As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A Gladiator that pulls after every pothole, or shows play when you rock the front tire at twelve and six o’clock, usually has worn joints in the steering knuckle. Shopping for the best ball joints for Gladiator trucks is simpler than it is for most pickups, because every 2020 and later JT rides on the same style of front axle. The real choices are position, quantity and how hard the truck works.
We sorted six listings by what they replace: a lower pair, an upper pair, a one-side kit or a full heavy duty swap. If you are not yet sure the joints are at fault, our guide to bad ball joint symptoms covers the clunks, wander and tire wear to look for first.
Quick answer
Which ball joints suit a Jeep Gladiator JT?
For a stock 2020-2023 Gladiator, the TRQ lower and upper pairs replace the factory joints position by position. If you run bigger tires or heavy armor, the greasable Yukon or Dana Spicer one-side kits are the sturdier route. Confirm year, trim and axle on Amazon before you order.
Our Quick Picks
Three listings that cover the most common Gladiator front end jobs. Check your model year and trim on Amazon before ordering.

Yukon One-Side Ball Joint Kit
A chromoly-stud kit that rebuilds one knuckle at a time.

Dana Spicer Ball Joint Kit
A Spicer kit from the company behind the Dana 44 AdvanTEK axle.

TRQ Front Lower Ball Joint Set
Both lower joints in one box for a stock-height Gladiator.
One Axle Design, Four Joints to Think About
The Gladiator uses a solid front axle with an upper and a lower ball joint in each steering knuckle, so a full refresh means four joints. Dana’s Spicer catalog lists the 2020 and later JT with the Dana 44 AdvanTEK front axle, known as the Model 210, and shows one service kit for either side. That is the same axle model it lists for some Wrangler JL trims, which is why so many kits name both trucks.
Shared fitment is not a blanket rule, though. Some listings stop at 2021 or 2023, so read the year range and run your truck through Amazon’s fit checker.
- Lower joints: they carry more load and are often the first to show play.
- Upper joints: they wear more slowly on a stock truck but suffer with a lift or wide tires.
- One-side kits: an upper and a lower for one knuckle, so a full axle needs two kits.
Stock Style or Heavy Duty?
Factory JT joints are sealed. Spicer describes the original equipment design as plastic-on-plastic and not serviceable, and says its own performance kit moves to metal-on-metal construction with a grease fitting. Sealed joints need no attention until they wear out, while greasable ones let you push water and grit out after a wet season.
A truck on stock tires that mostly sees pavement is well served by OE-style replacements. Heavy duty kits make more sense once you add a lift, 35 inch tires, a steel bumper or a winch, because every extra pound and every inch of tire leverage loads the joints harder.
Best Ball Joints for Gladiator: The Listings by Position
The first two picks are the kits we would point a lifted or hard-used truck toward, the next three are position-by-position replacements, and the last is a full redesign for trail rigs. Each listing names its own years and contents, so use this as a shortlist and confirm the exact fit for your truck.
1. Yukon Ball Joint Kit: Upper and Lower Joints for One Side of a Wrangler JL or Gladiator JT

- One upper and one lower joint
- Forged 4140 chromoly ball stud
- Rolled threads and sealed boots
- Listing names Wrangler JL and Gladiator JT
Yukon Gear and Axle is mostly known for differential parts, and this kit carries that axle focus over to the steering knuckle. The listing names the Wrangler JL and Gladiator JT and includes one upper joint, one lower joint and the small parts needed to fit them, so a single box rebuilds one side of the front axle. Buy two if both knuckles have play.
The construction details are what set it apart from a basic replacement. Yukon lists a CNC-machined housing forged from SAE 1045 carbon steel, a hot-forged 4140 chromoly ball stud that is induction heat treated, and threads that are rolled rather than cut, which the maker says makes them stronger. Sealing comes from a neoprene-enhanced rubber boot plus an internal pancake seal, a sensible choice for trucks that see slush, mud and creek crossings. The kit carries a lifetime warranty against manufacturing defects.
Yukon also warns that the steering may show some memory steer for the first 300 to 500 miles while the joints break in, so do not judge the feel on the first drive. This is a better fit for lifted trucks, heavier bumpers and larger tires than for a stock commuter, where a simpler joint may be all you need.
View Yukon One-Side Ball Joint Kit on Amazon
2. Dana Spicer Ball Joint Kit: Upper and Lower Joints for Wrangler JL and Gladiator JT

- Made by the maker of the JT front axle
- Upper and lower joints in one kit
- Listing names Wrangler JL and Gladiator JT
- Sold through a third-party seller
Dana builds the Dana 44 AdvanTEK front axle under the Gladiator, and Spicer is its aftermarket parts brand, so this kit comes from the same company as the axle itself. The Amazon listing is sold by a third-party seller and gives little beyond its title, which names upper and lower ball joints for the Wrangler JL and Gladiator JT. That makes it worth reading the photos and the seller’s notes before you add it to the cart.
Spicer’s own catalog page describes its performance kit for these trucks in more detail. It lists one part number for the left or right side, with one upper joint, one lower joint, nuts and cotter pins in the box. The maker says its joints use a metal-on-metal design with a grease fitting, replacing the sealed factory joints, and points to bigger tires and added weight as reasons the original parts wear faster.
Because the listing does not show that part number or the quantity, compare the photos with Spicer’s description and confirm whether you are buying one side or a full set. A Gladiator with heavier accessories that will see regular greasing suits it well, and a stock truck may not need the extra servicing.
View Dana Spicer Ball Joint Kit on Amazon

3. TRQ Front Lower Ball Joint Set: Driver and Passenger Side for 2020-2023 Gladiator

- Two front lower ball joints
- Listing names 2020-2023 Gladiator
- Cross-references K500464 and 68388819AA
- Limited lifetime warranty
Lower joints are usually the first to loosen on a JT, and this TRQ set covers both of them in one order. The listing names the 2018-2023 Wrangler and 2020-2023 Gladiator and includes one driver side and one passenger side front lower joint. If your truck is a 2024 or newer, look elsewhere or confirm fit carefully before buying.
TRQ prints its reference numbers on the listing, including 68388819AA, 68531030AB, K500464 and MS25575, which makes it easy to compare against a parts quote or another brand’s catalog. The joints are described as pre-assembled direct replacements for the original equipment, so no modification should be needed to fit them. TRQ also publishes a large library of installation videos, which can help if you have pressed joints before but not on this axle. Coverage is a limited lifetime warranty against defects in materials and workmanship.
This is a stock-style part rather than a heavy duty upgrade, so it suits a truck on factory or mild tire sizes that mostly sees pavement. The listing does not state whether the joints are greasable, so check the photos if that matters. Pair it with the upper set below if both positions are worn.
View TRQ Front Lower Ball Joint Set on Amazon
4. TRQ Front Upper Ball Joint Set: Driver and Passenger Side for 2020-2023 Gladiator

- Two front upper ball joints
- Listing names 2020-2023 Gladiator
- Cross-references K500433 and 2601955
- Limited lifetime warranty
The matching upper set from TRQ fills in the other half of the knuckle. It includes a driver side and a passenger side front upper joint, and the title names the 2020-2023 Gladiator along with the 2018-2023 Wrangler. Ordered with the lower set above, it gives you all four positions from the same brand.
The reference numbers listed include 68388819AA, 2601955, K500433, MS25574 and X22BJ0478, so you can line it up against the MOOG and dealer numbers you may already have. Like the lower set, it is sold as a pre-assembled direct replacement that should bolt into the factory locations without changes, and it carries the same limited lifetime warranty against defects. TRQ asks buyers to use Amazon’s confirmed fit tool and check its compatibility chart before ordering.
Upper joints often last longer than lowers on a stock truck, so do not replace them automatically. Check for play with the wheel off the ground and look for split or greasy boots first. If the uppers are sound, the lower set alone may be the whole job. Trucks with tall lifts or very large tires may be better served by a heavier kit.
View TRQ Front Upper Ball Joint Set on Amazon

5. Metrix Front Ball Joint Kit: 2 PC K500433 Uppers for 2020-2026 Gladiator

- Two K500433 front ball joints
- Listing names 2020-2026 Gladiator
- Pre-greased steel construction
- 3 year / 36,000 mile limited warranty
Metrix lists this two-piece kit for the 2018-2026 Wrangler and the 2020-2026 Gladiator, which is a wider year range than most listings here and useful if your truck is newer than 2023. The box holds two front ball joints under the K500433 number, the same reference used for the JT upper position by MOOG and in the TRQ cross-references, so expect two uppers rather than a mixed set.
The joints are pre-greased and made of steel, and Metrix says they are built to exceed original equipment specifications in factories certified to IATF 16949 and ISO 9001, two common quality management standards in auto parts manufacturing. The title also notes they are made in Europe. Coverage is a three year or 36,000 mile limited warranty from the date of installation, which is clearer than some listings about how long support lasts.
This kit only covers the upper joints, so a truck with loose lowers will need a separate lower pair. Whether the joints carry a grease fitting is not stated beyond pre-greasing. Confirm your model year and trim with Amazon’s fit checker, since the long year range makes it easy to assume a fit.
View Metrix K500433 Ball Joint Kit on Amazon
6. American Iron Offroad AI-1101: Ball Joint Delete System for Jeep JL and JT

- Spherical bearings replace ball joints
- 4140 chromoly hardware with zinc coating
- Rebuildable and adjustable
- Listing names JL and JT, 2018-2024
This one is a different approach to the same job. Instead of replacing worn ball joints like for like, the AI-1101 removes them and fits spherical bearing assemblies in their place, which American Iron Offroad calls a ball joint delete system. The listing names the Jeep JL and JT from 2018 to 2024, and it suits owners who want the heaviest option rather than a stock repair.
The maker lists 4140 heat-treated chromoly hardware with a zinc coating, oversized 3/4 inch PTFE-lined spherical bearings, and double-ended studs that let you adjust steering firmness. A high-clearance lower cup is meant to make room for aftermarket axle shafts and larger tires. The design is greased and rebuildable, so worn bearings can be replaced later without starting over. The upper also has a shoulder intended to stop the knuckle from dropping off completely if a shaft fails, and the warranty is two years or 30,000 miles.
The listing claims it eliminates death wobble, but that shake has several possible causes, so treat the claim with care. Adjustable steering also means more setup than a sealed joint, and it is overkill for a Gladiator that rarely leaves pavement.
View American Iron Offroad AI-1101 on Amazon
Gladiator Listing Map
This table reflects what each listing states, not a promise that every trim in that range will take the part.
| Listing | Gladiator years named | What is in the box | Suits |
|---|---|---|---|
| Yukon one-side kit | JT (no years in title) | 1 upper, 1 lower | Lifted or heavy trucks |
| Dana Spicer kit | JT (no years in title) | Upper and lower, check quantity | Greasable OE-maker upgrade |
| TRQ lower set | 2020-2023 | 2 lowers | Stock trucks with lower play |
| TRQ upper set | 2020-2023 | 2 uppers | Stock trucks with upper play |
| Metrix K500433 kit | 2020-2026 | 2 uppers | Newer trucks needing uppers |
| American Iron Offroad AI-1101 | JT (2018-2024 in title) | Delete system, both sides | Dedicated trail builds |

Salt, Big Tires and Wobble in West Michigan
Our winters are hard on front ends. Brine sprayed on the roads works into any split boot, and a sealed joint that takes on water cannot be flushed, so it wears from the inside.
Many Gladiator owners first notice trouble as a shake after a bump at highway speed, often called death wobble. Worn ball joints can play a part, but so can a loose track bar, worn tie rod ends, a tired steering stabilizer or out-of-balance tires. Our guide to tie rod ends for Jeep models covers that side of the steering, and worn dampers make every impact harsher, which our roundup of shocks and struts for daily drivers explains.

If your truck shares the garage with a Wrangler, our guide to ball joints for the Wrangler JL covers kits not repeated here. For other makes and car-based SUVs, the wider ball joint roundup is the better starting point. Picking the best ball joints for Gladiator owners still comes down to how the truck is built and driven, so be honest about tire size and load.
Doing the Swap Yourself or Booking It
JT joints press into the knuckle, so the job means pulling the hub, separating tapered studs and using a C-frame press with the correct adapters. Our look at ball joint press kits explains what to look for in the tool. Tighten every nut to the service manual figure and use new cotter pins.

Even the best ball joints for Gladiator axles will not drive straight if a joint is pressed in crooked, and the truck needs an alignment once the knuckles go back together. If you would prefer us to handle it, our suspension repair service in Grand Rapids includes checking the joints, track bar and tie rods together. Steering and suspension is one of the areas where Hendrick Hoffman, who runs our shop, holds both ASE and State of Michigan certification.
More Buying Guides
Frequently Asked Questions
Do the Gladiator and Wrangler JL share ball joints?
Often, yes. Spicer lists one kit for the JT’s Dana 44 AdvanTEK axle and the JL, and many aftermarket listings name both trucks. Year ranges still differ between brands, so check the listing and Amazon’s fit checker for your exact truck.
Should I replace the uppers and lowers together?
Not always. If only the lowers show play, a lower pair is enough. On a lifted truck or one with high miles, doing all four while the knuckles are off saves pulling the front end apart twice.
Will heavy duty ball joints cure death wobble?
Only if the joints are the cause. The shake can also come from the track bar, tie rod ends, steering stabilizer or tire balance, so have the whole front end checked before you spend money on parts.
Is an alignment needed after a ball joint job?
Yes. Pulling and refitting the knuckles can change camber and toe, so an alignment afterwards keeps the steering wheel straight and protects your tires.
Is your JT shaking, wandering or knocking over rough pavement? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or book a front end inspection online.
Can’t get away during shop hours? Pull the Gladiator into 456 Carrier St NE, Grand Rapids, MI 49505 after closing time and hand it over through the after-hours drop-off.
