As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
Lift a Tacoma a couple of inches and the factory upper arms start to run out of room: the ball joint binds, caster drops and the alignment shop can’t bring camber back into range. The best control arms for Tacoma trucks depend on which of two jobs you have, correcting geometry on a lifted truck or replacing a worn arm on a stock one.
This guide covers both, with six listings sorted by generation and position. Not sure an arm is the culprit? Our write-up on control arm failure symptoms describes the clunks, shimmies and uneven tire wear that point to tired bushings or joints on any vehicle.
Quick answer
Which control arms should a Tacoma owner buy?
For a lifted 2005-2023 Tacoma, the ICON tubular arm with Delta Joint or Old Man Emu UCA0005 restore caster and joint angle. Stock trucks can use OE-style parts such as the Dorman 522-721 upper or Mevotech GS861297 lower. Confirm year, drivetrain and side in Amazon’s fit checker first.
Our Quick Picks
Three listings that cover the main Tacoma situations: a lifted daily driver, a mild lift and a stock truck with a worn arm.

ICON Tubular Upper Control Arm
Tubular upper arm with a sealed high-angle joint and added caster.

Old Man Emu UCA0005 Upper Control Arms
Forged arms with a greasable joint and extra camber and caster.

Dorman 522-721 Upper Control Arm
OE-style upper arm with ball joint and bushings already fitted.
Lift Correction or Like-for-Like Replacement?
Owners running a coilover or spacer lift of roughly two inches or more buy aftermarket upper arms to pull the wheel back into position. Owners of stock trucks want a direct replacement when a bushing tears or a joint develops play.
A lift arm is usually tubular or forged, has a high-angle joint and changes caster on purpose. A replacement arm copies the factory dimensions, so Toyota’s alignment specs still apply.
Generation matters too. The 2005-2023 trucks share one basic front end, the first gen uses different arms, and 2024 and later trucks are another design again.
What Sets One Tacoma Arm Apart From the Next
- Joint type: uniballs articulate freely but leave the internals exposed, while sealed high-angle ball joints keep water and grit out.
- Caster and camber: lift arms build in extra caster so the truck tracks straight; check the lift height each maker names.
- Bushings: rubber rides quietly, while polyurethane feels firmer and may need grease.
- Position: OE-style arms are sold by side and by upper or lower, so read the listing’s position before you order.
ICON’s page on its sealed, greasable Delta Joint sums up the trade-off well. The company says open uniballs let road salt, dirt and mud reach the internals, so it built a high-angle joint with a zinc-plated housing.
Best Control Arms for Tacoma: Six Listings Compared
The first three listings are lift arms for second and third gen trucks, the fourth covers first gen owners and the last two are factory-style replacements. Each names its own years and position, so treat this as a shortlist and confirm your truck in Amazon’s fit checker.
1. ICON Tubular Upper Control Arm: 2005-2023 Tacoma with Delta Joint

- Listed for 2005-2023 Toyota Tacoma
- Patented ICON Delta Joint
- 1026 DOM steel, CNC bent tubing
- Built-in caster correction
This ICON listing is a tubular front upper control arm for 2005-2023 Toyota Tacoma trucks, supplied with ICON’s Delta Joint kit. It is aimed at owners whose factory upper arms no longer give enough camber or caster adjustment after a lift.
The arm is built from 1026 DOM steel with CNC bent tubing and CNC machined bushing housings and sleeves. ICON lists serviceable dual stage bushings and built-in caster correction, which pushes the front wheel forward slightly so the truck tracks straight after a lift. The Delta Joint is ICON’s sealed, greasable high-angle joint, which the company designed to give uniball-style articulation while keeping road salt and grit away from the bearing surfaces.
In practice, this is a sensible match for a lifted Tacoma that commutes through a Michigan winter and goes off-road on weekends, because a sealed joint asks for less attention than an open uniball. The listing does not state a lift height range, so check ICON’s guidance for your coilover or spacer setup before ordering. It is not a part for a stock-height truck that just needs a worn arm replaced, and it does not fit 2024 and later Tacomas, which ICON sells separately. Confirm your year and drivetrain on Amazon, then book an alignment once the arms are installed.
View ICON Tubular Upper Control Arm on Amazon
2. Old Man Emu UCA0005: Forged Upper Arms with Greasable Ball Joint

- Listed for 2005-2015 and 2015-on Tacoma
- Forged joint housing and eyelets
- Geometry corrected for 50mm of lift
- Maintenance-free GIIRO bushings
The Old Man Emu UCA0005 is an upgrade upper control arm set from ARB’s suspension brand, listed for Toyota Tacoma 2005-2015 and 2015-on trucks. The listing says the arms are boxed in pairs, with foam inserts and fitting instructions included, and that they are engineered to work with Old Man Emu GVM upgrades.
Construction centers on a forged ball joint housing and forged eyelets, with a heavy duty greasable ball joint under an Old Man Emu protective cap. The arms add camber and caster for a 50mm lift, which is roughly two inches, and include a mount provision for the factory ABS wiring. Old Man Emu fits its GIIRO bushings, which it describes as free pivoting, grease free and maintenance free, and the listing says the arms passed testing to VSB14 requirements.
These arms suit a Tacoma running a moderate lift, especially an Old Man Emu spring and shock package, where the owner wants a greasable joint rather than a uniball. The 50mm figure matters: a truck lifted much higher may need a different arm with more correction. Because the listing pairs early and later years in one title, check your exact model year and drivetrain in Amazon’s fit checker, and have the truck aligned once the arms are fitted.
View Old Man Emu UCA0005 Upper Control Arms on Amazon

3. Rough Country 74201A: Forged Upper Arms for Tacoma with 3.5 in. Lift

- Listed for 05-23 Tacoma and 10-24 4Runner
- Forged arms with POM ball joints
- Requires 3.5 inches of suspension lift
- Clevite OEM style rubber bushings
Rough Country’s 74201A is a set of forged upper control arms listed for 2005-2023 Toyota Tacoma trucks and 2010-2024 4Runners. The listing names a firm minimum: it requires 3.5 inches of suspension lift, so it is meant for trucks that have gone beyond a simple leveling kit.
The arms are forged rather than welded, which Rough Country points out removes welding weak spots. They use POM ball joints, which the company says give a greater range of motion and make installation easier, and the ball joint angle is corrected for lifted applications. Pivot bushings are Clevite brand OEM style rubber, which tends to ride more quietly than polyurethane on a truck used every day. Rough Country backs the arms with its Limited Lifetime Replacement Warranty, as stated on the listing.
This set makes most sense on a Tacoma already wearing a Rough Country lift or another kit of at least 3.5 inches, where stock arms leave the upper joint near its limit. It is the wrong choice for a lightly lifted or stock truck, since the corrected geometry assumes the extra height. Confirm your model year, cab and drivetrain through Amazon’s fit checker before buying. After installation, the truck needs an alignment.
View Rough Country 74201A Forged Upper Control Arms on Amazon
4. ICON 58400DJ: Tubular Upper Arm with Delta Joint for 1996-2004 Tacoma

- Listed for 1996-04 Tacoma and 96-02 4Runner
- Direct bolt-in design
- Patented Delta Joint
- CNC machined steel taper adapter
First gen Tacoma owners have fewer choices than owners of later trucks, and ICON’s 58400DJ is a lift-oriented upper arm with a clear listing for them. It is named for 1996-2004 Toyota Tacoma and 1996-2002 4Runner models, the trucks that share this older front suspension layout.
ICON describes it as a direct bolt-in design, so it uses the factory mounting points without cutting or welding. The arm is made from 1026 DOM steel with CNC bent and notched tubing, and it comes with ICON’s patented Delta Joint and a CNC machined steel taper adapter for the steering knuckle. ICON says the Delta Joint combines the durability and weather resistance of a ball joint with the articulation of a uniball, which helps on an older truck that may already be fighting rust.
This arm is suited to a lifted first gen truck where the stock upper arm has run out of adjustment or the joint is binding at full droop. The listing does not state a lift height range, so confirm the arm suits your spring and shock setup, then check year, drivetrain and engine in Amazon’s fit checker. It will not fit 2005 and later Tacomas. Plan on an alignment once the arm is in place.
View ICON 58400DJ Tubular Upper Control Arm on Amazon

5. Dorman 522-721: Front Driver Side Upper Arm and Ball Joint Assembly

- Front driver side upper position
- Pre-installed ball joint and bushings
- Direct replacement for the original assembly
- Added rust and corrosion coatings
Dorman’s 522-721 is a factory-style front driver side upper control arm and ball joint assembly. The Amazon listing says it fits select Toyota models, and interchange listings for 2005-2023 Tacoma upper arms name 522-721 as the matching Dorman number.
The assembly arrives with the ball joint and bushings already installed, so there is no pressing of old bushings. Dorman says it directly replaces the original assembly on specific vehicles, has gone through the company’s testing for a stable ride, and carries additional coatings for rust and corrosion resistance. That last point matters on a truck that sees salted roads several months of the year.
This is the arm to look at when a stock Tacoma has a torn upper bushing, a loose upper joint or a clunk traced to the driver side upper arm, and you want the truck to drive as it did from the factory. It does not add caster or camber for a lift, so a raised truck is better served by one of the aftermarket arms above. Because the listing covers several Toyota models, enter your Tacoma’s year, cab and drivetrain into Amazon’s garage tool before ordering. The passenger side is a separate part number, and an alignment is needed after either arm is replaced.
View Dorman 522-721 Upper Control Arm on Amazon
6. Mevotech GS861297: Front Left Lower Arm and Ball Joint for 2016-2023 Tacoma

- Front left lower position
- Listed for 2016-2023 Tacoma
- Designed to meet or exceed OE specs
- Protective surface treatment against rust
Lower arms carry most of the front weight on a Tacoma and take the brunt of potholes. Mevotech’s GS861297 is a front left lower control arm and ball joint assembly listed for 2016-2023 Toyota Tacoma trucks, which makes it a direct option for third gen owners with a worn driver side lower.
Mevotech states the part is precision engineered to meet or exceed OE specifications for fit, form and function. It uses a protective surface treatment to slow rust build up, backed by the company’s quality control process. Buying the arm with the joint already fitted avoids pressing a new joint into an old, corroded arm, and it replaces the lower bushings at the same time.
This part suits a third gen Tacoma with a torn lower bushing, a lower joint with play, or an arm bent by a hard pothole or curb strike. It is not a lift part, and it will not fit 2005-2015 trucks, which use a different lower arm. The listing is for the left side only, so order the matching right side part separately if both are worn. Confirm year, drivetrain and trim in Amazon’s fit checker, follow Toyota’s torque values for the pivot bolts and joint nut, and book an alignment after installation.
View Mevotech GS861297 Lower Control Arm on Amazon
Which Arm Goes With Which Truck
The years and positions below come from the Amazon listings, and none promise a fit on every cab, bed and drivetrain in that range.
| Your truck | Arm type | Listings to check |
|---|---|---|
| 2005-2023, lifted about 2-3 inches | Upper pair, sealed high-angle joint | ICON tubular with Delta Joint |
| 2005-2015 and 2015-on, about 50mm of lift | Upper pair, greasable joint | Old Man Emu UCA0005 |
| 2005-2023 with 3.5 inches or more of lift | Forged upper pair | Rough Country 74201A |
| 1996-2004 first gen | Tubular upper pair | ICON 58400DJ |
| Stock truck, worn driver side upper | OE-style upper with joint | Dorman 522-721 |
| Stock 2016-2023, worn driver side lower | OE-style lower with joint | Mevotech GS861297 |
If two listings look equally suitable, pick by joint style. A Tacoma on salted roads all winter gets more years from a sealed joint than from an open uniball, which is one reason the best control arms for Tacoma daily drivers tend to use one.

Winter Roads, Potholes and Lifted Front Ends
West Michigan is hard on front suspension. Brine and salt settle into bushings and joint boots from November to March, and the freeze-thaw cycle leaves potholes that slam the lower arms.
Lifted trucks feel it more because the arms work at steeper angles. Tired dampers let the front end crash into every bump, which loads arms and joints harder. Our guide to shocks and struts for everyday driving covers how to spot worn ones, and our roundup of control arm brands for cars and SUVs compares the OE-style makers in more depth.

Before ordering parts for an older truck, it is worth running the VIN through Toyota’s recall and service campaign lookup. The record also shows what a dealer has already replaced on a used Tacoma.
Doing the Swap at Home or Booking It
Upper arm swaps on a Tacoma usually mean removing or compressing the coilover, separating the upper joint taper and working around the ABS and brake lines. The coil spring stores a lot of energy, so use a rated compressor or a preassembled strut. Torque the pivot bolts with the truck at ride height so the bushings don’t preload.

Even the best control arms for Tacoma lifts need an alignment afterwards, because caster and camber change the moment the arm comes off. If you would like the job done for you, our Grand Rapids suspension repair service handles control arm replacement and the steering checks that go with it. Steering and suspension is one of the areas where Hendrick Hoffman carries both ASE and State of Michigan certification.
More Buying Guides
Frequently Asked Questions
Does a leveling kit on a Tacoma need new upper control arms?
Often not for a small spacer lift. Once the front sits roughly two inches or more above stock, many trucks run out of camber and caster adjustment, and aftermarket upper arms bring both back into range. An alignment printout shows whether you need them.
Uniball or ball joint upper arms for a daily-driven Tacoma?
For a truck that sees salted winter roads, a sealed high-angle ball joint is the lower-maintenance choice. Open uniballs articulate well off-road but let grit and moisture reach the bearing, so they need checking more often.
Will 2005-2023 Tacoma control arms fit a 2024 truck?
No. The fourth gen Tacoma uses a different front suspension, and makers list separate parts for it. Always match the arm to the model years named on the listing.
Do I need an alignment after replacing Tacoma control arms?
Yes. Any arm swap changes camber, caster and toe, and lift arms change caster on purpose. Book an alignment straight after the job to keep the truck tracking straight and the tires wearing evenly.
Tacoma wandering after a lift, or knocking over every frost heave? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or book a front end check through our contact page.
Working until close? Bring the truck to 456 Carrier St NE in Grand Rapids whenever suits you and use our after-hours drop-off for the keys.
