ground electrode, and Denso says the two fine tips leave less metal in the way of the spark, so the flame can grow in every direction. Denso also states that its iridium alloy resists wear for over 100,000 miles, and its multi-pack listing of the same plug gives a preset gap of .039 inch, or 1.0mm.

The 4702 makes sense when Denso’s parts finder or Amazon’s fit checker lists it for your exact year, engine and trim. Check the gap against your service information before you install it, and handle the fine tip with care. It is not the answer for an engine whose maker calls for a different heat range or a specific factory plug, so do not buy it on the strength of the twin-tip design alone.

View Denso Iridium TT 4702 on Amazon

Two metal plug-shaped parts on a gray surface

ACDelco 41-162 (19417055) Iridium: GM Original Equipment Spark Plug

ACDelco 41-162 product photo
Key features
  • GM Original Equipment iridium plug
  • Exact replacement for the original part
  • Three-piece fired-in suppressor seal
  • Designed and validated by GM engineers

The 41-162 carries GM part number 19417055 and belongs to ACDelco’s GM Original Equipment range. The listing describes it as an exact replacement for the original component, and it says GM engineers design and validate these parts for Chevrolet, Buick, GMC and Cadillac vehicles. Some parts in the range were once sold as GM Genuine Parts or ACDelco Professional, so an older box with a different label can hold the same plug.

The plug uses an iridium electrode, which the listing credits with a high melting point and the strength to resist wear. ACDelco lists steady idle, reliable cold starting, quick acceleration and smooth running as the benefits. A three-piece fired-in suppressor seal meters spark energy for long electrode life, helps prevent combustion leakage and helps block radio interference that can upset the vehicle’s electronics.

The listing does not give a gap or a vehicle list, so confirm with Amazon’s fit checker or a GM parts catalog that your engine uses 41-162, then check the gap against GM’s spec. On a GM engine that calls for this number, it is the most direct way to put back what the factory installed. It does not suit non-GM engines, and its iridium design will not cure a misfire caused by a coil or injector.

View ACDelco 41-162 on Amazon

Denso 5304 IK20 Iridium Power: Spark Plug with U-Groove Ground Electrode

Denso Iridium Power 5304 product photo
Key features
  • 0.4mm iridium center electrode
  • U-groove and taper cut ground electrode
  • Patented 360 degree laser-welded center tip
  • Shares many OE cross-references with the 4702

Coded IK20, the 5304 belongs to Denso’s Iridium Power line and carries the same IK20 heat code as the twin-tip 4702 above. It also comes as a single plug, and its listing opens with many of the same original equipment numbers, including 12610767 and 1822A002, so Denso offers the pair as alternatives across much of the same engine coverage.

The split between them is on the ground side. Rather than a platinum needle, the Iridium Power uses a U-groove and taper cut ground electrode, which Denso credits with faster flame growth and less heat quenching. The center tip is the same 0.4mm iridium, joined to the electrode by a patented 360 degree laser weld that Denso says gives a strong, lasting bond.

Reach for the IK20 when Denso’s catalog lists it for your engine and you prefer a conventional ground strap over a fine platinum point. The listing gives no preset gap, so measure each plug before installing it. Like its twin-tip sibling, it is no stand-in for a GM engine that specifies the ACDelco 41-162, nor for an engine that needs another heat range.

View Denso Iridium Power 5304 on Amazon

Mechanic working under the hood of a car

Heat Range, Gap and Fit Explained

Heat range numbers do not cross brands

Heat range describes how quickly a plug sheds heat from its firing tip into the cylinder head. A plug that runs too hot can cause pre-ignition, and one that runs too cold can foul with carbon in short-trip driving. The “20” in Denso’s IK20TT is its heat code, and Denso’s own part numbering chart shows that the same heat range carries a different number at NGK, Champion and Bosch.

ACDelco’s 41-series numbers are catalog numbers rather than a readable heat scale. That means you cannot swap brands by matching digits. Use a cross-reference from the plug maker, or simply buy the number listed in your owner’s manual or parts catalog.

Chrome V8 engine in a classic car

Gap: check it, but handle fine tips gently

The gap is the space the spark jumps between the center and ground electrodes. Denso’s multi-pack listing for the 4702 gives a preset gap of .039 inch (1.0mm), and the ACDelco listing gives none, so compare each plug against the gap in your service information. If a change is needed, use a wire-style gauge and bend only the ground strap, never pry against a fine iridium tip.

Original equipment fitment

Both brands publish catalogs that list plugs by year, make, model and engine. On a GM engine, the ACDelco number is the factory part, and on many Japanese engines the factory plug wears a Denso or NGK label. Denso’s Iridium TT product page explains the twin-tip design and links to its parts finder, which is a quick way to check whether a TT plug is offered for your engine at all.

Which Plug Suits Which Engine

Use the engine under your hood as the tiebreaker, not the price tag or the forum vote.

Your situationBetter fitWhy
GM engine that shipped with ACDelco 41-162ACDelco 41-162Same part GM validated for that engine
Toyota or other engine with a Denso plug from the factoryDenso, matched by catalogKeeps the original heat range and design
Engine where Denso lists the 4702 as a replacementDenso Iridium TT 4702Twin-tip design with a 1.0mm preset gap
Engine where Denso lists the 5304 insteadDenso Iridium Power 5304Same heat code with a grooved ground strap
Any engine with a tuned or modified ignitionAsk a tuner or mechanicHeat range may need to change
Unsure which plug is installed nowPull one plug and read itThe number on the insulator tells you
Choosing between Denso and ACDelco iridium plugs by engine and situation

When both brands list a plug for your engine, either is a sound choice. Buy from the brand’s own Amazon listing rather than an unbranded bundle, and look over the box and plugs for consistent printing before installing them.

Cold Starts and Wet Roads in West Michigan

A Grand Rapids winter is hard on ignition parts. Cold, dense air and a rich cold-start mixture ask more of the spark, and a plug with a worn, rounded tip needs more voltage to fire. That extra demand lands on the ignition coils, which is why worn plugs and failing coils so often show up together in January.

Car on a snowy street in winter

Short winter trips also matter. An engine that never fully warms up leaves carbon on the insulator, and a plug that runs too cold for the engine fouls faster. Slush and road salt sprayed across the engine bay can work into worn coil boots, so check the boots for cracks and white tracking marks whenever the plugs come out.

A thin film of dielectric grease inside each boot helps keep moisture out. Whether the plug threads take anti-seize depends on the plug maker’s instructions, since many plugs have plated threads and torque specs that assume dry threads.

When a New Plug Will Not Fix It

Fresh plugs cure a misfire only when the old plugs were the cause. If the misfire stays after a plug change, the fault may sit in a coil, an injector, a vacuum leak or low compression. A blinking warning lamp is a serious sign, and our article on why a check engine light is flashing explains why you should ease off and get the car checked soon.

Mechanic's hands working on a car part

A hesitation under load that does not clear after new plugs is another clue that something else is wrong, and our guide to a car that hesitates when accelerating covers the usual suspects. Our shop handles check engine light diagnostics in Grand Rapids, reading the misfire counters and testing coils and injectors before any parts get replaced.

Frequently Asked Questions

Is Denso better than ACDelco?

Neither brand is better for every engine. ACDelco’s GM Original Equipment plugs are the factory parts for many Chevrolet, Buick, GMC and Cadillac engines, and Denso is factory fit on many Japanese engines. The better plug is the one whose part number your engine maker or the plug maker’s catalog lists.

Can I use Denso plugs in a GM engine?

Yes, if Denso’s catalog lists a plug for that exact engine. Match it through Denso’s parts finder rather than by copying digits from the old plug, because heat range numbers differ between brands. If no Denso listing exists for your engine, stay with the ACDelco part.

Do new iridium plugs need to be gapped?

Check the gap on every new plug against your engine’s spec, even when it comes preset. Denso lists a 1.0mm gap for the 4702 multi-pack. If you must adjust it, use a wire gauge and move only the ground strap so the fine iridium tip is not damaged.

Will new spark plugs turn off my check engine light?

Only if worn plugs caused the code. Misfire codes can also come from coils, injectors or vacuum leaks, and the light may need the code cleared or a few drive cycles to go out. If it returns or flashes after new plugs, have the system diagnosed.

Still chasing a misfire after a fresh set of plugs? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or schedule a check engine diagnosis online.

Can’t get away from work during the day? Leave the car with our after-hours drop-off and we’ll take it from there. We work out of 456 Carrier St NE in Creston.