As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A growl from one front corner that rises with speed is the classic sign of a tired hub on a half-ton Ram. The best wheel bearing for Ram 1500 trucks depends first on which generation you own, then on 2WD or 4WD, lug count and wheel size.
Below are six parts sorted by generation, plus the rear axle bearing. If you are not sure the noise is a bearing yet, our guide to wheel bearing noise symptoms is the place to start.
Quick answer
Which wheel bearing fits your Ram 1500?
Start with the generation. A 2019 or later new-body truck takes a 6-lug hub such as MOOG 515178 or the A-Premium 4WD unit. A 2012 to 2018 truck or a Ram 1500 Classic takes the 5-lug SKF BR930858 or the TRQ pair. Confirm drive type, wheel size and VIN before ordering.
Our Quick Picks
Three quick picks: the MOOG 515178 for the 2019 and later new-body Ram 1500, the SKF BR930858 for 2012 to 2021 5-lug 4×4 trucks including the Classic, and the National 6410 rear bearing. All six parts are reviewed below.

MOOG 515178
A sealed MOOG hub for the redesigned half-ton.

SKF BR930858
An SKF hub for 5-lug trucks, Classic included.

National 6410
An OE-style rear bearing for the axle tube.
Three Ram 1500 Generations, Three Different Hubs
Ram has sold more than one half-ton at the same time since 2019. The redesigned truck, often called the new body or DT, uses a 6-lug wheel pattern and its own front hub. The older design carried on as the Ram 1500 Classic, and it keeps the 5-lug hub from the 2012 to 2018 trucks.
That overlap is the most common reason owners order the wrong part. A 2021 Ram 1500 and a 2021 Ram 1500 Classic look alike in a parts search, yet their hubs are not interchangeable. Count your lug nuts before anything else: five points to the older design, six to the new body.
Hub Noise, Wobble and the ABS Light
A front hub on a Ram is a sealed unit: the bearing, flange, studs and usually the ABS sensor come as one assembly that bolts to the steering knuckle. When it wears, you typically hear a hum that changes as you sway the truck left and right on the highway.
Because the speed sensor lives in the hub on these trucks, a damaged sensor wire or tone ring can also switch on the ABS and traction lights. MOOG’s own page on MOOG hub assemblies notes how hard road conditions are on these parts and how much depends on sealing out water, dirt and other contaminants. For typical service life and what shortens it, see our article on how long wheel bearings last.
Best Wheel Bearing for Ram 1500: Six Parts by Generation
Each listing below covers a specific range of Ram 1500 trucks and none fits every year. Enter your year, cab, drive type, engine and wheel size in Amazon’s fit checker, and if anything is unclear, confirm the part number against your VIN with a parts counter before you order.
1. MOOG 515178: Front Wheel Bearing and Hub Assembly for 2019-2023 Ram 1500

- Listed for 2019-2023 Ram 1500
- Quad lip seal against moisture and debris
- Rust resistant hub with secure studs
- Sealed bearing, bolt-on assembly
The MOOG 515178 is a front wheel bearing and hub assembly for the redesigned Ram 1500. Its compatibility notes name the 2019 to 2023 model years, and the title also mentions 2024, so check your exact year in the fit checker. It is a bolt-on unit, so the bearing, flange and studs arrive as one sealed piece that mounts to the steering knuckle. MOOG lists other part numbers for this truck, so drive type matters.
MOOG, a DRiV brand, builds this hub around a quad lip seal meant to keep water and grit away from the bearing, and describes the hub as rust resistant with secure studs. The listing also calls it a noise-free design with a sealed bearing for a quiet ride at highway speed. On a truck that spends its winters on brined roads, the seal is the feature that matters most for how long the new hub lasts.
This hub suits a stock new-body Ram 1500 with a hum, wobble or ABS fault traced to one front corner. It is not a part for a Ram 1500 Classic, which uses a 5-lug hub. One bullet on the Amazon page mentions other makes, which looks like a listing error, so rely on the confirmed fit bar and your VIN rather than the bullet text.
2. A-Premium Front Hub Assembly: 6-Lug 4WD Hub with ABS for 2019-2023 Ram 1500

- 2019-2023 Ram 1500, 4WD only
- 6 lugs, ABS sensor included
- Not for trucks with 22 inch wheels
- Pre-greased, double-lip seal ring
The A-Premium front wheel bearing and hub assembly is listed for the 2019 to 2023 Ram 1500 with 4WD. The listing is specific about one exclusion: it does not fit trucks equipped with 22 inch wheels, which use a different hub. It fits either front side, has six wheel studs and a three-hole mounting flange, and the front axle shaft slides straight into its splined center.
The specification list names GCr15 bearing steel and 65Mn steel, a pre-greased bearing, a double-lip seal ring and a built-in ABS speed sensor. A-Premium cross-references the numbers 68237141AC and 515179, which helps when you compare this hub against the part number on your old one or on a parts store receipt. The studs are made to the original specification, so your current rotor, wheels and lug nuts carry over.
This is a sensible choice for a 4WD new-body Ram 1500 on any factory wheel size except 22 inch, where one hub has started to hum or let the tire rock. It is not for 2WD trucks, the Classic or 22 inch wheel packages. Check your wheel size on the tire placard or window sticker, then confirm the fit with your VIN before you order.
View A-Premium Ram 1500 4WD Hub on Amazon

3. SKF BR930858: Front Hub Bearing Assembly for 2012-2021 Ram 1500 4×4, 5 Lug

- Ram 1500 2012-2021 4×4, 5-lug
- Sealed spindle hub bearing assembly
- Meets or exceeds OE specifications
- QR code links to SKF instructions
The SKF BR930858 is a front wheel hub bearing assembly for 5-lug Ram 1500 4×4 trucks, listed for 2012 to 2021. That range covers the 2012 to 2018 half-ton and the early years of the Ram 1500 Classic, which kept the same front hardware after the redesign. It is sold as a single hub, so buy a second one if both front corners are worn.
SKF says the kit includes the components needed for a complete wheel bearing replacement and that the part meets or exceeds OE specifications. A QR code on the box label leads to SKF’s installation instructions and technical details, which is handy for axle nut and bolt torque. SKF also states plainly that the hub should be fitted by a knowledgeable mechanic with the correct tools, following both its instructions and the vehicle procedure.
This hub suits a 4×4 Ram 1500 or Classic with a growl, steering wheel shimmy or ABS light traced to a front hub. It is not a part for the 6-lug new-body truck. The BR930858 number also shows up in the TRQ pair’s cross-reference list below, so both listings target the same application. Confirm 4×4, lug count and ABS fit in the checker first.
4. TRQ Front Wheel Bearing and Hub Set: Driver and Passenger Hubs for Ram 1500 and Classic

- 2012-2018 Ram 1500, 2019-2022 Classic
- Includes driver and passenger hubs
- Pre-assembled, direct replacement
- Cross-references 515151 and HA590515
The TRQ front wheel bearing and hub assembly set includes one driver side and one passenger side hub for the 2012 to 2018 Ram 1500 and the 2019 to 2022 Ram 1500 Classic. Buying both front hubs in one box makes sense on a high-mileage truck, since the second side has covered the same miles and the same winters as the one that failed.
The listing gives a long reference list, including 4779829AD and 68230055AB along with 515151, BR930858 and HA590515. Those numbers make it easier to match the set to what is on your truck now. TRQ describes the hubs as pre-assembled direct replacements that need no modification, and it backs its parts with a large library of DIY install videos, which helps if you plan to do the work in your own garage.
This set suits a 5-lug Ram 1500 or Classic owner who wants both front hubs replaced in a single job. It is not for the 6-lug new-body truck. The TRQ listing asks buyers to check the Amazon confirmed fit bar and its compatibility chart, and that step matters here because drive type and ABS options vary across these years. Torque the hubs to the factory figures after installation.
View TRQ Ram 1500 Hub Pair on Amazon

5. Detroit Axle Front Hub Pair: 2 Wheel Bearing Hubs for 2009-2011 Ram 1500

- 2009-2010 Dodge Ram 1500, 2011 Ram 1500
- Trucks built after 12/08/08 only
- 5 lugs, 3-bolt triangular flange
- ABS sensor wire, left and right hubs
The Detroit Axle front wheel bearing hub pair is listed for the 2009 and 2010 Dodge Ram 1500 and the 2011 Ram 1500. The fitment note carries an important limit: it fits trucks built after December 8, 2008. Early 2009 trucks built before that date can use different front hardware, so check the build date on the label in the driver door jamb before you order.
The kit contains two front hubs, one for each side. Each has five lugs, a 3-bolt triangular mounting flange and an ABS sensor with its own wire. Detroit Axle says the hubs go through impact, wear and fatigue testing to check quality and durability. Getting both sides in one box keeps the front end matched on a truck that is now well over a decade old.
This pair suits an older half-ton that is still in daily use and has started to hum, wander or wear its front tires unevenly. It is not for 2012 and later trucks. On a high-mileage truck from these years, expect the old hubs to be rusted firmly into the knuckles, so set aside time and penetrating oil, and confirm fit with your VIN first.
View Detroit Axle 2009-2011 Hub Pair on Amazon
6. National 6410: Rear Wheel Bearing for 2011-2021 Ram 1500

- Listed for 2011-2021 Ram 1500
- Also 2007-2010 Dodge Ram 1500
- Controlled heat process for strength
- Engineered to meet OE specifications
The National 6410 is a rear wheel bearing listed for the 2011 to 2021 Ram 1500 and the 2007 to 2010 Dodge Ram 1500. The same part also appears for the Dodge Durango, Chrysler Aspen, Dodge Nitro and Jeep Liberty in certain years. Unlike the front hubs above, it is not a bolt-on assembly: on these trucks the rear bearing sits in the end of the axle tube and rides on the axle shaft.
National, a DRiV brand, describes the bearing as made from premium-grade steel with a controlled heat process for strength, and engineered to meet OE specifications. The listing asks buyers to fill in year, make, model, engine and trim in the confirmed fit bar and to read any qualifier notes, which matter here because rear axle options vary across this long run of years.
This bearing suits a Ram 1500 with a rear hum that changes with speed, or a rear axle seal that keeps leaking gear oil. Plan on a new axle seal and fresh gear oil with the job. Replacing it means pulling the axle shaft and pressing the bearing in, so it is a job for experienced DIYers or a shop, and it is not a fix for a front hub noise.
Matching Each Part to Your Truck
Choosing the best wheel bearing for Ram 1500 use is mostly a fit question, so find your truck here, then run the listing through the fit checker.
| Your truck | Listing to check | Position and quantity | Watch for |
|---|---|---|---|
| 2019 to 2023 Ram 1500 (new body) | MOOG 515178 | Front, one hub | Confirm 2WD or 4WD in the fit checker |
| 2019 to 2023 Ram 1500 4WD (new body) | A-Premium 4WD hub | Front, one hub | Not for trucks on 22 inch wheels |
| 2012 to 2021 Ram 1500 4×4, incl. Classic | SKF BR930858 | Front, one hub | 5-lug trucks only |
| 2012 to 2018 Ram 1500 or 2019 to 2022 Classic | TRQ hub pair | Front, left and right | Check drive type and ABS fit |
| 2009 to 2011 Ram 1500 | Detroit Axle pair | Front, left and right | Built after 12/08/08 only |
| 2011 to 2021 Ram 1500 (rear) | National 6410 | Rear, one bearing | Needs a new axle seal too |

Salt, Slush and Hubs That Won’t Come Out
Grand Rapids winters are a big part of why Ram hubs fail here, and no part makes the best wheel bearing for Ram 1500 trucks if its seal lets salt water in. Brine and slush pack around the knuckle from November to March, and once a seal hardens, water gets into the bearing and pits the races. A truck that sits in a driveway between short winter trips gives that moisture plenty of time to work.
The same salt welds the old hub into the knuckle with rust. Even with the bolts out, a seized hub can refuse to move, and hammering on it risks the knuckle, the ABS sensor and the CV axle splines. Soak the joint with penetrating oil well ahead of time and use a proper puller rather than a hammer.

DIY Swap or a Shop Job
A bolt-on front hub is a fair job for a careful DIYer with a breaker bar, a large axle nut socket, a torque wrench and solid jack stands. Rear axle bearings are a different job: the axle shaft has to come out and the bearing is pressed, which is where a wheel bearing press kit and some experience come in.
While the front end is apart, check the rest of it for play. Worn ball joints for Ram 1500 trucks can feel and sound a lot like a bad hub.

A seized hub, a rear axle bearing or a noise you cannot pin to one corner are good reasons to bring the truck in. Our wheel bearing replacement service in Grand Rapids covers front hubs and rear bearings on foreign and domestic vehicles. Hendrick Hoffman, who runs the shop and leads the work in the bays, has been in automotive service since 2005, and our about us page lists his certifications.
More Buying Guides
Frequently Asked Questions
Does a Ram 1500 Classic use the same hub as the new-body Ram 1500?
No. The Classic keeps the 5-lug hub from the 2012 to 2018 trucks, while the 2019 and later new-body truck uses a 6-lug hub. Count the lug nuts and check the model name on your registration before you order.
Should I replace both front hubs on my Ram 1500 at once?
It is not required, but on a high-mileage truck the other side has seen the same miles and the same salt. Doing both in one visit saves a second round of labor and keeps the two sides matched.
Can a bad hub turn on the ABS light on a Ram 1500?
Yes. The front wheel speed sensor is built into the hub on these trucks, so a failed sensor, a damaged wire or excess bearing play can set an ABS or traction control warning. A scan for the stored code shows which corner to check.
Is the 4WD front hub different from the 2WD hub?
On many Ram 1500 years, yes. The 4WD hub has a splined center for the front axle shaft, and some listings also split by wheel size. Enter your exact drive type and wheels in the fit checker before you buy.
Hearing a hum that grows with every mile on your Ram? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a wheel bearing inspection through our contact page.
If the workday keeps you busy, our after-hours drop-off lets you leave the truck at 456 Carrier St NE in Creston and we will take it from there.
