As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A worn control arm on a Ford F-150 rarely fails all at once. It starts as a knock over railroad tracks, then a pull to one side and a front tire that wears on its inner edge. The best control arms for F150 trucks are the ones built for your generation and position, and, if the truck has been leveled, the ones made to handle the new ball joint angle.
This guide splits the choices into stock replacement arms and lift-ready upper arms, then sorts both by model year. If you are still working out whether the arm is the source of the noise, our write-up on control arm failure symptoms walks through the warning signs, and most of them apply to trucks too.
Quick answer
Which control arms should you buy for an F-150?
For a stock-height 2004-2020 truck, an OE-style upper arm such as the MOOG RK80306 or the Detroit Axle pair is the usual fix. Newer trucks need a lower arm like the Mevotech CMS401205. Leveled trucks do better with a lift arm such as the Rough Country 51036. Confirm year, drive and trim on Amazon.
Our Quick Picks
Three listings that cover a stock older truck, a newer truck and a leveled truck. Confirm your year, drive and trim on Amazon before you order.

Detroit Axle Upper Control Arm Pair
Both upper arms for one order, listed across four F-150 generations.

Mevotech CMS401205
A Mevotech lower arm for the aluminum-body era F-150.

Rough Country 51036
Lift-style upper arms that correct ball joint angle on raised 4WD trucks.
Model Year and Position Come First
Ford has used several front suspension designs on the F-150 since 2004, and the arms change with them. Parts makers tend to group the trucks into 2004-2008, 2009-2014, 2015-2020 and 2021 onward, although some upper arms span from 2004 all the way to 2020. Lower arms are more specific, so a part for a 2011 truck will not bolt onto a 2017.
Position matters just as much. Each front corner has an upper and a lower arm, and many listings are sold as a single left or right side. The upper ball joint comes built into the arm, so a worn joint means a new arm. Raptor trucks use their own long-travel parts, and some listings name 4WD or RWD only.
Stock Height or Leveled: Two Different Shopping Lists
On a truck at factory ride height, an OE-style arm makes the most sense. It restores the original geometry, uses rubber bushings that soak up road noise, and needs no extra parts. Several of the best control arms for F150 owners at stock height follow this style.
Leveling kits and lifts change the picture. Raising the front pushes the stock upper ball joint toward the end of its travel, and alignment shops can run out of camber and caster adjustment. Aftermarket upper arms move the ball joint and give back that range, which is why they are sold for 2-4 inch lifts. DRiV’s Garage Gurus team makes a related point in a ride height and alignment tech tip, noting that ride height has a direct impact on a vehicle’s alignment.
A lift arm is not automatically the upgrade for a stock truck, though. Polyurethane bushings and stiffer joints can pass more vibration into the cab, and some designs need greasing on a schedule. If the truck has never been raised, an OE-style arm is the simpler choice.
Best Control Arms for F150: The Picks by Generation
Every listing below names the F-150 years and the position it was made for. Use that as a shortlist, then run your own truck through Amazon’s fit checker, since cab, drive and trim can change the part number.
1. MOOG RK80306: Front Left Upper Control Arm and Ball Joint for 2004-2014 F-150

- Front left (driver side) upper position
- Listed for 2004-2014 F-150 and 2006-2008 Mark LT
- Arm and ball joint in one assembly
- Also listed for 2007-2017 Expedition
The MOOG RK80306 is a complete front upper control arm for the driver side, with the ball joint and bushings already fitted. Its Amazon listing names the 2004 through 2014 F-150, the 2006-2008 Lincoln Mark LT and the 2007-2017 Expedition. On these trucks the upper ball joint is part of the arm, so a loose or torn joint means replacing the whole assembly, and this part is built for exactly that job.
MOOG, part of DRiV, describes the arm as a key piece of suspension geometry that helps hold wheel alignment and keep the truck stable. The listing points to construction meant to stand up to everyday road stress, which suits a work truck that carries loads and sees rough pavement. Because it follows the factory layout, it keeps the original ride feel and does not ask for extra parts or brackets during installation.
This is a single left side arm. The passenger side is sold separately as the RK80308, and many owners replace both while the front end is apart. It is designed for stock ride height, so a leveled truck may be better served by a lift-style arm. Enter your year, drive and trim into Amazon’s fit checker before ordering.
2. Detroit Axle Front Upper Control Arms: Left and Right Pair with Ball Joints for 2004-2020 F-150

- Driver and passenger upper arms in one set
- Listed for 2004-2020 F-150, except Raptor and 60th Anniversary
- Ball joints pre-installed
- 10-year warranty as listed
Detroit Axle sells this kit as a pair of front upper control arms, one for each side, with the ball joints already pressed in. The listing covers a wide span: 2004 through 2020 F-150 trucks, excluding the Raptor, SVT Raptor and 60th Anniversary Edition, along with the Expedition, Navigator and 2006-2008 Mark LT. Build date notes apply to the 2006 Expedition and Navigator, so read the fine print if you own one of those.
The listing shows a 10-year warranty, and Detroit Axle says the arms are tested for impact, wear and fatigue. Buying both sides together keeps the arms matched in age and bushing condition, which helps the steering feel even and saves a second trip under the truck when the other side starts to knock a few months later.
The arms follow the stock design, so they are aimed at trucks at factory height rather than lifted builds. Because the listing spans so many model years, it is especially important to confirm the fit for your truck, including drive type and trim, using Amazon’s fit checker. Plan on an alignment after installation, as with any upper arm swap.
View Detroit Axle Upper Control Arm Pair on Amazon

3. MOOG CK621267: Front Left Lower Control Arm and Ball Joint for 2009-2013 F-150

- Front left (driver side) lower position
- Listed for 2009-2013 F-150
- Also listed for 2009-2013 Expedition and Navigator
- Arm and ball joint assembly
The MOOG CK621267 is a lower control arm for the front driver side, supplied as an assembly with its ball joint. The Amazon listing names the 2009 through 2013 F-150, plus the Expedition and Lincoln Navigator from the same years. Lower arms on these trucks carry the spring and much of the vehicle weight, so worn bushings here often show up as a clunk under braking or a vague, wandering feel on the highway.
MOOG says its control arms are designed to help maintain proper wheel alignment and stable handling, and to resist the stress of daily driving. As a complete arm, it replaces the bushings and the joint in one go, which is often quicker than pressing out a seized bushing that has spent years soaking in road salt.
This listing is narrower than the upper arm options above. It is a single left side part for one five-year window, and lower arms on these trucks can differ by drive type, so it is not a part to guess on. Check your truck in Amazon’s fit checker and order the matching right side arm if both are worn.
4. Mevotech CMS401205: Front Left Lower Control Arm and Ball Joint for 2015-2024 F-150

- Front left (driver side) lower position
- Listed for 2015-2024 F-150
- Stamped steel with corrosion-resistant finish
- Greasable, with 90 degree SAE fitting included
Mevotech’s CMS401205 is a front lower control arm and ball joint assembly for the driver side. The listing title names the 2015 through 2024 F-150, which covers the aluminum-body generation and the redesign that followed. Few of the classic replacement arms reach these newer trucks, so this is a useful option for owners whose lower arm bushings have started to tear or whose ball joint has developed play.
According to the listing, the arm uses stamped steel built to meet or exceed OE specifications, patented sintered bearings in the joint, and a protective surface treatment against rust. It also comes with a part-specific nylon locking nut and a 90 degree SAE grease fitting, so the joint can take fresh grease. That matters on a truck driven through Michigan winters, because new grease helps push out water and grit.
It is a single left side arm, so order the right side separately if both are worn. Some trims and drive types use different lower arms in this range, so the year span alone is not a guarantee of fit. Confirm your exact truck with Amazon’s fit checker first.
View Mevotech CMS401205 on Amazon

5. Rough Country 51036: Forged Aluminum Upper Control Arms for 2009-2020 F-150 4WD Lifts

- Forged solid aluminum arms, no welds
- POM ball joints that correct lifted ball joint angle
- Clevite OEM-style rubber bushings
- Listed for 2009-2020 F-150 4WD
Rough Country’s 51036 kit is a pair of front upper control arms made for raised trucks. The listing names the 2009 through 2020 F-150 with four-wheel drive. Instead of copying the factory arm, it relocates the ball joint to correct the steep angle that a leveling kit or lift creates, which gives the alignment more room to bring camber and caster back into range.
The arms are forged from solid aluminum, so there are no welded seams, and they use POM ball joints that the maker says offer a greater range of motion and easier installation. Rough Country chose Clevite OEM-style rubber bushings rather than polyurethane, which tends to keep the ride closer to stock, and the arms are listed as fully greaseable. The listing also mentions a limited lifetime replacement warranty from Rough Country.
This kit is aimed at trucks that have already been raised, not at a stock F-150 with a worn arm. It is listed for 4WD trucks only, so 2WD owners should look elsewhere. Check Amazon’s fit checker with your year and drive type, and book an alignment once the arms are on.
View Rough Country 51036 on Amazon
6. KSP 2021+ F150 Upper Control Arms: Adjustable Pair for 2-4 Inch Lifts

- Listed for 2021-2026 F-150, not Raptor
- Made for 2-4 inch front lift
- DOM tube arms with powder coat finish
- Greasable ball joint and PU bushings
KSP’s upper control arms for the 2021 and newer F-150 are sold as a pair for trucks with a 2 to 4 inch front lift. The listing names the 2021 through 2026 F-150 and says they do not fit the Raptor. Most lift arms on the market were designed around the older 2004-2020 trucks, so a set built for the current generation fills a real gap for owners who leveled a newer truck.
The arms are made from DOM steel tube with a powder coated finish, and the ball pin is heat treated alloy steel with a hex hole that helps during installation. A dust boot comes fitted, the socket is greasable, and the bushings are polyurethane, which the listing says handles hot and cold weather. KSP’s notes ask owners not to over-tighten the copper grease fitting and say the new joint does not need extra grease within the first year.
Polyurethane bushings usually pass more road feel into the cab than rubber ones, so expect a firmer ride than stock. These arms are meant for lifted trucks, not stock height replacements. Recheck your year and trim on Amazon before buying, and plan an alignment afterward.
View KSP 2021+ Upper Control Arms on Amazon
F-150 Fit Chart for These Arms
This chart narrows the best control arms for F150 trucks down to the year each listing names. Treat it as a starting point and check your VIN before you order.
| F-150 years (as listed) | Position | Ride height | Listing to check |
|---|---|---|---|
| 2004-2014 | Front left upper | Stock | MOOG RK80306 |
| 2004-2020, not Raptor | Front upper pair | Stock | Detroit Axle upper pair |
| 2009-2013 | Front left lower | Stock | MOOG CK621267 |
| 2015-2024 | Front left lower | Stock | Mevotech CMS401205 |
| 2009-2020 4WD | Front upper pair | Leveled or lifted | Rough Country 51036 |
| 2021-2026, not Raptor | Front upper pair | 2-4 inch lift | KSP 2021+ arms |
Our overview of control arm brands and what sets them apart explains how MOOG, Mevotech, Dorman and others build their lines.

Salt, Potholes and Tired Bushings
Grand Rapids winters work against every F-150 front end. Brine and road salt creep into split ball joint boots and cracked bushings, and freeze-thaw potholes hammer the arms each spring.
Look at the boots every time the truck is up for an oil change. If an arm has a grease fitting, a few pumps in the fall pushes out the water that collects over summer. Bushings that have cracked or shifted in their sleeves are a sign the whole arm is near the end, even if the ball joint still feels tight.

Not every clunk is an arm, so check the rest of the corner as well. Leaking or soft shocks let the suspension bang into its stops, and our list of shocks and struts for daily drivers covers what to look for there.
Installing the Arms or Handing Off the Job
Swapping an upper arm on an F-150 is a bolt-on job for a confident home mechanic, but the truck has to be supported on stands, the coil-over or spring must stay under control, and every fastener needs the factory torque. Bushing bolts are normally tightened with the suspension at ride height, not hanging, or the new rubber twists and wears early.

Picking the best control arms for F150 trucks is only part of the work, because any new arm moves the alignment. Book an alignment once the parts are in. If you would rather not tackle it, our suspension repair service in Grand Rapids can inspect the front end, replace the arms and set the alignment. Hendrick Hoffman, who owns the shop and leads the work, holds ASE and State of Michigan certification in steering and suspension.
More Buying Guides
Frequently Asked Questions
Do I need new upper control arms after leveling my F-150?
Not always. Many trucks run a small level on stock arms. As the lift grows toward 2 inches and beyond, the upper ball joint angle gets steep and alignment adjustment runs short, which is when lift-style upper arms help.
Can I replace just the ball joint instead of the upper arm?
On most 2004 and later F-150s the upper ball joint is part of the arm, so the arm is replaced as one unit. Lower joints vary by year and drive type, so check your truck before you shop.
Should I replace both sides at once?
It is usually worth it. Both arms have covered the same miles and seen the same salt, and a matched pair keeps the steering feeling even from side to side.
Is an alignment needed after new control arms?
Yes. New arms and bushings shift camber and caster, so an alignment keeps the truck tracking straight and protects the tires.
Truck clunking over every expansion joint or chewing through front tires? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a front end inspection through our contact page.
If your workday keeps you busy until we close, bring the F-150 to 456 Carrier St NE, Grand Rapids, MI 49505 and use the after-hours drop-off.
