As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A Jeep sits higher than most cars, and a lift kit with bigger tires pushes the axles even further from the floor. That is why the best car jack for Jeep owners is rarely the same jack that works on a sedan. You need enough reach to get a 33 or 35 inch tire off the ground, a lift point the jack can actually grab and, for some drivers, a tool that still works on sand or gravel.
Below: garage jacks versus trail jacks, how to measure the height you need and six jacks for Wranglers, Gladiators and Grand Cherokees. If your tool chest is still thin, our list of starter car maintenance tools for beginners covers the stands, sockets and torque wrench that go with any jack.
Quick answer
What kind of jack works on a Jeep?
At home, a tall-reaching hydraulic jack such as the SUNEX 6602RJ, which lists 28.4 inches of lift, handles lifted Wranglers. On the trail, a Hi-Lift HL-485 lifts, winches and clamps from a steel bumper. A big-wheel jack like the Cat 240330 covers driveways and gravel with less fuss.
Our Quick Picks
Three jacks that cover the main Jeep situations: trail recovery, a lifted rig in the garage and gravel or dirt at home. All six are reviewed in full below.

Hi-Lift HL-485
The classic off-road ratcheting jack that also pulls and clamps when a Jeep gets stuck.

SUNEX 6602RJ
A tall-reaching big-wheel jack that works on concrete and on firm gravel alike.

Cat 240330 Big Wheel
Large wheels and a skid plate let it work where a standard floor jack would sink.
Garage Jack or Trail Jack: Decide Where You Will Lift
Start with where the Jeep will be when you need the jack. A hydraulic floor jack rolls on casters and wants smooth concrete. A ratcheting high-lift jack stands on a small foot and climbs a steel bar, so it can raise a stuck Jeep in mud but needs a solid steel lift point and careful hands.
- Garage work: tire rotations, brake checks and suspension inspections call for a hydraulic floor jack with enough reach for your axle height.
- Trail and roadside: a flat on a two-track or a stuck wheel calls for a jack you can carry.
How Much Lift Height a Lifted Jeep Needs
Capacity is rarely the limit on a Jeep, since a jack lifts one corner or one axle end at a time. Height is the real test. Measure from the floor to the bottom of the axle tube or the lift point in your owner’s manual, then add the distance the tire must travel before it clears the ground, which grows as the suspension droops.
On a stock Wrangler or Gladiator, a jack that tops out near 20 inches may be enough, but measure first. A Jeep with a lift kit and tall tires may need 24 inches or more once the axle hangs down, which is where tall-reaching jacks and saddle adapters earn their place. A Grand Cherokee is a unibody vehicle, so check its manual for the body lift points rather than reaching for the axle.
If a lower car shares the garage, our guide to the low profile floor jack for cars with tight clearance covers entry height.
Best Car Jack for Jeep: Six Jacks Up Close
Every capacity and height below comes from the maker’s page or the Amazon listing, so check them against your own measurements.
1. Hi-Lift HL-485: 48 Inch All-Cast Ratcheting Jack for Lifting, Winching and Clamping

- 48 inch all-cast iron bar jack
- 7,000 lb tested, 4,660 lb rated capacity
- Top winch connector clamp
- Two-piece handle and socket
The Hi-Lift HL-485 is a 48 inch ratcheting bar jack made from cast iron parts, and the maker says it is the only all-cast jack still produced. On the Hi-Lift All-Cast Jack product page, the company lists a 7,000 lb tested capacity and a 4,660 lb rated capacity, along with a lifetime parts support warranty once the jack is registered.
Unlike a hydraulic jack, it climbs a steel bar one notch at a time as you work the long handle. That lets it raise a corner of a Jeep stuck in mud or sand, and with the top winch connector clamp it can also act as a hand winch or a spreader. The powder coated finish and zinc-plated hardware help it cope with wet trail days and salty roads, and the rated load and operating instructions are printed on the handle.
The trade-off is that it needs a solid steel lift point, such as an aftermarket bumper or rock slider, because a factory plastic bumper cover will not take the load. It also demands care: the handle can kick if the load shifts. For garage tire rotations, a hydraulic floor jack is easier and calmer.
2. Hi-Lift HL-604: 60 Inch Cast/Steel Ratcheting Jack with Shear Bolt Overload Protection

- 60 inch cast and stamped steel bar
- Shear bolt stops loads past 7,000 lb
- 750 lb clamping capacity
- Black jack with red handle
The Hi-Lift HL-604 uses the same design as the all-cast model, but four of its parts are high-strength stamped steel rather than cast iron. Hi-Lift says it forms those parts in-house and gives the cast/steel jack the same 7,000 lb tested and 4,660 lb rated capacity. The 60 inch bar is the longest size the company offers in this line.
That extra length matters on a Jeep with a tall lift and large tires. When the suspension droops as you raise the bumper, a shorter bar can run out of travel before the tire leaves the ground, and the 60 inch version gives more room to finish the job. The listing notes a shear bolt that keeps the jack from being used on loads over 7,000 lb and a clamping capacity of 750 lb, which helps when you use it as a spreader or clamp.
A 60 inch bar is awkward to mount and store, so measure your hood, roof rack or bed mount before you order. On a stock Wrangler, Gladiator or Grand Cherokee, the extra height is unnecessary, and the 48 inch size or a hydraulic jack makes more sense. The same steel lift point rules apply as with every ratcheting jack.

3. SUNEX 6602RJ: 2 Ton Big Wheel Jack with 28.4 Inch Lift Height and Steel Skid Plate

- 2 ton capacity
- 28.4 in. listed lift height
- 4-position locking height adapter
- Wrap-around steel skid plate
The SUNEX 6602RJ is a 2 ton hydraulic jack with large composite wheels and a tall reach. Its listing quotes a 28.4 inch lift height, which is enough to raise the axle of many lifted Jeeps far enough for a tall tire to clear the ground. SUNEX also states that it meets the ASME PASE standard for portable automotive service equipment.
Height comes from the jack itself plus a 4-position locking extension with a rubber grip pad, so you can set the saddle close to the axle before pumping. A full-length wrap-around steel skid plate spreads the load and helps keep the jack from sinking or shifting on gravel. Dual pistons speed up the rise, while solid steel axles and stainless hardware help it stand up to wet, salty Michigan winters.
The 2 ton rating is lower than the 3 ton jacks here, but a jack lifts only one corner or one axle end, so it still suits most Wrangler and Gladiator work. A handle lock detent makes it easier to roll across the driveway. It is not a low-entry jack, so pair it with a different jack if a lowered car shares the garage.
4. Cat 240330: 3 Ton Big Wheel Off-Road Hybrid Jack with 6 to 21.5 Inch Lift Range

- 3 ton (6,000 lb) capacity
- Lift range 6 to 21.5 in.
- Adapter adds 7.75 in. of height
- Bottom skid plate for stability
The Cat 240330 is a hydraulic floor jack built for ground that is not smooth concrete. Its listing gives a 3 ton (6,000 lb) capacity and a lift range of 6 to 21.5 inches, and an included adapter adds 7.75 inches to the maximum height. That extra reach helps on a Jeep whose axle sits high once the tire starts to hang.
The large wheels roll over gravel and packed dirt more easily than small casters, and a bottom skid plate spreads the load so the jack stays stable on uneven ground. The frame mixes steel and aluminum to trim weight compared with an all-steel jack of similar size. A dual-piston pump brings it to full height in about 7 pumps, according to the listing, which shortens the time you spend kneeling on a gravel driveway.
With a 6 inch starting height, it will not fit under low cars, so it is a poor choice if a sports car shares the garage. Soft sand still calls for a board under the skid plate. For a Wrangler, Gladiator or Grand Cherokee that sees both the driveway and the campsite, though, it is a practical middle ground between a shop jack and a trail jack.
View Cat 240330 Big Wheel on Amazon

5. Cat Wheelie 980883ECE: 2 Ton Off-Road Trolley Jack with Oversized Wheels and Saddle Extension

- 2 ton capacity
- Lift 6 to 14.5 in. (9 to 17.5 in. with extension)
- Oversized 4 in. wheels
- Handle stored on the jack
The Cat Wheelie is a compact 2 ton trolley jack meant to travel with the vehicle. Its listing gives a lift range of 6 to 14.5 inches on its own and 9 to 17.5 inches with the included saddle extension. Those numbers suit a stock-height Wrangler, Gladiator or Grand Cherokee better than a heavily lifted one, so measure your own lift point first.
Four-inch wheels give it more grip and roll on dirt and gravel than the small casters on a garage jack. Padded spring steel clips hold the handle against the body, so the parts stay together when the jack rides around in the cargo area. That small detail matters on a washboard two-track, where loose tools tend to scatter.
The trade-off is reach and size. With a 17.5 inch top end, it can run short on a Jeep with a tall lift once the axle droops, and it is less stable than a full-size jack on soft ground, so carry a board to set it on. As a roadside or trail tire-change jack for a mostly stock Jeep, though, it is light enough that you will actually bring it.
View Cat Wheelie 2 Ton on Amazon
6. BIG RED 12 Ton: Welded Hydraulic Bottle Jack with 8.94 to 18 Inch Lift and Storage Case

- 12 ton (24,000 lb) capacity
- Lift range 8.94 to 18 in.
- 3.15 in. adjustable extension screw
- Storage case included
The BIG RED 12 Ton is a welded hydraulic bottle jack that comes with its own carrying case. Its listing gives a 12 ton (24,000 lb) capacity and a lifting range of 8.94 to 18 inches, plus an extension screw that adjusts by 3.15 inches before you start pumping. That compact shape is the main reason Jeep owners carry one.
On a Wrangler or Gladiator with solid axles, a bottle jack placed under the axle tube near the spring perch can raise a wheel without needing a steel bumper. The serrated, heat-treated saddle grips the load, and the glide-action pump lifts with short, easy strokes. The case keeps the jack and handle together and stops it from rolling around behind the rear seat on rough roads.
The 8.94 inch minimum height is the catch: with a flat tire on a stock Jeep, the axle may sit too low for it to fit, so check the gap at home before you rely on it. It also needs a flat, firm base, so carry a small board for dirt or sand. On a unibody Grand Cherokee, use the body lift points in your manual instead of the axle.
View BIG RED 12 Ton Bottle Jack on Amazon
Which Jack Suits Your Jeep and Driving
The table matches each jack to the job it handles well, which is the quickest way to find the best car jack for Jeep use in your own driveway or on the trail.
| Jack | Type | Listed lift range or height | Good fit for |
|---|---|---|---|
| Hi-Lift HL-485 | Ratcheting, all-cast | 48 in. bar | Trail recovery from steel bumpers |
| Hi-Lift HL-604 | Ratcheting, cast/steel | 60 in. bar | Tall lifts and big tires |
| SUNEX 6602RJ | Hydraulic, big wheel | Up to 28.4 in. | Lifted Jeeps, garage or gravel |
| Cat 240330 Big Wheel | Hydraulic, big wheel | 6 to 21.5 in. (plus 7.75 in. adapter) | Gravel driveways, firm dirt |
| Cat Wheelie 2 Ton | Compact trolley jack | 6 to 14.5 in. (9 to 17.5 in. with extension) | Stock Jeeps, carried on board |
| BIG RED 12 Ton Bottle | Hydraulic bottle jack | 8.94 to 18 in. | Axle lifting, carried on board |

If the Jeep stays on stock suspension and you mostly rotate tires at home, the Cat 240330 or the Cat Wheelie is enough. Step up to the SUNEX once you install a lift, and save the ratcheting jack for owners whose Jeep already wears steel bumpers or rock sliders.
Safe Lifting and Michigan Care for Jeep Jacks
No jack on this list is a work support. Once a tire is off the ground, place rated jack stands under the axle or frame on both sides you raised, lower the Jeep onto them and keep the jack snug as a backup. Chock the wheels that stay down, and never crawl under a vehicle held by a ratcheting jack.

West Michigan road salt clings to a jack carried all winter, so rinse and dry it after snowy trips and keep a ratcheting jack’s climbing pins lightly oiled. Cold hydraulic oil also makes a floor jack rise slowly in an unheated garage.
- On sand or soft soil, set a jack base or a thick board under the foot so it cannot sink.
- Read the maker’s instructions before first use; Hi-Lift posts its jack instruction manuals online.
- Lift only at the points your owner’s manual shows, and keep plastic bumper covers out of the jack’s path.
When a Lift Beats a Jack
Work that needs the whole Jeep in the air, such as tracing a death wobble, replacing worn steering parts or checking a rusty frame, goes faster and safer on a two-post lift. Our suspension and steering repair in Grand Rapids handles that kind of job.

Lifted Jeeps wear suspension parts faster, so keep to your manual’s service schedule. Our factory scheduled maintenance in Grand Rapids puts the Jeep on a lift for those checks, with a clear view of bushings, boots and leaks.
More Buying Guides
Frequently Asked Questions
What is the best car jack for Jeep owners with a lift kit?
A tall-reaching hydraulic jack suits most lifted Jeeps at home, because it can clear the axle droop that tall tires add. The SUNEX 6602RJ lists a 28.4 inch lift height. Measure your own axle height before you buy.
Is a Hi-Lift jack safe to use on a Jeep?
It can be, when you lift from a solid steel point such as an aftermarket bumper or rock slider and follow the maker’s instructions. Keep your head out of the handle’s path, and never work under a Jeep held only by a ratcheting jack.
Can I use a bottle jack under a Jeep axle?
On solid-axle models like the Wrangler and Gladiator, a bottle jack under the axle tube near the spring perch is a common trail method. Use a flat, firm base, and check that the jack’s minimum height fits under the axle with the tire flat.
Rather skip the jacking and crawling altogether? Phone 456 AutoFix at 616-279-3832 between 8am and 5pm, Monday through Friday, or set up a visit through our contact page.
If your workday overlaps our hours, park the Jeep at 456 Carrier St NE, Grand Rapids, MI 49505, and hand the keys over through our after-hours drop-off.
