456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Pads, Pucks and Lift Height: The Best Car Jack for BMW

best car jack for bmw: workshop wall with wooden shelves and tools

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

Slide a flat steel saddle under a BMW sill and you can hear the trouble before you see it: a crack from the plastic jack pad or a bent pinch weld. The best car jack for BMW owners is a floor jack that fits under the car, reaches the factory jack points, and works with an adapter that keys into those square pads.

Below: how BMW jack points work, how to size a jack, and six options, including a puck adapter. If your car sits very low, our roundup of the best low profile floor jack for cars goes deeper on entry height.

Quick answer

What kind of jack should a BMW owner buy?

Most BMW owners do well with a 2 to 3 ton aluminum floor jack that starts under 4 inches, such as the ARCAN A20017, plus a puck adapter like the imUfer set that seats in the square jack pads. X5 and X3 owners should look for a taller reach, such as the BIG RED T83006.

Our Quick Picks

Three picks that cover most BMW garages: a light aluminum jack for sedans, a tall-reach jack for X models, and a puck adapter for the factory jack pads.

ARCAN A20017 product photo
Sedan pick

ARCAN A20017

2 ton, 3.54 to 19.88 in.

A light aluminum jack that slides under most BMW sedans and coupes.

Suits3, 4 and 5 Series owners
View on Amazon →
BIG RED T83006 product photo
X model pick

BIG RED T83006

3 ton, 5-7/8 to 20-7/8 in.

A tall-reach steel jack for X3, X5 and other high-riding BMWs.

SuitsX3 and X5 owners
View on Amazon →
imUfer Jack Pad Adapter product photo
Pad adapter

imUfer Jack Pad Adapter

4 pucks, billet aluminum

Pucks that key into BMW jack pads so a floor jack lifts cleanly.

SuitsAny floor jack used on a BMW
View on Amazon →

How BMW Jack Points Work

Look along the sill behind the front wheel and ahead of the rear wheel on most BMWs and you will find a small rubber or plastic block with a square hole in it. That block is the jack pad, and the square hole is shaped for the tongue of the factory scissor jack. It spreads the load into a reinforced part of the body so the sheet metal around it does not fold.

A floor jack has a round, flat saddle, so it presses on the edges of that block instead of locking into it. Do that often enough and the pad cracks, shifts or falls out, and a jack placed beside a missing pad can crease the rocker panel. A puck adapter fixes the mismatch by keying into the pad. Inspect the pads first, since a cracked or missing one needs replacing before you lift there.

Many recent BMWs on run-flat tires leave the factory without a spare wheel or a jack at all. Check the trunk floor before a flat tire does it for you.

Sizing a Jack for a 3 Series or an X5

Two numbers matter more than the tonnage printed on the box. The first is the minimum height, the lowest point of the saddle, which has to clear the sill or front lip of a lowered or M Sport 3 Series. The second is the maximum height, which decides whether you can lift an X5 far enough to hang a wheel and still fit a stand underneath.

Capacity still counts. A floor jack lifts one corner or end, but a heavy SUV loads it hard, so leave margin. The gross vehicle weight rating on the driver’s door jamb label gives you a ceiling to compare against the jack’s rating.

Aluminum frames are lighter to carry, while steel frames are heavier but sturdy. For a starter garage list beyond the jack, see our guide to the best car maintenance tools for beginners.

Best Car Jack for BMW: Six Options Reviewed

Capacities and lift ranges below come from the Amazon listings. Measure your own car’s sill height and confirm the jack points in your owner’s manual before you buy.

1. ARCAN A20017: 2 Ton Aluminum Low Profile Floor Jack with Dual Pump Pistons

ARCAN A20017 product photo
Key features
  • 2 ton (4,000 lb.) capacity
  • 3.54 to 19.88 in. lift range
  • Aircraft-grade aluminum build
  • Listed to ASME PASE-2019

The ARCAN A20017 is a 2 ton floor jack with an aluminum frame that the listing calls aircraft-grade. Its rated 4,000 lb. capacity covers one corner or one end of a typical 3 Series, 4 Series or 5 Series sedan with room to spare. Because the frame is aluminum rather than steel, it is easier to carry from a shelf to the car or lift into a hatch for a weekend at a friend’s garage.

The listed lift range runs from 3.54 inches at the bottom to 19.88 inches at the top. That low starting point lets the saddle slip under the sill of most BMW sedans without first driving onto boards, and the high end leaves room to set a stand and pull a wheel. Arcan lists dual pump pistons that bring the saddle up to the jack point quickly, a reinforced lift arm for torsion control, and a rubber saddle pad to reduce marring.

The listing also states compliance with the ASME PASE-2019 safety standard and a one year Arcan warranty. Pair it with a BMW puck adapter so the saddle seats in the factory pad rather than pressing on its edges. A heavy X5 or X7 is better matched to a 3 ton jack with more reach.

View ARCAN A20017 on Amazon

2. SATA 3-Ton Aluminum Floor Jack: Low Profile with Dual-Piston Rapid Lift Pump

SATA 3-Ton Aluminum product photo
Key features
  • 3 ton (6,600 lb) capacity
  • 3-3/4 to 19-1/8 in. lift range
  • Factory tested to 1.5x rating
  • Overload and slow-release valves

SATA’s 3-ton aluminum floor jack suits a household where a BMW sedan shares the garage with an X3 or a similar SUV. The listing rates it at 6,600 lb and says each unit is tested to 4.5 tons, one and a half times its rating, before it leaves the factory. SATA also says the aluminum body is about 30 percent lighter than its steel model, which helps if you move the jack around often.

The listed range starts at 3-3/4 inches and tops out at 19-1/8 inches. That entry height clears many BMW sedans at the sill, though a lowered car with a deep front lip may still need a lower jack or a short ramp. A dual-piston pump, which SATA says reduces handle effort and lifting time, brings the saddle to the jack point in fewer strokes.

Two safety features are listed: an overload protection valve that stops the jack from lifting past its rating, and a slow-release system for controlled lowering. That controlled drop is useful when you lower the car onto jack stands at a BMW pad and want the weight to settle gently. Add a puck adapter, and keep the stands under the car before any work starts underneath.

View SATA 3-Ton Aluminum on Amazon

Mechanic moving an engine on a stand in a shop

3. Jack Boss 3 Ton: Aluminum and Steel Low Profile Racing Floor Jack with Dual Pistons

Jack Boss 3 Ton product photo
Key features
  • 3 ton (6,600 lbs) capacity
  • 3-15/16 to 18-5/16 in. lift range
  • Aluminum body on a steel frame
  • Listed to ANSI/ASME PASE

The Jack Boss 3 ton floor jack mixes an aluminum body with a welded steel frame, a middle path between a light all-aluminum jack and a heavy all-steel one. Its listing rates it at 6,600 lbs and says it is factory tested to 4.5 tons. The jack measures 28.3 by 13.7 by 7.8 inches, so it fits on a garage shelf or under a workbench without much trouble.

The listed lift range runs from 3-15/16 inches to 18-5/16 inches. That minimum clears the sill on many BMW sedans and wagons, and the maximum works for a 3 Series sedan with a jack stand set beside the saddle. A dual-piston pump cuts the number of strokes, and the rubber saddle helps protect lifting points from scratches, according to the listing.

Steel casters with swivel front casters let you roll it into place along the sill, and the two-piece handle comes apart for storage. Jack Boss states the jack meets ANSI/ASME PASE safety standards and carries a limited one year warranty. A full-size X5 owner will want more top-end reach, and every owner should still use a puck adapter in the factory jack pad.

View Jack Boss 3 Ton on Amazon

4. BIG RED T83006 Torin: 3 Ton High Lift Floor Jack with Extra Saddle for SUVs

BIG RED T83006 product photo
Key features
  • 3 ton (6,000 lb) capacity
  • 5-7/8 to 20-7/8 in. lift range
  • Extra long saddle neck
  • Safety bypass against overloading

The BIG RED T83006 from Torin is a steel trolley jack built for taller vehicles, which makes it a natural match for a BMW X3, X5 or X7. The listing rates it at 3 tons, or 6,000 lb, and gives a minimum height of 5-7/8 inches with a maximum of 20-7/8 inches. That top figure is the tallest in this list, so you reach full wheel droop on an SUV with fewer pumps and no stacked blocks.

An extra long saddle neck, which Torin says saves time on higher vehicles, comes with an extra saddle in the box. Two large steel casters and two 360-degree swivel casters move it across a concrete floor, and the listing gives a 24.5 inch handle. A single piston quick lift pump raises the saddle, and a safety bypass system prevents overloading.

The trade-off is the starting height. At 5-7/8 inches it will not slide under most BMW sedans, and the steel build makes it heavier to carry than the aluminum jacks here. It suits an owner who mainly lifts X models, with a puck adapter on the saddle and stands rated for the SUV. Torin includes a limited one year manufacturer warranty.

View BIG RED T83006 on Amazon

Polished multi-spoke wheel

5. IMAYCC Car Jack Kit for BMW and MINI: 2.5 Ton Scissor Jack with 2 Jack Pads

IMAYCC Scissor Jack Kit product photo
Key features
  • 2.5 ton (5512 lbs) rating
  • 5.1 to 16.79 in. lift range
  • Two BMW rubber jack pads
  • Lug wrench and storage bag

IMAYCC’s car jack kit is a trunk-size answer for the many BMWs that ship without a spare or a jack. It centers on a scissor jack the listing rates at 2.5 tons, or 5512 lbs, with a lift range of 5.1 to 16.79 inches. The listing names a long list of 1, 3, 5, 6 and 7 Series chassis plus X1, X3, X5 and X6 models, from E46 and E90 cars to F30 and F10.

The kit includes the jack, two rubber BMW jack pads, a ratchet wrench, a lug wrench with 17/19 mm and 21/23 mm ends, gloves and a storage bag. IMAYCC says the jack is made of cold-rolled steel with an enlarged base for stability, and the pads protect the car from the steel beam while lifting. Everything packs into the bag so it can ride under the trunk floor.

This is a roadside tool, not a garage jack, so it is slower to raise and less stable than a floor jack. The listing warns it does not fit some BMW sports models with less than 130 mm of ground clearance, so confirm year, model and chassis on Amazon before buying. Use it for a wheel change, never to work under the car.

View IMAYCC Scissor Jack Kit on Amazon

6. imUfer Jack Pad Adapter for BMW: Billet Aluminum Puck Set of 4

imUfer Jack Pad Adapter product photo
Key features
  • Set of 4 aluminum pucks
  • CNC-machined billet aluminum
  • Anodized black finish
  • Seats in factory jack points

The imUfer jack pad adapter is the piece that lets any of the floor jacks above work properly on a BMW. It is a puck with a square boss on one side that drops into the factory jack pad and a flat face on the other that sits on the jack saddle or a jack stand. The listing describes solid billet aluminum, machined by CNC and anodized black, and the package holds four pucks.

imUfer lists a long run of compatible chassis, including E46, E90, E92, E39, E60, E70 and E71 models, the X3, X5 and X6, M3, M5 and M6, and newer F01, F02, F10 and F30 cars. With four in the set, you can leave one on the jack and one on each stand while the car is up. The listing says the adapter helps prevent rocker panel and jack point damage and keeps the jack away from painted surfaces.

Check that the base of the puck sits flat on your jack’s saddle before the first lift, since a puck that overhangs a small saddle can tip. It cannot fix a pad that is already cracked or missing, so replace damaged pads first. Confirm your year and model on Amazon before ordering.

View imUfer Jack Pad Adapter on Amazon

The Six Compared by Reach

The heights shown are each listing’s saddle range.

ProductListed capacityListed lift rangeSuits
ARCAN A200172 ton3.54 to 19.88 in.3 and 5 Series sedans
SATA 3-Ton Aluminum3 ton3-3/4 to 19-1/8 in.Mixed sedan and SUV garages
Jack Boss 3 Ton3 ton3-15/16 to 18-5/16 in.Sedans and smaller X models
BIG RED T830063 ton5-7/8 to 20-7/8 in.X3, X5 and taller models
IMAYCC Scissor Jack Kit2.5 ton5.1 to 16.79 in.Trunk kit for roadside flats
imUfer Jack Pad AdapterNot statedAdds puck heightAny floor jack on BMW pads
Six BMW jacking options compared by listed capacity, saddle range and the cars they suit

Sedan owners should weigh entry height; X5 owners should weigh reach. For most garages the best car jack for BMW work is simply the one that matches your car’s height, and whichever jack you pick, a puck adapter in the BMW pad keeps the saddle from chewing the sill.

Wrenches on a pegboard above screwdrivers

Lifting a BMW Safely in a Michigan Garage

A jack lifts; it does not hold. Never put any part of your body under a BMW held only by a jack, however good the jack is. OSHA’s workplace rules for jacks say the load should be cribbed, blocked or otherwise secured as soon as it is raised, and that the base should be blocked when the ground is not firm.

Work on a flat, solid concrete floor, not gravel, asphalt on a hot day or a sloped driveway. Chock the wheels that stay down and set the parking brake. Lift only at the jack points the manual shows, then lower the car onto rated jack stands before you reach under it.

Hands turning a wrench on an engine

West Michigan winters add their own problems. Wipe salt slush off the floor where the jack rolls, and expect a slower pump stroke in a cold, unheated garage.

When the wheel goes back on, snug the lug bolts, lower the car, then torque them to the figure in your owner’s manual in a star pattern. A click wrench from our guide to the best torque wrench for lug nuts makes that step simple.

When the Job Belongs on a Shop Lift

A floor jack and stands handle tire swaps, brake pads and a look at the suspension. Jobs that need the whole car in the air, or a torn-out pad, belong on a two-post lift.

Cars parked in an underground garage

Our factory scheduled maintenance in Grand Rapids covers the service items your BMW’s maintenance schedule calls for, and our foreign car repair team can look at a damaged jack pad or a creased rocker before rust gets a foothold.

Frequently Asked Questions

Where are the jack points on a BMW?

On most models they are square rubber or plastic pads on the underside of the sill, one behind each front wheel and one ahead of each rear wheel. Your owner’s manual shows the exact spots for your car.

Do I need a jack pad adapter for my BMW?

It is strongly advised. A flat floor jack saddle presses on the edges of the factory pad and can crack it, while a puck adapter keys into the square hole and spreads the load the way the factory jack does.

What is the best car jack for BMW X5 owners?

Look for a 3 ton floor jack with a tall maximum height, such as the BIG RED T83006 with its listed 20-7/8 inch reach, and pair it with a puck adapter and jack stands rated for the vehicle.

Cracked jack pad, a seasonal tire swap you would rather skip, or service that needs the car on a lift? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a visit through our contact page.

Stuck at work until after five? Our after-hours drop-off at 456 Carrier St NE, in Grand Rapids’ Creston area, lets you leave the BMW on your own schedule.