As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A Wrangler that keeps bouncing after every expansion joint, or a Grand Cherokee whose nose dives hard under braking, is telling you the dampers are finished. Picking the best shocks for Jeep models starts with two questions: which Jeep you drive, and how far it sits above factory height.
This guide covers the Wrangler JK and JL, the Grand Cherokee and the Cherokee. It explains why a solid axle Wrangler and a strut-front SUV need very different parts, how lift height changes the shock you order, and six specific Amazon listings, each tied to a named model and position.
Quick answer
Which shocks should a Jeep owner buy?
Match the shock to your model and lift. A lifted JL suits a Bilstein 5100 set sized for its lift, a stock JK suits the Rancho RS5000X set, and a sagging Grand Cherokee front is easiest to fix with a loaded strut such as Gabriel ReadyMount. Replace both sides of an axle and confirm fit on Amazon.
Our Quick Picks
Three quick picks: a Bilstein set for the lifted JL, a Rancho set for the stock-height JK and a loaded Gabriel strut for the Grand Cherokee. All six listings are reviewed below.

Bilstein B8 5100 Set
Front and rear 5100 shocks sized for a moderate lift.

Rancho RS5000X Set
Four-corner set for a JK at or near factory height.

Gabriel ReadyMount G57765
Complete strut, spring and mount in one assembly.
Solid Axle Wranglers Versus Strut-Front SUVs
The Wrangler JK and JL ride on solid axles front and rear, with coil springs and locating links. Each corner has a separate shock between the axle and the frame, and because the springs carry the weight, the shock only controls how fast the axle moves.
The Grand Cherokee from 2005 on and the Cherokee from 2014 on use independent front suspension with MacPherson-style struts. A strut is a damper and a structural part at once, with the coil spring and upper mount stacked on top of it. That is why these Jeeps are usually repaired with complete strut assemblies up front and ordinary shocks at the rear.
If you are not sure whether your struts are actually worn, our guide on how to tell if struts are bad walks through the bounce test, leak checks and tire wear clues before you spend money.
Lift Height, Trail Use and Daily Driving
Wrangler shocks are sold by lift range, such as 0 to 1.5 inches, 1.5 to 3.5 inches or 2 to 3 inches. A lift pushes the axle further from the frame, and a factory-length shock can top out or run short of travel. Order for the lift you actually run, front and rear, since many kits raise each end by a different amount.
Use matters as much as height. A highway Jeep does well with a quiet twin-tube or simple monotube shock, while one that sees trails or washboard roads benefits from a remote reservoir that holds more oil and sheds heat.
Best Shocks for Jeep: Six Listings by Model and Lift
Each listing below names a specific Jeep, position and lift range. Check your year, model, drivetrain and lift in the Amazon fit checker before you order, because no single shock fits every version.
1. Bilstein B8 5100 Set: Front and Rear Monotube Shocks for 2018-2025 Wrangler with 2-3 in Lift

- Listed for 2018-2025 Wrangler with 2-3 in front and rear lift
- Set of front and rear shocks
- Velocity-sensitive digressive valving
- Zinc-plated body, limited lifetime warranty
The Bilstein B8 5100 is one of the most familiar names on lifted Wranglers, and this listing is a complete front and rear set for the 2018 to 2025 Wrangler, the JL generation, with a 2 to 3 inch lift at both ends. Buying the set means all four corners come from one series and one lift range, so the axles are damped the same way.
Bilstein describes velocity-sensitive digressive valving, which is meant to react quickly to changing surfaces and keep the ride controlled both on pavement and on rough tracks. The maker says the valving is tuned for each vehicle application through road testing. The shock bodies are zinc plated to resist rust and corrosion, a useful detail for a Jeep that spends the winter on salted roads, and the 5100 series carries a limited lifetime warranty.
This set is sized for a lifted Jeep, so it is the wrong choice for a JL at factory height or one with a much taller kit. Measure or confirm your actual lift front and rear, since some kits raise each end differently. Owners of a 2018 JK carryover model should check the listing closely, and everyone should run the year, model and trim through Amazon’s fit checker before ordering.
View Bilstein B8 5100 Set on Amazon
2. Rough Country N3 23217_A: Front Shocks for 2018-2024 Wrangler JL 4WD with 0-1.5 in Lift

- Listed for 18-24 Jeep Wrangler JL 4WD, 0-1.5 in lift
- 10-stage variable valving
- Nitrogen charged with 54mm body
- Limited lifetime replacement warranty
Rough Country is better known for lift kits, but its N3 shocks are also sold on their own as replacements. This listing covers the front shocks for the 2018 to 2024 Wrangler JL 4WD with 0 to 1.5 inches of lift, which makes it a practical fit for a JL at factory height or with a small leveling spacer.
The listing describes 10-stage variable valving, a nitrogen charge and a 54mm shock body that Rough Country says helps the shock cool faster. It also mentions rubber bushings, a spring-loaded piston rod seal and military-spec fluid rated for very low temperatures, which matters on a Jeep that starts on cold Grand Rapids mornings. Rough Country backs the N3 line with a limited lifetime replacement warranty.
These are front shocks only. The matching rear set for the same JL is a separate listing, part 23218_A for 0 to 1 inch of rear lift, so plan on both if all four are worn. This is not the part for a JL with a 2 inch or taller lift, which needs a longer N3 for that range. Check your year, drivetrain and lift height in the Amazon fit checker, and replace both front shocks together.
View Rough Country N3 23217_A on Amazon

3. FOX 2.0 Performance Set: Reservoir Shocks for 2007-2016 Wrangler with 1.5-3.5 in Lift

- Listed for 2007-2016 Wrangler, 1.5-3.5 in front and rear lift
- Set of 4, parts 985-24-015 and 985-24-016
- Remote reservoir design
- One-year limited warranty
FOX builds shocks for racing, powersports and trucks, and its 2.0 Performance series is a common upgrade on lifted JK Wranglers. This listing is a set of four reservoir shocks for the 2007 to 2016 Wrangler with 1.5 to 3.5 inches of lift front and rear, sold under FOX part numbers 985-24-015 and 985-24-016.
The reservoir holds extra oil away from the shock body. On long, rough trails or washboard dirt roads, that extra volume gives heat somewhere to go, which helps the damping stay consistent where a smaller shock might start to fade. The listing says the necessary washers, bushings, reservoir clamps and nuts are included and that the factory mounting bolts are reused, while shock boots, roost shields and mounting plates are sold separately.
FOX covers this set with a one-year limited warranty, shorter than some rivals in this guide, so weigh that if the Jeep is mainly a commuter. The set is sized for a lifted JK and is not meant for a stock-height Wrangler or for the later JL. Confirm your year, model and lift in Amazon’s fit checker, and check that the reservoirs clear your tires and lines at full steering lock before the first trail run.
View FOX 2.0 Performance Set on Amazon
4. Rancho RS5000X Set: Gas Shocks for 2007-2018 Wrangler JK 4WD at Factory Height to 2 in Lift

- Listed for 2007-2018 Jeep Wrangler 4WD JK
- Set of 4, parts RS55326 and RS55328
- Factory height or 0-2 in front and rear lift
- Limited lifetime warranty, 90-day ride guarantee
A lot of JK owners never lift their Jeep, and this Rancho listing is aimed squarely at them. It is a set of four RS5000X gas shocks for the 2007 to 2018 Wrangler 4WD JK, at factory height or with up to 2 inches of lift front and rear, under Rancho part numbers RS55326 and RS55328.
Rancho describes the RS5000X as a twin-tube design with valving tuned for each vehicle. The maker says this helps soften low-speed impacts on the road while keeping control when the Jeep leaves the pavement. The listing says all the washers, bushings and nuts are supplied and the factory mounting bolts are reused, which keeps the swap simple for a home mechanic with jack stands.
Rancho backs the RS5000X with a limited lifetime warranty and a 90-day ride guarantee, a sensible safety net if you are unsure how a new shock will feel. The set is not designed for a tall lift, so look at a longer shock if your JK runs more than 2 inches. Confirm the year, model and drivetrain in the Amazon fit checker, and since this is a full set, all four corners are refreshed at once.
View Rancho RS5000X Set on Amazon

5. Gabriel Ultra ReadyMount G57765: Front Right Loaded Strut for 2010-2015 Grand Cherokee

- Listed for 10-15 Jeep Grand Cherokee
- Front right strut and coil spring assembly
- Pre-assembled, no spring compressor needed
- Stroke 5.43 in, extended length 31.69 in
The Grand Cherokee of this era uses struts up front, and when one leaks or the spring sags, a complete assembly is usually the most practical fix. This Gabriel Ultra ReadyMount listing is the front right strut and coil spring assembly for the Grand Cherokee, listed as 2010 to 2015, part number G57765.
Because the strut, spring and upper mount arrive already assembled, there is no need to compress the coil spring at home, which removes the most dangerous step of a strut job. The listing gives the stroke as 5.43 inches with an extended length of 31.69 inches and a collapsed length of 26.26 inches, along with upper and lower mount codes you can compare against your old strut. It also lists interchange part numbers for cross-checking.
This is one side only. The front left assembly is a separate listing, G57764, and both sides should be replaced together so the Jeep sits level and steers evenly. Enter the full year, trim, engine and drive type in Amazon’s fit checker, and check whether your Jeep has air suspension before ordering. Plan on a wheel alignment once both struts are installed.
View Gabriel ReadyMount G57765 on Amazon
6. Monroe Quick-Strut 273125: Strut and Coil Spring Assembly for 2014-2023 Jeep Cherokee

- Listed for 2014-2023 Jeep Cherokee
- Strut, coil spring and upper mount pre-assembled
- No spring compressor required
- Protective coating with salt spray testing
The Cherokee that returned in 2014 is a unibody crossover with front struts, so its repair looks more like a car job than a Wrangler shock swap. This Monroe Quick-Strut listing, part 273125, is a strut and coil spring assembly for the 2014 to 2023 Jeep Cherokee.
Monroe supplies the strut, an application-specific coil spring and a premium upper mount as one unit, so no spring compressor is needed. The maker says the spring is calibrated to restore factory ride height, and the upper mount is meant to keep steering smooth and reduce noise, vibration and memory steer. A protective coating and salt spray testing address rust, which is a fair concern on a crossover that sees Michigan road salt every winter.
The title does not state the side or drivetrain, and Monroe sells a companion listing, 273126, for the same years. Read the product details and the Amazon Confirmed Fit notes carefully, entering year, engine and trim, before you decide which one you need. Replace the struts on both sides of the axle together, and book an alignment afterward. This is a road-focused replacement, not a lift or off-road upgrade for a Trailhawk.
View Monroe Quick-Strut 273125 on Amazon
Model, Position and Lift at a Glance
Years and lift ranges are given the way each listing names them. Compare the part number against your own Jeep before buying.
| Listing | Jeep named | Position and lift | Suits |
|---|---|---|---|
| Bilstein B8 5100 set | Wrangler 2018-2025 | Front and rear, 2-3 in lift | Lifted JL on road and trail |
| Rough Country N3 23217_A | Wrangler JL 4WD 2018-2024 | Front pair, 0-1.5 in lift | Stock or leveled JL |
| FOX 2.0 Performance set | Wrangler 2007-2016 | Front and rear, 1.5-3.5 in lift | Lifted JK with trail use |
| Rancho RS5000X set | Wrangler JK 4WD 2007-2018 | Front and rear, 0-2 in lift | Stock-height JK daily driver |
| Gabriel ReadyMount G57765 | Grand Cherokee 2010-2015 | Front right loaded strut | Sagging or leaking WK2 front |
| Monroe Quick-Strut 273125 | Cherokee 2014-2023 | Front loaded strut, check side | Road-driven KL Cherokee |

How Michigan Roads Wear Out Jeep Dampers
Grand Rapids winters are hard on shock bodies and mounts. Road salt sits on the lower eye and the shaft seal for months, and the freeze and thaw cycle opens potholes that slam an axle into its bump stops.
Worn dampers rarely fail silently. You may hear a knock from a dry bushing, a clunk from a loose upper mount or a squeak from a strut bearing as the body rolls. Our article on why a car squeaks when going over bumps helps you separate a tired shock from a bushing or ball joint noise.

Before you settle on the best shocks for Jeep driving in salt country, look at what each maker says about corrosion, such as zinc plating or a salt spray tested coating. Makers also publish fit lookups, and FOX sorts its truck and SUV shocks by year, make and model. A rinse of the undercarriage after the salt season helps any new set last.
Doing the Swap Yourself or Booking It In
Rear shocks on any of these Jeeps, and all four corners on a Wrangler, are a common driveway job. Support the axle on stands, replace both sides of an axle together and torque the bolts to your repair manual. On a salted Jeep, soak seized lower bolts in penetrating oil the night before.
Strut fronts are a different story. A loaded strut bolts in as one unit, but a bare strut means moving the spring yourself, and a compressed coil stores a dangerous amount of energy. If you go that route, use a proper tool from our guide to the best coil spring compressor and follow its instructions exactly.

Fitting the best shocks for Jeep strut fronts changes camber and toe, so book an alignment once they are in. For a broader look at road-focused options, see our roundup of shocks and struts for daily drivers, or let us handle the job through our suspension repair service in Grand Rapids. Hendrick Hoffman, our owner, holds ASE and State of Michigan certification in steering and suspension, so Jeep ride problems get a proper look.
More Buying Guides
Frequently Asked Questions
What are the best shocks for Jeep JK models with no lift?
Pick a set listed for factory height. The Rancho RS5000X set for the 2007-2018 JK covers stock height up to a 2 inch lift, which suits a daily driven Wrangler that sees the occasional trail.
Do I need longer shocks after lifting my Wrangler?
Usually, yes. A lift moves the axle further from the frame, so order shocks sized for your lift range at each end. Stock-length shocks can top out and limit travel on a lifted Jeep.
Should Jeep shocks be replaced in pairs?
Yes. Replace both shocks or struts on the same axle together so each side damps the same way. A new part on one side and a worn one on the other can make the Jeep pull or lean.
Does a Grand Cherokee need an alignment after new struts?
Yes. Removing and refitting a front strut changes camber and toe, so book an alignment after the job to protect the tires and keep the steering straight.
Does your Jeep bounce, lean or knock over Grand Rapids potholes? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a suspension check on our contact page.
Short on daytime hours? Bring the Jeep by 456 Carrier St NE, Grand Rapids, whenever suits you and leave the keys with our after-hours drop-off.
