As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A chirp on a cold morning is often the first sign that a Honda’s accessory belt is wearing out. The best serpentine belt for Honda engines is the one that matches your engine’s rib count and length exactly, from a maker that builds belts to original-equipment standards.
Honda does not use one belt across its range. A Civic 1.8L, a CR-V 2.4L and an Odyssey V6 each take a different part, so this guide works model by model. For a wider look at belt makers, see our serpentine belt brand guide.
Quick answer
Which serpentine belt should a Honda owner buy?
Buy the belt whose listing names your Honda model and engine or replaces your Honda part number. Gates, Bando and Aisin all make Honda-specific belts: for example, Gates K070852 for a 2006 to 2011 Civic 1.8L, Bando 7PK1835 for a 2008 to 2012 Accord 2.4L and Aisin AVBAZ-00271 for Honda’s 3.5L V6.
Our Quick Picks
Three quick picks covering the Civic 1.8L, the Accord 2.4L and Honda's 3.5L V6. All six belts are reviewed below.

Gates K070852
Aramid cord belt that replaces the Honda numbers used on the 1.8L Civic.

Bando 7PK1835
Belt from the maker named on genuine Honda belts, listed for the eighth-generation Accord.

Aisin AVBAZ-00271
One belt listed across Honda's V6 minivan, SUV, truck and sedan models.
What Changes From One Honda Belt to the Next
Honda belts look alike at a glance, but a belt that is slightly off in length will either refuse to go on or sit slack against the tensioner. Four details decide the fit.
- Rib count: Honda’s four-cylinder engines covered here use 7-rib belts, while the 3.5L V6 uses a 6-rib belt. The part number usually tells you, as in 7PK or K07 for seven ribs.
- Effective length: CR-V, Element and Accord 2.4L belts differ by only a few inches, so check the listed length.
- Cord type: some Honda drives call for a stretch-resistant aramid cord, which Gates matches on its belts for them.
- Honda part number: Honda’s numbers start with 56992, 38920 or 31110, and good aftermarket listings print the ones they replace.
Finding the Right Belt Number for Your Honda
Start with the old belt. Most belts carry a part number and size on the back, and if you can still read it, compare it with the listings below.
If the print is gone, use your year, model and engine. A 2009 CR-V with the 2.4L and a 2012 CR-V with the 2.4L take different belts, because Honda changed the belt between those generations. A parts catalog or a Honda parts counter can turn your VIN into the right number.
Before you remove anything, photograph the belt routing or find the diagram on the underhood label. Routing the new belt the wrong way around one pulley is an easy mistake.
Best Serpentine Belt for Honda: Six Belts by Model
Each belt below is tied to specific Honda models by its listing or by the Honda numbers it replaces. None of them fits every Honda, so confirm your year, model and engine with the Amazon fit checker before you order.
1. Gates K070852: 7-Rib Aramid Cord Belt for the 2006-2011 Civic 1.8L

- 7-rib Micro-V belt, 15/16 in x 85 7/8 in
- Aramid cord, matching the original construction
- Replaces Honda 56992-RNA-A03 and A04
- Built to reduce noise and vibration
The Gates K070852 is a 7-rib Micro-V belt measuring 15/16 of an inch wide and 85 7/8 inches long. Its listing cross-references Honda part numbers 56992-RNA-A03 and 56992-RNA-A04, which are the numbers other sellers tie to the 2006 to 2011 Civic with the 1.8L four-cylinder engine. It also replaces Dayco 5070852 and Continental 4070852, which helps if you are comparing belts from different makers.
The main detail is the cord. Gates builds this belt with an aramid cord and describes it as an exact match for the original construction on accessory drives that call for one. Aramid resists stretch, so the belt holds its length and lets the automatic tensioner do its job without running out of travel. Gates also lists reduced noise and vibration among its aims, which matters on a Civic that has started to chirp at start-up.
This belt suits an owner who wants a part matched to the factory build from a large belt maker. It is the wrong belt for the 2012 to 2015 Civic 1.8L, which uses a 6-rib belt, and for Civics with other engines. Confirm your year, model and engine with the Amazon fit checker, and inspect the tensioner and idler while the old belt is off.
2. Bando 7PK1835: 7-Rib, 72.2 in Poly-V Belt for the 2008-2012 Accord 2.4L

- 7 ribs, 1835 mm or 72.2 in
- Listing names Honda Accord 2008-2012
- Replaces Honda 56992-R40-A01 and A02
- Synthetic rubber ribs for wear resistance
Bando’s 7PK1835 is a 7-rib Poly-V belt measuring 1835 millimeters, or 72.2 inches. The listing names the 2008 to 2012 Honda Accord and replaces Honda numbers 56992-R40-A01 and 56992-R40-A02, the belt for the 2.4L four-cylinder in that generation. It also cross-references Gates K070721 and Continental 4070722, so the size is easy to check against other brands.
Bando matters here because the genuine Honda belts on Amazon list Bando as the maker. The company sells one line of belts for both car makers and the aftermarket, so this is about as close to the dealer part as you can get without buying it from a Honda counter. The ribs are ground from a high-strength synthetic rubber compound for wear resistance, and the tensile cords are designed to carry the load without stretching.
This belt suits an Accord owner who wants an original-equipment supplier’s part at an aftermarket listing. It is not for the Accord V6, which uses a 6-rib belt, or for the 2003 to 2007 or 2013 and newer four-cylinder Accords, which take different lengths. One feature line also mentions 8 ribs, so check the 7PK size against your old belt and confirm your year, model and engine with the fit checker.

3. Aisin AVBAZ-00271: 6-Rib, 84.06 in EPDM Belt for Honda 3.0L-3.7L V6 Engines

- 6-rib EPDM belt, 84.06 in effective length
- Listed for Odyssey 2005-2017 and Pilot 2005-2015
- Also Accord V6 2003-2012 and Ridgeline 2006-2014
- Replaces Honda 38920-RCA-A03 and 56992-RV0-A01
The Aisin AVBAZ-00271 is a 6-rib EPDM belt with an effective length of 84.06 inches. Its listing covers a wide spread of Honda V6 models: the Odyssey from 2005 to 2017, the Pilot from 2005 to 2015, the Ridgeline from 2006 to 2014 and the Accord V6 from 2003 to 2012, plus several Acura models. It replaces Honda numbers including 38920-RCA-A03, 56992-R70-A01 and 56992-RV0-A01.
Aisin is a long-standing supplier to car makers, and its aftermarket belts are listed by exact effective length and rib count, which makes them easy to check. EPDM rubber resists heat and cracking better than the older neoprene belts it replaced. On these V6 engines the accessory belt also has to come off for the timing belt service, so many owners fit a new one at the same visit rather than reuse the old belt.
The listing has exclusions worth reading. It does not fit the 2011 and 2012 Accord V6 with a manual transmission, or the 2011 Crosstour V6 manual, and it rules out applications that use an 84.5-inch belt. It suits an Odyssey, Pilot or Ridgeline owner with the automatic transmission. Confirm your year, model, engine and transmission with the fit checker before you order.
View Aisin AVBAZ-00271 on Amazon
4. Aisin AVBH-00278: 7-Rib, 69.02 in EPDM Belt for the 2007-2009 CR-V 2.4L

- 7-rib EPDM belt, 69.02 in effective length
- Listed for Honda CR-V 2007-2009, L4 2.4L
- Replaces Honda 38920-RBB-E01 to E03
- Internal cords to limit stretch and slip
Aisin’s AVBH-00278 is a 7-rib EPDM serpentine belt with an effective length of 69.02 inches and a top width of 0.95 inches. The listing names two applications: the 2007 to 2009 Honda CR-V and the 2004 to 2008 Acura TSX, both with the 2.4L four-cylinder. It replaces Honda numbers 38920-RBB-E01, E02 and E03, which you may find on the old belt or in a parts catalog.
Aisin describes the belt as built to resist heat, fatigue and wear, with internal cords that limit stretching and slipping under load. That matters on a CR-V that runs the A/C hard in a humid summer and then starts cold through a Michigan winter. Because the listing gives the effective length to two decimal places, it is easy to compare with the number printed on your old belt.
This belt is a good fit for an owner of a third-generation CR-V who wants a belt listed by model rather than a universal size. It does not fit the 2010 and 2011 CR-V, which Aisin lists under a different belt, or the 2012 and newer CR-V. Confirm your year, model and engine with the Amazon fit checker, and look over the tensioner pulley while the belt is off.
View Aisin AVBH-00278 on Amazon

5. Bando 7PK1765: 7-Rib, 69.5 in OEM Quality Belt for the 2003-2011 Element

- 7 ribs, 1765 mm or 69.5 in
- Listing names Honda Element 2003-2011
- Strong tensile cords to resist stretch
- Ground synthetic rubber ribs
The Bando 7PK1765 is a 7-rib belt measuring 1765 millimeters, or 69.5 inches. Its listing names the Honda Element from 2003 to 2011, which covers every year the Element was sold, along with some Dodge Viper years that happen to share the size. All Elements use the 2.4L four-cylinder, so there is no engine split to worry about within the Honda range.
Bando builds the belt with strong tensile cords that carry high loads without stretching, and its ribs are ground from a high-strength synthetic rubber compound for wear resistance. The company points to quality awards from car makers including Honda, Toyota and GM. For an Element owner, that means a belt from the supplier named on Honda’s own branded belts, at an aftermarket listing.
Elements tend to stay in service a long time and often carry roof racks, bikes and camping gear, so the accessory drive sees plenty of hours. This belt suits an owner who wants a simple, size-matched replacement. Element belts from other makers are listed at 69.47 to 69.49 inches, which is the same size class. Confirm your year and model with the Amazon fit checker, and check the tensioner and idler before fitting it.
6. Gates K070663: 7-Rib Aramid Cord Micro-V Belt for the 2012-2014 CR-V 2.4L

- 7-rib Micro-V belt, 15/16 in x 66 3/4 in
- Aramid cord, matching the original construction
- Replaces Honda 31110-R5A-A01
- Built to reduce noise and vibration
The Gates K070663 is a 7-rib Micro-V belt measuring 15/16 of an inch wide and 66 3/4 inches long. Its listing replaces Honda part number 31110-R5A-A01, the belt that other sellers list for the 2012 to 2014 CR-V with the 2.4L four-cylinder. It also cross-references Dayco 5070663 and Continental 4070663, so you can compare it against those brands if you find one of them on the old belt.
Like the Gates belt for the Civic, this one uses an aramid cord, which Gates describes as an exact replacement for the original construction on drives that need it. The cord resists stretch, so the belt keeps its length over time and the automatic tensioner stays within its working range. Gates lists lower noise and vibration as a goal, which suits a CR-V that has started to squeal on cold starts.
This belt is for the fourth-generation CR-V up to the 2014 model year. It is noticeably shorter than the belt for the 2007 to 2009 CR-V, so the two are not interchangeable, and later CR-V years need their own check. The listing itself does not print a model name, so confirm your year, model and engine with the Amazon fit checker before ordering.
Honda Belt Lineup at a Glance
The table sorts the six belts by model. Treat it as a shortlist for the best serpentine belt for Honda models, then check each listing against your own car, since model year and transmission can change the belt.
| Honda model | Engine and years | Belt reviewed | Ribs and length |
|---|---|---|---|
| Civic | 1.8L, 2006 to 2011 | Gates K070852 | 7 ribs, about 85.9 in |
| CR-V | 2.4L, 2007 to 2009 | Aisin AVBH-00278 | 7 ribs, 69.02 in |
| CR-V | 2.4L, 2012 to 2014 | Gates K070663 | 7 ribs, about 66.8 in |
| Accord | 2.4L, 2008 to 2012 | Bando 7PK1835 | 7 ribs, 72.2 in |
| Element | 2.4L, 2003 to 2011 | Bando 7PK1765 | 7 ribs, 69.5 in |
| Odyssey, Pilot, Ridgeline, Accord V6 | 3.0L to 3.7L V6, years as listed | Aisin AVBAZ-00271 | 6 ribs, 84.06 in |

Check the Tensioner Before the New Belt Goes On
A new belt on a worn tensioner will chirp, flutter or wear out early. Bando’s accessory drive tensioner page sums up the job: it holds constant tension to stop slip and noise, damps vibration from engine firing and adjusts for belt stretch and wear. With the old belt off, spin each pulley by hand: it should turn smoothly and quietly, with no wobble or grinding. Watch the tensioner arm with the engine idling after the job, too, since an arm that bounces points to a weak spring or damper.
West Michigan winters are hard on this part of the engine. Cold rubber is stiffer, so a tired belt often squeals for the first minute on a freezing morning and then goes quiet. Road salt and slush thrown up from the wheel well also coat pulleys and speed up wear on bearings.

The Odyssey, Pilot and Ridgeline V6 engines need extra thought. These engines use a timing belt, and the serpentine belt has to come off to reach it, so it makes sense to fit a new accessory belt at the same visit. Our guide to the timing belt kit brands worth buying covers the parts for that job, and timing belt vs timing chain explains which Honda engines have which.
When a Squeal Means a Trip to the Shop
The belt drives the alternator, the A/C compressor and, on Hondas with hydraulic steering, the power steering pump. Warning signs of a failing belt include squeaking at start-up or while driving, a battery or charging light, weak A/C and a burnt rubber smell. If the belt snaps, the battery stops charging, the A/C quits and, on those hydraulic-steering models, the wheel turns heavy.
Some noises are not the belt at all. A whine that rises when you turn the wheel can point to the steering system, covered in our power steering whining noise guide, and dim lights with a weak battery may be bad alternator symptoms rather than a slipping belt.

If the belt has already come off, or the tensioner or a pulley is noisy, have the drive checked before you fit a new belt. Our timing belt and chain replacement service in Grand Rapids covers belt drives on Honda V6 engines, and we can inspect the accessory belt, tensioner and pulleys at the same time.
More Buying Guides
Frequently Asked Questions
What brand of serpentine belt does Honda use?
The genuine Honda belts listed on Amazon name Bando as the maker. Honda may source from more than one supplier over the years, so an OE-grade belt from Bando, Gates or Aisin that matches your Honda part number is a sound choice.
What is the best serpentine belt for Honda CR-V models?
It depends on the year. A 2007 to 2009 CR-V 2.4L takes a 69-inch belt such as the Aisin AVBH-00278, while a 2012 to 2014 CR-V 2.4L takes a shorter belt such as the Gates K070663. Check your year and engine before ordering.
Should I replace the tensioner with the belt?
Not always, but check it every time. If the pulley is rough or noisy, or the arm bounces at idle, replace it with the belt. On a high-mileage Honda still running its original tensioner, doing both at once saves a second job.
How often should a Honda serpentine belt be replaced?
Honda does not set one mileage for every model, so follow the inspection items in your owner’s manual or Maintenance Minder. Replace the belt sooner if it shows cracks, missing chunks, glazing or frayed edges, or if it squeals after adjustment.
Hearing a squeal from under the hood of your Honda? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a belt and tensioner check through our contact page.
If weekday hours don’t suit you, the after-hours drop-off is an option. Bring the car to 456 Carrier St NE, Grand Rapids, MI 49505, and leave it with us overnight.
