456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Third Gen to 2020 Trucks: The Best Ball Joints for Toyota 4Runner Owners

best ball joints for toyota 4runner: glimpse into the detailed crafting process in a wooden skateboard workshop

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A 4Runner that knocks when you back out of a sloped driveway, or one whose steering feels vague on a rutted road, is often asking for new front ball joints. Choosing the best ball joints for Toyota 4Runner front ends comes down to the generation first. A 1996-2002 third gen uses side-specific lowers that bolt to the knuckle, while 2003 and later trucks share one lower and one upper design across both sides.

This guide splits six Amazon listings by generation and position and names the part numbers each one prints. Not sure they are worn? Our article on bad ball joint symptoms covers the clunks, uneven tire wear and play you can feel by hand.

Quick answer

Which ball joints suit a 4Runner?

For 2003-2020 trucks, start with the MOOG K500417 lower and K500018 upper, or the TRQ four-piece set. Third gen 1996-2002 owners can pick the Genuine Toyota lower pair, MOOG K90262 and K90263, or a TRQ lower pair. Confirm year, trim and suspension type on Amazon before you order.

Our Quick Picks

Three listings that cover the most common 4Runner front end jobs, from third gen lowers to full sets for later trucks. Check your year and trim on Amazon before ordering.

MOOG K500417 product photo
2003+ lower

MOOG K500417

Front lower, single joint

A MOOG lower joint listed for fourth and fifth gen 4Runners.

Suits2003-2020 owners replacing a worn lower joint
View on Amazon →
Genuine Toyota Lower Pair product photo
3rd gen OEM

Genuine Toyota Lower Pair

Front lower pair, genuine Toyota

The original Toyota lowers that many third gen owners ask for.

Suits1996-2002 4Runners where you want factory parts
View on Amazon →
TRQ Four-Piece Set product photo
Full set

TRQ Four-Piece Set

4 joints, upper and lower

Both uppers and both lowers for 2003 and later trucks in one order.

SuitsHigh-mileage 4Runners with an unknown front end history
View on Amazon →

Know Your 4Runner Generation Before You Shop

Toyota has changed the 4Runner front end several times. The third gen, built for 1996 through 2002, moved to a coil-sprung double wishbone layout with a lower joint that bolts to the steering knuckle and is sold as a left or right part.

From 2003 the fourth gen shared its front suspension with the Lexus GX470 and later the FJ Cruiser, and the fifth gen that followed in 2010 kept a closely related front end. That is why one MOOG lower listing covers 2003 through 2020 trucks. None of the listings below claim to fit the newer sixth gen.

Write down three things before you search: model year, whether the truck has KDSS (Toyota’s Kinetic Dynamic Suspension System, fitted to some 2003 and later trims), and whether it runs a lift. Then read the fitment notes under each listing, since some sellers exclude KDSS trucks.

Uppers, Lowers and the OEM Question

On every generation listed here, the lower joint carries the weight of the front of the truck and wears first. Third gen owners often call that lower a non-failsafe design, because the truck’s weight pulls the stud out of the socket rather than pressing it in. A worn one that separates can let the wheel fold under, so third gen owners check them often.

  • Single joints: when only one side shows play.
  • Lower pairs: both sides in one order.
  • Four-piece sets: uppers and lowers for both sides.
  • Genuine Toyota lowers: still sold, and preferred by many third gen owners.

Grease fittings matter on a truck that sees slush and gravel. MOOG explains its ball joint construction, including a sealed boot with a grease-relief valve and a powdered metal bearing that lets new grease flow across the bearing surface.

Best Ball Joints for Toyota 4Runner: Every Pick by Generation

The first three products fit 2003 and later trucks, and the last three are for the 1996-2002 third gen. Each heading names the position and years its listing prints.

1. MOOG K500417: Front Lower Ball Joint for 2003-2020 Toyota 4Runner

MOOG K500417 product photo
Key features
  • Front lower position, single joint
  • Listing names 2003-2009 and 2010-2020 4Runner
  • Also listed for GX470, GX460 and FJ Cruiser
  • Made by DRiV under the MOOG brand

The MOOG K500417 is a front lower ball joint for fourth and fifth generation 4Runners. Its compatibility bullet lists 2003-2009 and 2010-2020 trucks, plus the Lexus GX470, the GX460 and the FJ Cruiser, which share the same basic front suspension. On these SUVs the lower joint connects the lower control arm to the steering knuckle and carries most of the front end load.

The listing describes the joint as a key pivot between suspension parts, built to cope with road stress and help bring back steady steering on a worn front end. MOOG is a long established chassis brand from DRiV, and its K-series numbers are widely used as a cross-reference, so it is easy to compare this part against other brands or a written quote. The listing does not say whether this joint carries a grease fitting, so check the photos and the product description if you plan to grease it at every oil change.

You get one joint in the box, so a job on both sides means ordering two. It is not a match for the 1996-2002 third gen, which uses side-specific lowers, or for the newest sixth gen trucks. Confirm KDSS notes and your exact year on Amazon, and book an alignment once the new joints are in.

View MOOG K500417 on Amazon

2. MOOG K500018: Front Upper Ball Joint for 2003-2019 Toyota 4Runner

MOOG K500018 product photo
Key features
  • Front upper position, single joint
  • Listing title names 2003-2019 4Runner
  • Also listed for Tundra, Sequoia and FJ Cruiser
  • MOOG cross-reference number used by other brands

The MOOG K500018 is the upper partner to the lower joint above. Its title names 2003-2019 4Runners, while the compatibility bullet splits that into 2003-2018 and 2010-2019, along with the GX470, GX460, FJ Cruiser, 2007-2021 Tundra and 2008-2022 Sequoia. Because the bullet and the title read a little differently for the final model years, use the fit checker if your truck is a 2019.

The upper joint sits at the top of the knuckle and sees less load than the lower, so it usually lasts longer. It still wears, and a torn boot or play you can feel with the wheel off the ground is a reason to replace it. The listing describes the same MOOG focus on controlled pivoting and steady steering as the lower joint, and the part number makes it simple to match against other brands’ cross-reference lists.

On some trucks the upper joint is serviced by replacing the whole upper control arm, so look at how yours is fitted before you order a bare joint. Lifted 4Runners with aftermarket upper arms often use a different joint entirely. One joint comes in the box, so order two for both sides.

View MOOG K500018 on Amazon

car driving on roadway with snow and traces against residential houses illuminated by streetlights in night ci

3. TRQ Front Ball Joint Set: Upper and Lower, Both Sides, for 2003-2018 4Runner

TRQ Four-Piece Set product photo
Key features
  • 2 front lower and 2 front upper joints
  • Listed for 2003-2018 4Runner, GX470 and FJ Cruiser
  • Cross-references K500017 and K500018
  • Limited lifetime warranty stated on the listing

This TRQ kit packs four joints in one box: two front lowers and two front uppers. The title covers the 2003-2018 4Runner, the 2003-2009 Lexus GX470 and the 2007-2014 FJ Cruiser. Its reference list includes MOOG K500017 and K500018 along with several Toyota numbers, which helps if you want to compare it against a parts counter quote.

A full set makes sense when you buy a used 4Runner with no service history, or when one joint has failed and the rest have similar mileage. Doing all four at once means the front end comes apart a single time, and the truck only needs one alignment at the end. TRQ describes the parts as pre-assembled direct replacements for the original equipment, and the listing links to the brand’s own installation videos.

The listing states a limited lifetime warranty against defects, but it excludes normal wear, misuse and modification. It does not name 2019 and later trucks or mention KDSS, so check your trim and year carefully in the Amazon garage tool. If only one side shows play and the truck has low miles, a single joint from the picks above is the simpler and cheaper fix.

View TRQ Four-Piece Set on Amazon

4. Genuine Toyota 43330-39585 and 43340-39465: Front Lower Ball Joint Pair for 4Runner

Genuine Toyota Lower Pair product photo
Key features
  • Toyota OEM front lower joints, left and right
  • Part numbers 43330-39585 and 43340-39465
  • Numbers match TRQ's 1996-2002 cross-reference
  • Sold as a two-piece set

This listing pairs two genuine Toyota front lower ball joints, part numbers 43330-39585 and 43340-39465, one for each side. The title names the 4Runner but does not print a year range. Both numbers do appear in the 1996-2002 reference list on TRQ’s third gen lower set, so this is the factory pair for that generation, but confirm it against your VIN with a dealer or the fit checker.

Third gen owners on enthusiast forums often say they would rather run Toyota lowers than any aftermarket option, because these joints hold the front of the truck up and are loaded in a way that pulls the stud outward. Buying the original part takes the guesswork out of fit and finish. The joints bolt to the knuckle, so the install is the same as with any of the aftermarket pairs reviewed here.

The listing gives very little detail beyond the part numbers and the OEM label, so check the seller and the photos before you order. Bolts and nuts may not be included, so check before the truck goes up on stands. These lowers do not fit 2003 and later 4Runners, and you still need an alignment once they are fitted.

View Genuine Toyota Lower Pair on Amazon

serene winter landscape of a rural road flanked by snow-covered trees

5. MOOG K90262: Front Left Lower Ball Joint for 1996-2002 Toyota 4Runner

MOOG K90262 product photo
Key features
  • Front lower, driver side only
  • Listed for 1996-2002 4Runner
  • Also fits 2000-2002 Tundra and 2001-2002 Sequoia
  • Right side partner is the MOOG K90263

The MOOG K90262 is a driver side front lower ball joint for the 1996-2002 4Runner. The same joint is listed for the 2000-2002 Tundra and 2001-2002 Sequoia. Its title gives a long run of replaced numbers, including Toyota’s 43340 series, so you can check it against the old part, a parts receipt or the number stamped on the joint you take off.

Third gen lowers are handed, which means the left and right joints are different parts. If the passenger side is worn, the matching part is the MOOG K90263 right lower, which is listed for the same trucks. Buying one side at a time suits a truck where one lower has play and the other checks out tight, or where one side was replaced recently and has its own receipt.

MOOG is the aftermarket name most often mentioned by third gen owners, and some aftermarket control arm makers ship MOOG joints with their arms. The listing does not say whether this one carries a grease fitting. It will not fit 2003 and later 4Runners, so check your year and the side you need before you add it to the cart, and plan on an alignment afterwards.

View MOOG K90262 on Amazon

6. TRQ Front Lower Ball Joint Set: Driver and Passenger for 1996-2002 4Runner

TRQ Third Gen Lower Pair product photo
Key features
  • 1 driver side and 1 passenger side lower
  • Listed for 1996-2002 4Runner
  • Cross-references K90262 and K90263
  • Limited lifetime warranty stated on the listing

This TRQ set gives you both third gen lower joints in one box, one for the driver side and one for the passenger side. The title lists the 1996-2002 4Runner, 2001-2002 Sequoia and 2000-2002 Tundra. Its reference list includes MOOG K90262 and K90263, Mevotech MK90262 and MK90263, and a long run of Toyota 43330 and 43340 numbers, which makes cross-checking easy.

Buying a matched pair takes the risk out of ordering two handed parts separately and getting the same side twice. It also keeps both sides of the front end at the same age, which helps a high-mileage truck steer evenly. TRQ calls the joints direct replacements for the original parts and points to its library of installation videos for owners doing the job in a driveway.

The warranty on the listing covers defects, not normal wear. Like every third gen lower in this guide, these will not suit 2003 and later trucks, and the listing does not say whether the joints are greasable. Read the fit notes on the listing, plan to replace any rusted hardware while the knuckle is apart, and get the alignment checked when you are done.

View TRQ Third Gen Lower Pair on Amazon

4Runner Fit Chart by Year and Position

The chart pairs each listing with the trucks it names. Use it as a starting point, not a fit guarantee for every trim.

4Runner yearsPositionListings to check
2003-2020 (fourth and fifth gen)Front lower, singleMOOG K500417
2003-2019Front upper, singleMOOG K500018
2003-2018Upper and lower, both sidesTRQ four-piece set
1996-2002 (third gen)Front lower pair, OEMGenuine Toyota 43330-39585 and 43340-39465
1996-2002Front lower, left or rightMOOG K90262 left, K90263 right
1996-2002Front lower pairTRQ lower set
4Runner generations and positions matched to the ball joint listings reviewed in this guide
tranquil winter scene

Salt, Lift Kits and KDSS Trucks

Grand Rapids winters are hard on front joints. Brine finds its way through a split boot, and freeze-thaw potholes hammer the lowers every spring, so a 4Runner driven year round here usually needs joints sooner than a truck kept in a dry climate. Check the boots at every tire rotation.

Lifts change the angle the joints run at, and the uppers feel it most. Many owners with a lift of two inches or more swap to aftermarket upper arms with their own joint, which our guide to upper control arms for the 4Runner covers. Tired shocks also let the front end slam into bumps, and our roundup of shocks and struts for daily drivers explains how to spot worn ones.

craftsman focuses on woodworking in a sunlit workshop

KDSS trucks use hydraulic sway bars that need extra care when the front end is apart, so read any listing note that mentions them. Toyota also lets you run your VIN through its recall and service campaign lookup, which is worth a minute on a used truck before buying parts. For other makes and models, our main guide to the best ball joints for cars and SUVs sorts listings the same way.

Doing the Swap at Home or Booking a Shop

On a third gen, the lower joint bolts to the knuckle, so the main fight is breaking the tapered stud loose from the control arm. Mounting differs on later trucks, so read the install notes for your listing, and have a C-frame press with adapters ready for any joint that is a press fit. Our guide to ball joint press kits covers the tools.

snow-covered forest road with a warning sign and power lines on a wintry day

Even the best ball joints for Toyota 4Runner trucks only last if the castle nuts are torqued to Toyota’s figure, new cotter pins go in and the truck gets an alignment afterwards. If you would rather hand it off, our suspension repair team in Grand Rapids inspects and replaces ball joints Hendrick Hoffman, our owner and head mechanic, is ASE and State of Michigan certified for steering and suspension.

Frequently Asked Questions

Do 2003-2009 and 2010-2020 4Runners take the same lower ball joint?

The MOOG K500417 listing names both ranges, along with the GX470, GX460 and FJ Cruiser. Coverage of the last model years differs slightly between the listing title and its bullet, so run your exact truck through Amazon’s fit checker.

Are third gen 4Runner lower ball joints different on each side?

Yes. MOOG sells the K90262 for the left side and the K90263 for the right, and Toyota uses separate part numbers too. Buy a matched pair or order the correct side for the joint you are replacing.

Is a genuine Toyota lower worth it on a 1996-2002 4Runner?

Many third gen owners prefer the original part for the lowers because of how they are loaded. Quality aftermarket joints from brands like MOOG and TRQ are also widely used, so the choice often comes down to availability and how the truck is driven.

Does a 4Runner need an alignment after new ball joints?

Yes. Separating the knuckle and fitting new joints can move camber and toe, so plan an alignment as soon as the job is done to keep the steering centered and the tires wearing evenly.

Hearing a knock from the front of your 4Runner on every pothole? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or reach us online to book a front end inspection.

Can’t get away during the week? Point the truck toward 456 Carrier St NE, Grand Rapids, MI 49505 in the evening and use our after-hours drop-off.