456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Lifted or Stock Height? The Best Upper Control Arms for 4Runner Trucks

best upper control arms for 4runner: model off-road truck on a sandy beach

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

Lift a 4Runner a couple of inches and the alignment shop may hand back a printout full of red numbers, with caster stuck low and camber out of range. On a high-mileage stock truck the story is different: a dry upper ball joint or a split bushing starts to knock on rough pavement. The best upper control arms for 4Runner owners solve one of those two problems, and the right pick depends on which one you have.

This page narrows our wider guide to trusted control arm brands to Toyota’s midsize SUV, with six listings covering the 3rd, 4th and 5th generation trucks.

Quick answer

Which upper control arms suit a 4Runner?

For a lifted 2003 or newer 4Runner, an aftermarket arm with extra caster, such as the ICON 58451DJ or the Dobinsons UCA59-002K, lets the alignment come back into spec. On a stock truck, an OE-style arm like the MOOG RK620064 is the simpler repair. Check generation, side and options, then book an alignment.

Our Quick Picks

Three quick picks: a lift arm for 2003 and newer trucks, an OE-style replacement for stock height and a pair for the 3rd gen. All six listings are reviewed below.

ICON 58451DJ product photo
Lift pick

ICON 58451DJ

Delta Joint · 2003-up 4Runner

Tubular lift arm built around ICON's own pivot joint.

SuitsLifted 4th and 5th gen trucks
View on Amazon →
MOOG RK620064 product photo
Stock-height pick

MOOG RK620064

Front left upper · 2003-2024

An OE-style arm with the ball joint already fitted.

SuitsUnlifted 4th and 5th gen trucks
View on Amazon →
HHCM K640609/K640610 Pair product photo
3rd gen pick

HHCM K640609/K640610 Pair

Pair · 1996-2002 4Runner

Both front upper arms for the older body style.

SuitsWorn 3rd gen front ends
View on Amazon →

Why a Lift Changes the Upper Arm’s Job

The 4Runner’s front end uses two A-shaped arms per side. The lower arm carries the spring and shock, while the shorter upper arm locates the top of the knuckle through a ball joint. Together they set caster and camber, which decide how straight the truck tracks and how evenly the tires wear.

A leveling kit or coilover lift drops the lower arm further from the frame. The factory upper arm then sits at a steeper angle, which pulls caster down and tips camber out. Dobinsons explains on its arms and components page that once an independent front end goes up by more than about 2 inches, a correct wheel alignment is often no longer possible with stock arms.

A steep upper arm can also push the ball joint toward its travel limit. Aftermarket arms build in extra caster and give the joint more room. At factory height none of this applies, and an OE-style arm makes more sense.

Ball Joint, Uniball or Delta Joint

The outer pivot is where upper arms differ most. Each design trades some daily-driving comfort against off-road travel and upkeep.

  • Ball joint: a sealed or greaseable joint like the factory part, quiet on the road and the least work to keep up.
  • Uniball: a spherical bearing that allows a wider swing for more wheel travel, but it needs regular checks and is more exposed to grit.
  • ICON Delta Joint: ICON’s own pivot design, offered as an alternative to both a standard ball joint and a uniball on its lift arms.

For mostly highway miles, a ball joint arm is the easier one to live with. Owners chasing every inch of droop on rocky trails lean toward uniballs.

Best Upper Control Arms for 4Runner: Six Listings Reviewed

Every pick below is a specific Amazon US listing that names the 4Runner years it covers. Fit can still change with drivetrain, trim and options such as KDSS, so run your truck through the Amazon fit checker before ordering.

1. ICON 58451DJ: Tubular Upper Control Arm with Delta Joint for 2003-Up 4Runner

ICON 58451DJ product photo
Key features
  • ICON Delta Joint outer pivot
  • 1026 DOM steel, CNC bent tubing
  • Serviceable dual stage bushings
  • Listed for 2003-up 4Runner, FJ Cruiser, Lexus GX

ICON Vehicle Dynamics builds suspension systems for trucks and SUVs, and the 58451DJ is its tubular upper control arm for Toyota’s body-on-frame midsize family. The listing names the 2003 and newer 4Runner, the 2007 and newer FJ Cruiser and the Lexus GX, so it spans both the 4th and 5th generation trucks.

The arm is made from 1026 DOM steel tubing that is CNC bent, with CNC machined bushing housings and sleeves. At the outer end it uses the ICON Delta Joint instead of a conventional ball joint, which is the feature most owners shop this arm for. The inner pivots use serviceable dual stage bushings, so they can be refreshed later rather than replacing the whole arm. ICON also sells a separate bushing and sleeve kit for this arm family.

This arm is aimed at a lifted truck that needs revised geometry, not at a stock-height repair. The listing gives no caster figure or lift range in its bullet points, so read the full product details and match the arm to the lift you run. KDSS-equipped trucks and some model years can need different parts, so confirm your year, trim and drivetrain in the Amazon fit checker, and plan for an alignment once the arms are fitted.

View ICON 58451DJ on Amazon

2. Dobinsons UCA59-002K: Pair of Front Upper Control Arms with 3 Degrees of Caster

Dobinsons UCA59-002K product photo
Key features
  • Left and right arms in one kit
  • 3 degrees of caster built in
  • HSLA steel, 5mm wall, powder coated
  • Sankei 555 sealed, replaceable ball joints

Dobinsons is an Australian suspension maker, and the UCA59-002K is a complete pair of front upper control arms. The listing names the 2003 to 2018 4Runner, the FJ Cruiser and the Lexus GX470 and GX460. You get both the left and right arm, new ball joints that come unassembled, OE-style rubber frame bushings already installed, and washers.

The arms have 3 degrees of caster built in, so there is no adjuster to set and nothing to drift out over time. They are made from high strength low alloy steel with a 5mm wall and finished in black powder coat. The ball joints are Japanese-made Sankei 555 units, fully sealed and replaceable, which means a worn joint can be swapped without buying a new arm. Rubber frame bushings keep the ride close to factory.

The listing says the kit works with any lift of 1.5 inches or more, and warns that a correct alignment may not be possible below that height. That makes it a poor fit for a stock truck. The named years end at 2018, so owners of later trucks should look elsewhere. Check your year and trim in the Amazon fit checker, press the joints in before fitting, and book an alignment once the arms are on.

View Dobinsons UCA59-002K on Amazon

SUV on a mountain road

3. Camburg CAM-310036: Uniball Performance Upper Control Arm Kit for 4Runner, FJ and GX

Camburg CAM-310036 product photo
Key features
  • Uniball outer pivot
  • Replaces the factory upper ball joint
  • Listed to increase usable wheel travel
  • Corrects camber and caster

Camburg Engineering is known for long-travel race suspension, and the CAM-310036 is its Uniball Performance Upper Control Arm Kit. The listing says it fits select Lexus GX470, Lexus GX460, Toyota 4Runner, Tacoma and FJ Cruiser models, which places it in the same Toyota platform family as the other lift arms in this guide.

Instead of a ball joint, the outer pivot is a uniball, a spherical bearing that allows a wider range of angle. Camburg’s listing states three aims: removing the factory ball joint it describes as weak, increasing usable wheel travel, and correcting camber and caster after a lift. That combination suits trucks that spend time on rocky trails where the front wheels droop and stuff hard.

The listing is short on specifics and does not name model years, lift range, finish or bushing material, and Camburg sells a near-identical kit, the CAM-310130, that adds the Hilux to its fit list. Open the product details and compare both before ordering. A uniball is also more exposed than a sealed joint, so plan on regular cleaning and inspection, especially on a truck that sees salted winter roads. Confirm fit with the Amazon fit checker and align the truck after installing.

View Camburg CAM-310036 on Amazon

4. Freedom Off-Road Front Upper Control Arms: Pair for 2-4 Inch Lifted 4Runner

Freedom Off-Road UCAs product photo
Key features
  • Sold as a pair
  • 1.5 inch DOM tubing, two-layer E-coat
  • Greaseable, replaceable chromoly ball joints
  • Listed for 2003-2024 4Runner, 2-4 inch lift

Freedom Off-Road sells lift parts for trucks and SUVs, and this listing is a pair of front upper control arms designed for 2 to 4 inch lifts. The title names the 2003 to 2024 4Runner, which covers every 4th and 5th generation truck. Buying both sides in one order keeps the two arms matched for the alignment.

The arms are built from 1.5 inch DOM tubing with welded gussets for strength, and the listing notes provisions for brake and ABS lines where applicable. They are finished with a two-layer E-coating to resist corrosion. The bushings are hardened rubber and replaceable, and the outer pivot is an OE-style chromoly ball joint that is greaseable and also replaceable. The listing says the ball joint angle has been corrected for lifted setups to improve travel and alignment.

These arms make sense for a truck running a mid-height leveling kit or coilovers in the 2 to 4 inch range. They are not designed for a stock-height truck. A greaseable joint asks for a few pumps of grease at service time, which is worth doing on a vehicle driven through salty winters. Confirm your trim and drivetrain in the Amazon fit checker, and schedule an alignment after installing.

View Freedom Off-Road UCAs on Amazon

old SUV in tall grass

5. MOOG RK620064: Front Left Upper Control Arm and Ball Joint Assembly for 4Runner

MOOG RK620064 product photo
Key features
  • Front left upper arm with ball joint
  • Listed for 2003-2024 Toyota 4Runner
  • Also lists FJ Cruiser, GX470 and GX460
  • Factory-style replacement geometry

MOOG, part of DRiV, makes a wide range of steering and suspension parts, and the RK620064 is an OE-style replacement rather than a lift arm. It is a front left upper control arm with the ball joint already installed. The listing names the 2003 to 2024 Toyota 4Runner, the 2007 to 2014 FJ Cruiser, the 2003 to 2009 Lexus GX470 and the 2010 to 2023 Lexus GX460.

MOOG describes the arm as a key suspension part that helps maintain proper wheel alignment and stable handling, built to stand up to everyday road stress. For an owner whose truck still sits at factory height, that is the right goal: restore the original geometry, stop the clunk from a worn joint or bushing and keep the steering feeling as Toyota intended. Having the joint already pressed in saves a separate press job.

This listing covers the driver side only, so order the matching right side arm if both corners are worn, which is common at this age. It does not add caster, so it will not cure the alignment problems that follow a lift. Fit can vary with drivetrain and options, so enter your year, trim and engine in the Amazon fit checker before ordering, and have the alignment checked afterward.

View MOOG RK620064 on Amazon

6. HHCM K640609 and K640610: Front Upper Control Arm Pair for 1996-2002 4Runner

HHCM K640609/K640610 Pair product photo
Key features
  • Right and left front upper arms
  • Listed for 1996-2002 Toyota 4Runner
  • Also lists 1995-2004 Tacoma 4WD and PreRunner
  • 12-month warranty stated in the listing

Parts for the 3rd generation 4Runner are getting harder to find, and this HHCM kit is one of the few listings that names it directly. It contains two arms: K640609 for the front right upper position and K640610 for the front left upper. The listing names the 1996 to 2002 Toyota 4Runner, along with the 1995 to 2004 Tacoma 4WD and the 2000 to 2004 Tacoma PreRunner.

HHCM says the arms are built with reference to original factory standards and tested for quality, with precise tolerances so they install and align like the stock parts. That makes this kit a stock-height repair for a truck with tired upper ball joints or cracked bushings, not a lift upgrade. Replacing both sides at once means the joints and bushings start at the same age, so the truck tracks evenly.

The listing states a 12-month warranty from the seller. It gives few construction details, so read the full product page and compare the arms with the ones on your truck before starting. A 3rd gen that has spent decades on salted roads may have seized frame bolts, so allow extra time for the job. Confirm 2WD or 4WD fit in the Amazon fit checker, and book an alignment afterward.

View HHCM K640609/K640610 Pair on Amazon

Matching a Listing to Your Generation and Lift

Start with the model years, then decide whether you need lift geometry or a stock-height repair.

Listing4Runner years namedPivot typeSuits
ICON 58451DJ2003 and upDelta JointLifted trucks that see trails
Camburg CAM-310036Select 4Runner modelsUniballOwners after maximum travel
Dobinsons UCA59-002K2003-2018Sealed ball jointLifts of 1.5 inches or more
Freedom Off-Road2003-2024Greaseable ball joint2-4 inch lifts on a budget
MOOG RK6200642003-2024Factory-style ball jointStock-height repairs
HHCM K640609/K6406101996-2002Factory-style ball jointWorn 3rd gen front ends
How the best upper control arms for 4Runner trucks in this guide compare by years, pivot and use.

If you are lifting the truck at the same time, new springs and dampers set the ride height the arms are designed around. Our guide to shocks and struts for daily drivers covers what to look for, and doing both jobs in one visit means a single alignment.

black and white close-up of landing gear

Salt, Slush and Exposed Joints in West Michigan

Winters on Grand Rapids roads coat the front suspension in salt brine. Torn boots let it in, and an open uniball takes the full spray. If you choose a uniball arm, plan to inspect and clean it each spring and fall.

Freeze-thaw potholes can bend an arm or knock the alignment out, so watch for a new pull or an off-center wheel. Our checklist of pothole damage signs lists what to look at after a jolt.

pile of gears and engine parts

Worn arms announce themselves the same way on most vehicles, with clunks, wandering and uneven tire wear. Our write-up on Audi control arm failure symptoms describes those noises, and most of it applies to a Toyota truck too.

Fitting UCAs at Home or Booking a Front-End Job

Swapping upper arms is a fair driveway job if you have jack stands, a torque wrench and a ball joint separator. Frame bolts often seize on rust-belt trucks, and rubber bushings should be torqued at ride height. Use the arm maker’s instructions and your service manual for torque values.

Any new upper arm changes caster and camber, so an alignment is part of the job, not an extra. If the old joint already has play, read our notes on worn ball joint warning signs and avoid driving far on it.

colored hex keys on black

Rather leave it to someone else? Our suspension repair service in Grand Rapids handles control arms, ball joints and bushings on foreign and domestic vehicles. Hendrick Hoffman, our owner and head mechanic, carries ASE and State of Michigan credentials in steering and suspension work.

Frequently Asked Questions

Do I need upper control arms for a 2 inch lift on my 4Runner?

Not always. Many trucks with a small leveling kit still align within spec on the factory arms. If the shop cannot bring caster and camber into range, or the upper ball joint is near its limit, aftermarket arms are the fix.

What are the best upper control arms for 5th gen 4Runner trucks?

For a lifted 5th gen, arms with built-in caster such as the ICON 58451DJ, Dobinsons UCA59-002K or Freedom Off-Road set cover the common lift heights. A stock 5th gen with a worn joint is usually better served by an OE-style arm like the MOOG RK620064.

Do 4th gen and 5th gen 4Runners use the same upper control arms?

Many listings cover 2003 and newer trucks together, along with the FJ Cruiser and Lexus GX. Some exclude certain years, drivetrains or KDSS trucks, so always check the exact listing and the Amazon fit checker.

Do I need an alignment after replacing upper control arms?

Yes. New arms change caster and camber even at stock height, and lift arms are designed to be set on an alignment rack. Skipping it can lead to a pull and fast tire wear.

Is your 4Runner knocking over bumps or refusing to track straight after a lift? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or schedule a suspension inspection on our contact page.

Busy until evening? Use our after-hours key drop and park the truck at our shop, 456 Carrier St NE, Grand Rapids.