As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A pickup loads each front hub harder than a car does, and a tired bearing shows it with a growl that climbs with road speed. The best wheel bearings for trucks are hub assemblies built for your exact truck, drivetrain and axle, from a maker that states what the listing covers.
Below are the details that separate one truck hub from another and six listings for the F-150, Super Duty, Ram 1500, Ram 2500, Tundra and Titan. Not sure the noise is a bearing? Our guide to wheel bearing noise symptoms helps you narrow it down first.
Quick answer
Which wheel bearing should I buy for my truck?
Start with the listing that names your truck, model years and drivetrain, then compare brands. MOOG, Timken, TRQ and Detroit Axle all sell complete front hubs for popular pickups. Check 2WD or 4WD, single or dual rear wheels and the ABS sensor type, and confirm the fit in Amazon’s checker.
Our Quick Picks
Three listings that cover the most common truck jobs: a half-ton Ford 4×4, a heavy-duty Ram and a Tundra that needs both sides done.

Detroit Axle F-150 4WD Hub Pair
Both front hubs for a 2015-2017 F-150 4×4 in one box.

MOOG 515162
A MOOG front hub for the 2014-2018 Ram 2500 and Ram 3500.

TRQ Tundra Front Hub Pair
Both front hubs for the second-generation Tundra and Sequoia.
What Makes One Truck Hub Different From the Next
Most modern pickups use a bolt-on front hub assembly: bearing, flange and wheel studs in one sealed unit that bolts to the steering knuckle. All six picks below are complete front hubs.
Two hubs can look alike and still refuse to swap, so match these points:
- Drivetrain: a 4WD hub has a splined center for the front axle shaft, while a 2WD hub may have a plain center or none at all.
- Single or dual rear wheels: heavy-duty trucks often list SRW and DRW models separately, even for the front hub.
- ABS sensor: some hubs carry the sensor and its wire, and others read a tone ring with a separate sensor.
- Lug count and flange: 5, 6 or 8 lugs, and a triangular, square or rectangular bolt pattern to the knuckle.
Read the year range and any trim exclusions too, since hubs can change mid-generation. For a brand-level view, see our rundown of the wheel hub assembly brands and the numbers behind them compares the major makers.
Lifted Trucks, Big Tires and Towing Loads
People searching for the best wheel bearing for lifted trucks usually run bigger tires. A heavier tire and a wheel with more outward offset move the load away from the bearing and add leverage on the races. Wheel spacers do the same.
None of these hubs is a lift-specific part. Buy the hub listed for the stock truck, keep wheel offset near factory and check for play more often, and give trucks that tow or plow the same attention.
Best Wheel Bearings for Trucks: Six Hubs by Model
Each listing below is an example for the truck its Amazon title names. A different year, cab, drivetrain or rear-wheel setup can take another number, so use Amazon’s fit checker before you order.
1. Detroit Axle 4WD Front Hub Pair: Two Wheel Bearing Hubs for 2015-2017 F-150

- Two front hub assemblies in the kit
- Lists 2015-2017 Ford F-150, 4WD only
- 6 lugs, sensor-wire ABS, 4-bolt square flange
- Impact, wear and fatigue tested; 10-year warranty
This Detroit Axle kit puts two front wheel bearing and hub assemblies in one box, and the listing names the 2015, 2016 and 2017 Ford F-150 with four-wheel drive only. That makes it a direct option for the aluminum-body F-150 when both front corners have covered the same high miles and you would rather do the pair in one visit.
The listing gives the hub details you need to compare against your old part: six lugs, an ABS sensor with its own wire, and a four-bolt square flange that mounts to the knuckle. Detroit Axle says the hubs go through impact, wear and fatigue testing, and the listing states a 10-year warranty. Because each hub arrives with the bearing, flange and studs already assembled, the job is a bolt-off, bolt-on swap with no press needed.
This kit suits an F-150 owner with a growl that changes as the truck sways through long highway curves, or one who found play at both front wheels. It does not fit a 2WD F-150, and a 2018 or later truck uses a different hub. Confirm your year, cab, drivetrain and engine in Amazon’s fit checker before ordering, and torque the axle nut to Ford’s figure.
View Detroit Axle F-150 4WD Hub Pair on Amazon
2. Detroit Axle 4WD Front Hub Pair: Two 8-Lug Wheel Bearing Hubs for 2017-2022 Super Duty

- Two front hub assemblies in the kit
- Lists 2017-2022 F-250 and F-350 Super Duty, 4WD
- F-350 coverage is single rear wheel (SRW) only
- 8 lugs, sensor-wire ABS, square flange; 10-year warranty
This Detroit Axle kit holds two front wheel bearing and hub assemblies, and the listing names the 2017 to 2022 Ford F-250 Super Duty with four-wheel drive and the F-350 Super Duty with four-wheel drive and single rear wheels. That covers a long run of current-body heavy-duty Fords, many of which now have enough miles for front hub wear to show.
The listing spells out the hub specs: eight lugs, an ABS sensor with its own wire and a square flange that bolts to the steering knuckle. Each hub comes assembled with the bearing and studs, so the swap needs no press. Detroit Axle says the parts go through impact, wear and fatigue testing, and the listing states a 10-year warranty. Getting both sides in one box makes sense on a three-quarter or one-ton truck that has carried the same plow or trailer on both corners.
This pair suits a Super Duty owner who tows, plows or runs the truck hard for work and hears a growl or feels play at the front. It is not listed for 2WD trucks or for an F-350 dually, and an older Super Duty uses different hubs. Confirm your year, drivetrain and rear-wheel setup in Amazon’s fit checker, and torque everything to Ford’s figures.
View Detroit Axle Super Duty 4WD Hub Pair on Amazon

3. MOOG Front Wheel Bearing and Hub Assembly: Ram 1500 Hub with Quad Lip Seal

- Single front hub assembly
- Lists 2012-2018 Ram 1500, 2019-2022 1500 Classic
- Sealed bearing with quad lip seal
- Studs installed, rust-resistant hub
This MOOG front wheel bearing and hub assembly is listed for the 2012 to 2018 Ram 1500 and the 2019 to 2022 Ram 1500 Classic, which carried the older body on after the redesign. MOOG is part of DRiV, and the listing covers one hub, so you can replace a single side or order a second for the pair.
The listing describes a sealed bearing meant to run quietly, a quad lip seal that keeps moisture and grit out, a rust-resistant hub and wheel studs already in place. MOOG also points to an advanced raceway design in the title. For a truck that spends winters on salted roads, the seal and the coated hub are the details worth reading, since water past the seal is what ends most bearings early.
This hub suits Ram 1500 owners who hear a hum at highway speed or feel looseness when they rock the front tire. It does not cover the newer Ram 1500 body sold from 2019, and some special trims can use different parts, so read the fitment notes closely. Confirm your year, trim and drivetrain in Amazon’s fit checker before you buy, and torque the axle nut to the Ram service figure.
View MOOG Ram 1500 Front Hub on Amazon
4. MOOG 515162: Front Wheel Bearing and Hub Assembly for 2014-2018 Ram 2500

- Single front hub assembly
- Lists 2014-2018 Ram 2500, 2013-2018 Ram 3500
- Sealed bearing with quad lip seal
- Studs installed, rust-resistant hub
MOOG 515162 is a front wheel bearing and hub assembly, and its listing names the 2014 to 2018 Ram 2500 along with the 2013 to 2018 Ram 3500. These heavy-duty Rams often spend their lives towing trailers or pushing a plow, and that work loads the front hubs far harder than daily commuting does.
MOOG lists the same core features here as on its lighter hubs: a sealed bearing designed for quiet running, a quad lip seal against water and dirt, a rust-resistant hub and studs fitted at the factory. The hub arrives as a complete unit, so you bolt it to the knuckle rather than pressing a bearing. You buy it as a single part, which keeps costs down when only one side is worn and lets you add a second hub when both have high miles.
This hub suits Ram HD owners who notice a growl from the front, uneven wear on one front tire or an ABS light tied to a wheel speed sensor. It is not the part for a Ram 1500, and a 2019 or later Ram 2500 uses a different number. Confirm your year, drivetrain and rear-wheel setup in Amazon’s fit checker, then follow the Ram torque specs.

5. TRQ Front Wheel Bearing and Hub Assembly Set: Driver and Passenger Hubs for Tundra

- Driver and passenger front hubs
- Lists 2007-2021 Tundra, 2008-2022 Sequoia
- Pre-assembled, direct-fit replacement
- Limited lifetime warranty per listing
This TRQ set includes a driver side and a passenger side front wheel bearing and hub assembly, and the listing title names the 2007 to 2021 Toyota Tundra and the 2008 to 2022 Sequoia. Buying both hubs together suits the second-generation Tundra, which has been on the road long enough for many trucks to need both front bearings.
The listing gives a long string of reference numbers, including a Toyota part number and cross-references such as 515202, 950-002 and BR930979, which helps you match it to the hub already on the truck. TRQ describes the hubs as pre-assembled direct-fit replacements and points owners to its library of DIY repair videos. The listing states a limited lifetime warranty against defects in materials and workmanship, which excludes normal wear.
This pair suits a Tundra owner with a hum at highway speed, play at both front wheels or a truck that has seen many salted winters. The listing title does not split 2WD and 4WD trucks, so check the drivetrain details in the fitment chart. Confirm your year, cab and drivetrain in Amazon’s fit checker before you order, and torque the hub bolts and axle nut to Toyota’s figures.
View TRQ Tundra Front Hub Pair on Amazon
6. Timken SP500703: Preset, Pre-Greased and Pre-Sealed Front Hub for Nissan Titan

- Single front hub assembly
- Lists Nissan Titan 2007-2011
- Preset, pre-greased and pre-sealed
- Replaces 40202ZR00A, BR930829, 515124
Timken SP500703 is a front hub assembly, and its Amazon listing names the 2007 to 2011 Nissan Titan. Timken is one of the oldest names in tapered roller bearings, and its hub units come preset, pre-greased and pre-sealed, so there is no bearing to pack or preload adjustment to make during installation.
The listing title is useful for matching parts because it spells out what this hub replaces: Nissan numbers 40202ZR00A, 40202ZR00B, 40202ZR40A and 40202ZR40B, plus aftermarket numbers BR930829, 515124 and H515125. Timken calls it an OE-grade replacement. If you can read a number off the hub on your truck, or from a parts receipt, you can compare it with that list before ordering. It ships as a single unit, so you choose whether to replace one side or both.
This hub suits a first-generation Titan owner with a front-end growl or a hub that has started to show play on a lift. The listing does not split 2WD and 4WD models, and Nissan used different hubs for some Titan builds, so check the fitment chart carefully. Confirm your year, drivetrain and cab in Amazon’s fit checker before you buy, and torque the axle nut to Nissan’s specification.
View Timken SP500703 on Amazon
Which Listing Matches Your Pickup
Here is how the best wheel bearings for trucks in this guide line up by model. Confirm the details on each listing.
| Truck named on the listing | Example listing | What you get | Worth noting |
|---|---|---|---|
| F-150 2015-2017, 4WD only | Detroit Axle 4WD pair | Two front hubs | Sensor-wire ABS, 6 lugs |
| F-250 / F-350 Super Duty 2017-2022, 4WD | Detroit Axle 4WD pair | Two front hubs | F-350 listed for SRW only |
| Ram 1500 2012-2018, 1500 Classic 2019-2022 | MOOG front hub | One front hub | 2019-up new-body 1500 not listed |
| Ram 2500 2014-2018, Ram 3500 2013-2018 | MOOG 515162 | One front hub | Heavy-duty 2500 and 3500 trucks |
| Tundra 2007-2021, Sequoia 2008-2022 | TRQ front pair | Driver and passenger hubs | Check 2WD or 4WD fit |
| Titan 2007-2011 | Timken SP500703 | One front hub | Lists the OE numbers it replaces |
On a high-mileage 4×4, both front hubs have seen the same salt and potholes. If you buy a single hub, plan for the other side too, even if only one is loud today.

Road Salt, Rusted Knuckles and Grand Rapids Winters
West Michigan winters are tough on truck hubs. Brine creeps past worn seals, and freeze-thaw potholes hammer the front end all spring. The Car Care Council suggests having steering and suspension checked at least once a year, usually with an alignment, and it lists potholes and vehicle type among the factors that speed up wear.
Salt also makes the repair harder. Rust builds up in the knuckle bore and can lock the old hub in place, so clean the bore to bare metal before the new hub goes in or it may not seat square.

Even the best wheel bearings for trucks wear out eventually, and how long they go depends on load, tire size and how the truck is driven. Our article on how long wheel bearings typically last covers the signs that a hub is near the end.
Installing a Truck Hub and When to Hand It Over
A front hub holds the wheel to the truck, so treat this as safety work. Support the truck on stands rated for its weight, unplug the ABS sensor before you pull the hub, and torque the axle nut and hub bolts to the figures in the service manual. Guessing at axle-nut torque is how a new bearing fails early.

Some rear axles and older trucks still use pressed bearings, and our review of wheel bearing press kits for home garages covers those jobs. Have the alignment checked if you also replaced steering parts.
Picking among the best wheel bearings for trucks is the easy part, and a hub rusted into the knuckle is not. We can handle it. Our shop does wheel bearing replacement in Grand Rapids on foreign and domestic trucks, and our suspension repair service covers the joints and links around the hub.
More Buying Guides
Frequently Asked Questions
Can I put a 2WD hub on a 4WD truck?
Usually not. A 4WD front hub has a splined center that the axle shaft passes through, and a 2WD hub is built without it. Buy the hub listed for your drivetrain and confirm it in Amazon’s fit checker.
Should I replace both front wheel bearings on my truck at once?
On a high-mileage truck it often makes sense, since both sides have seen the same miles and weather. Pairs such as the Detroit Axle and TRQ sets make that easy.
What is the best wheel hub assembly for lifted trucks?
Pick the hub listed for your stock truck from a maker that states its fitment. A lift does not change the hub, but larger tires and wheels with more offset add load, so check the front end for play more often.
Do I need an alignment after replacing a truck wheel bearing?
A bolt-on hub does not change toe or camber, but an alignment check is wise if you removed the knuckle or replaced steering parts.
Hearing a growl from the front of your pickup that gets louder on the highway? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a wheel bearing check through our contact page.
Working the same hours we are? Park the truck in our after-hours drop-off at 456 Carrier St NE, Grand Rapids, with a note on which side is noisy.
