456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Open Pan, Closed Jug or Rolling Cart: The Best Oil Drain Pan for Your Garage

best oil drain pan: peaceful road through lush forest at sunrise near Zlatoust

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

Pulling a drain plug takes seconds, but the oil that follows has to land somewhere and reach a recycling drop-off without a puddle on the driveway. The best oil drain pan for you holds your whole sump with room to spare, fits under the car and pours cleanly.

Below we cover open pans against closed containers and sizing, then review six pans. If you are still deciding whether to drain from below at all, our comparison of topside fluid extractors for oil changes covers the suction route.

Quick answer

Which drain pan should a home mechanic buy?

For most cars and small SUVs, a closed 15 to 16 quart container such as the FloTool 42003MI or Funnel King 32964 is the easiest choice, because you drain, cap and carry it to recycling in one piece. Trucks need about 20 quarts or more, and low cars need a pan under about 5 inches tall.

Our Quick Picks

Three quick picks: a closed container for most cars, a lower closed pan for tight clearance and a rolling cart for a home shop. All six are reviewed below.

FloTool 42003MI product photo
Everyday car

FloTool 42003MI

Closed · 16 quarts · Polyethylene

A long-running closed container that drains, seals and stores in one piece.

SuitsCars and small SUVs on a driveway
View on Amazon →
Funnel King 32964 product photo
Low and closed

Funnel King 32964

Closed · 15 quarts · 5.5 in tall

A wide, flat closed pan that slides under lower vehicles and still seals.

SuitsLower cars where tall jugs will not fit
View on Amazon →
VEVOR 15-Gallon Rolling Drain Pan product photo
Home shop

VEVOR 15-Gallon Rolling Drain Pan

Rolling · 15 gal · 12V pump

A low steel cart that holds oil from several vehicles and pumps it out.

SuitsGarages that service several vehicles
View on Amazon →

Open Pan or Closed Container?

An open pan is a wide tub you pour from into a separate jug. A closed container has a sealed body, a drain area on top and capped spouts, so one unit catches the oil and carries it away.

  • Open pans give the stream a big target and clean out easily, but need a second container for the drop-off.
  • Closed containers skip that transfer and can store oil until you recycle it, though the smaller opening can splash.
  • Rolling carts are closed tanks on wheels, sized for several vehicles in a busy home shop.

Forum owners split on this. Some drain into a wide pan and pour into a sealed jug, while others use a closed container and crack the plug open slowly. Either way, the best oil drain pan is the one that suits your car and your routine.

Sizing the Pan to Your Engine and Driveway

Start with the oil capacity in your owner’s manual, then add the filter and some headroom. A four-cylinder that takes about five quarts is comfortable with a 10 to 16 quart pan. A V8 truck or diesel holding 8 to 15 quarts calls for 20 quarts or more, because a nearly full pan sloshes when you slide it out.

  • Height: measure the gap under the drain plug. Low-profile pans sit around 5 inches tall or less.
  • Caps: a tethered cap with a gasket keeps a container from weeping in storage.
  • Material: polyethylene is light and rust-free, while galvanized steel shrugs off hot oil but has no lid.
  • Handles: fifteen quarts of oil weighs close to 30 pounds, so a good grip matters.

Getting under the car safely matters as much as the pan itself. Our guide to car ramps for DIY oil changes and our roundup of jack stands for a home garage cover the lifting side.

Best Oil Drain Pan Picks, Reviewed One by One

These six cover closed, low-profile, metal, truck-size and rolling designs. Details come from each Amazon listing, so check capacity and dimensions against your car before you order.

1. FloTool 42003MI: 16-Quart Closed Drain Container That Stores Upright or Flat

FloTool 42003MI product photo
Key features
  • 16-quart closed drain container
  • Closed body for catching and carrying
  • Stores upright or flat without leaking
  • Sized for most car and small SUV oil changes

The FloTool 42003MI is a 16-quart closed drain container, the style many DIYers picture when they think of an oil change jug. Instead of an open tub, a closed container of this kind catches the stream on top and funnels it into a sealed body that you cap once the oil has stopped dripping. The Amazon listing’s main point is that it stores upright or flat without leaking, and its photos show the layout.

That storage claim is what makes this type useful. You drain the engine, set the old filter on the well to empty, cap the container and slide it onto a shelf until you are ready for the recycling drop-off. Sixteen quarts gives a typical four or five quart car plenty of headroom, so the oil stays well clear of the openings when you pull the container out from under the car.

As with any closed container, the opening is smaller than a wide open pan, so loosen the plug gradually and position the well a little to the side of the plug to allow for the arc of the stream. The listing on Amazon carries few details, so check the dimensions shown there against the space under your car. Trucks with very large sumps will want a bigger jug.

View FloTool 42003MI on Amazon

2. WirthCo Funnel King 32964: 15-Quart Closed Drain Pan with a 5.5-Inch Low Profile

Funnel King 32964 product photo
Key features
  • Holds up to 15 quarts of used fluid
  • Closed top for carrying to recycling
  • 25 x 18 x 5.5 inch low footprint
  • Heavy-duty polyethylene, made in USA

The WirthCo Funnel King 32964 is a closed drain pan built to be wide and flat rather than tall. The listing gives its size as 25 by 18 by 5.5 inches, with room for up to 15 quarts of used oil, coolant or other waste fluid. That shape lets it slip under vehicles and equipment where a taller drain container would hit the body or a crossmember.

WirthCo molds it from heavy-duty polyethylene, and the listing describes it as made in the USA for repeated use in a garage, shop or driveway. The closed square body is meant to hold the oil securely on the walk from the car to a recycling container, which is the step where open pans tend to spill. The wide top surface also gives a hot stream a large area to land on.

This pan suits a sedan, hatchback or sports car that sits too low for a deep jug, and it also works under lawn tractors and small engines. Fifteen quarts is enough for most passenger car oil changes with room for the filter. Because it is wide, a full pan takes two hands to carry level, so plan the route to your storage spot or collection jug before you start draining.

View Funnel King 32964 on Amazon

quiet rural road surrounded by lush greenery under a clear blue sky

3. CHAPIN 78005: 12-Quart Low-Profile Oil Drain Pan with a Splash-Free Target Area

CHAPIN 78005 product photo
Key features
  • 12-quart capacity
  • Low profile under 5 inches
  • Large splash-free target area
  • Made in USA from recycled polymer

The CHAPIN 78005 is a 12-quart drain pan with a low profile the listing puts at under 5 inches. Chapin is better known for sprayers, and this pan is aimed at the same garage and yard owners, with ATVs, tractors, lawn mowers and motorcycles named on the listing alongside cars. The large target area is designed to catch oil, coolant and additives without splashing over the sides.

Molded-in carry handles help with lifting, tipping and storing it, which matters once the pan is holding several quarts of warm oil. The listing says it is made in the USA from 100 percent recycled polymer, with a one-year limited warranty from Chapin and US-based customer support. Twelve quarts covers one typical car oil change with room left for the filter to drain.

This is a good fit if you service a mix of small engines and a low car, since the shallow body fits where taller containers cannot. It has a wide open target, so plan to pour the oil into a sealed jug for the trip to a recycling center rather than carrying the pan itself. Large trucks with big sumps need a deeper, higher-capacity pan.

View CHAPIN 78005 on Amazon

4. Performance Tool W54280: 3.5-Gallon Galvanized Steel Oil Drain Pan with Rolled Edges

Performance Tool W54280 product photo
Key features
  • 3.5-gallon capacity
  • Galvanized steel with zinc finish
  • 16 inch diameter, 4 inches high
  • Rolled edges and anti-splash ridges

The Performance Tool W54280 is a round, open drain pan made from galvanized steel, for buyers who would rather have metal than plastic under the car. The listing gives a 3.5-gallon capacity, a 16 inch diameter and a height of 4 inches, with rolled edges for a safer grip and ridges in the bottom that the listing says help limit splashing.

Its bright zinc finish is there to resist corrosion, which helps in a damp garage or a shop where the pan gets rinsed out often. Steel also stands up well to hot oil straight from a warm engine and to being dragged across a concrete floor, where thin plastic can crack over time. The listing notes it works for coolant flushes and catching spills as well as oil changes.

Because it is open, there is no cap and no spout, so you need a separate sealed container for the used oil once draining is done. Pouring from a round pan takes a steady hand and a wide funnel. At 4 inches tall it fits under many cars, and 3.5 gallons, about 14 quarts, covers most passenger car oil changes with room for the filter.

View Performance Tool W54280 on Amazon

collection of golden tools arranged in a flat lay on a black surface

5. PAK Premium 23 Quart: Large Closed Oil Drain Pan with Dual Drain Holes and Angled Pour Neck

PAK Premium 23 Quart product photo
Key features
  • 23-quart capacity
  • Two drain holes for faster flow
  • Angled neck with tethered cap
  • High-density polyethylene, made in USA

The PAK Premium 23 Quart is a large closed drain pan for engines that hold more oil than a typical car. According to the listing, it has enough volume for most vehicles, and the extra room matters on V8 trucks and diesels whose sumps can take well over ten quarts. A bigger reserve also means the oil sits lower in the body, so it sloshes less when you drag the pan out.

The listing describes two drain holes placed to increase flow into the container, which helps when a thick, cold oil is slow to run through a single opening. An angled neck with a tethered cap is there for controlled pouring into a collection tank, and the cap stays attached so it does not get lost under the car. PAK makes it in the USA from high-density polyethylene.

This pan suits owners who change oil on a pickup, a full-size SUV or two cars before a trip to the recycling center. Check its height against the gap under your drain plug, because a tall truck has room to spare but a low car may not. A full 23-quart load is heavy, so have a clear path and use the handle with both hands.

View PAK Premium 23 Quart on Amazon

6. VEVOR 15-Gallon Rolling Oil Drain Pan: Low-Profile Steel Cart with 12V Electric Pump

VEVOR 15-Gallon Rolling Drain Pan product photo
Key features
  • 15-gallon steel tank
  • 12V pump with 7.2 ft hose
  • Low profile with four wheels
  • Mesh filter and folding T-handle

The VEVOR 15-Gallon Rolling Oil Drain Pan is a different class of tool from a plastic jug. It is a low-profile carbon steel tank on four wheels, two swivel casters with brakes and two fixed wheels, with a folding T-handle for steering. The listing says the low body fits under low cars, motorcycles and ATVs without lifting them.

Its main feature is a 12V pump with a 7.2 foot hose that moves the collected oil into a storage tank or drum, so you never lift or pour a full pan. The 15-gallon capacity holds oil from several vehicles, and a large mesh filter screens debris before it reaches the pump. VEVOR describes the reinforced steel body as built to handle heat and heavy use.

This suits a home mechanic who maintains a few family cars, a farm truck and equipment, or anyone who empties oil into a bulk tank for the recycler. For one car twice a year it is more cart than you need, and it takes up floor space when parked. Check the listing for the pump’s power connection and the hose length against your setup before you buy.

View VEVOR 15-Gallon Rolling Drain Pan on Amazon

How the Six Pans Compare

Use the table to shortlist by style and capacity, then check the height against the space under your drain plug.

PanStyleCapacity (listing)Good fit
FloTool 42003MIClosed container16 quartsCars and small SUVs
Funnel King 32964Closed, low profile15 quartsLower cars that still want a lid
CHAPIN 78005Low-profile pan12 quartsMowers, ATVs, motorcycles and cars
Performance Tool W54280Open galvanized steel3.5 gallonsHot oil, coolant and rough floors
PAK Premium 23 QuartClosed container23 quartsV8 trucks and diesels
VEVOR 15-GallonRolling cart with pump15 gallonsHome shops servicing several vehicles
Six oil drain pans compared by style, listed capacity and the kind of job each one suits

For a typical car, the best oil drain pan is usually a closed 15 or 16 quart container. Step up to 23 quarts for a truck, go low-profile for a low car, and save the rolling cart for a garage that sees several oil changes a month.

scenic autumn forest road covered in leaves

Winter Oil Changes and Recycling in West Michigan

Plenty of Grand Rapids drivers change oil in an unheated garage between November and March. Cold oil drains slowly, so run the engine for a few minutes first and give it extra time to drip. A rigid pan slides over a cold, gritty floor better than a flimsy one.

Winter is also when the right viscosity matters most. Our guide to the best motor oil for cold weather starts explains the W number, and our oil filter wrench guide for stuck and tight filters handles the messy filter step.

scenic close-up shot of an empty asphalt road with yellow lines curving through a forested area

Used oil never goes in the trash or down a drain. The American Petroleum Institute’s used motor oil collection and recycling site explains that oil taken to a collection center can be burned for heat or re-refined into base oil. Keep it sealed, keep coolant out of it, and drain the old filter into the pan before the drop-off.

When the Job Belongs on a Lift

A stripped drain plug, a weeping oil pan gasket, metal flakes or milky oil all need a proper look before the next fill. If the oil pressure light came on before the change, read our guide to an oil pressure light that comes on while driving first.

Unsure how long you can stretch the interval? Our article on how often to change oil on a modern engine walks through the manual’s schedule. When you would rather skip the crawling, our oil change service in Creston drains, refills and checks the plug, filter and leaks with the car up on a lift.

curved roads winding through Karnataka's green hills on a cloudy day

Frequently Asked Questions

What size oil drain pan do I need?

Pick a pan that holds at least twice your engine’s oil capacity. Most cars take 4 to 6 quarts, so a 10 to 16 quart pan leaves room for the filter and avoids sloshing. Trucks and diesels with larger sumps are better served by 20 quarts or more.

Is a metal or plastic drain pan better?

Each has a place. Plastic closed containers are light, rust-free and let you cap the oil for the trip to recycling. A galvanized steel pan handles hot fluid and rough floors well, but it is open, so you need a separate sealed jug for disposal.

Can I store used oil in a closed drain container?

Yes, that is what the caps are for. Keep the container upright or flat as the listing allows, away from heat, and check the cap gaskets now and then. Take it to a collection center before the next change so it never overfills.

Can I use the same pan for coolant?

You can, but clean it well between jobs and never mix the two fluids. Recycling centers usually refuse oil contaminated with antifreeze. Many people keep a separate, clearly marked pan just for coolant.

Found a leak, a stripped plug or oil that looks wrong while you had the pan underneath? Give 456 AutoFix a call at 616-279-3832 on a weekday between 8am and 5pm, or pick a time through our contact page.

If your workday runs into our hours, the after-hours drop-off at our 456 Carrier St NE shop in Grand Rapids lets you leave the car whenever suits you.