As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A Tesla hides most of its floor behind a large battery pack, so you cannot slide a stand under any flat spot that looks strong. The best jack stands for Tesla owners are the ones that carry the car’s weight with margin, sit cleanly under the approved lift points and protect the finish with a flat or rubber contact.
Below, we cover what Tesla says about lifting, then review five stands that suit a Model 3 or Model Y in a home garage. For the general basics on capacity and lock styles, our guide to jack stands for the home garage is the place to start.
Quick answer
Which jack stands work under a Tesla Model 3 or Model Y?
A 3 ton class pair with a flat or rubber-padded saddle is the usual choice. The AME INTL 14980 has a flat rubber top, and the FITHOIST 3 Ton ships with rubber pads. Use stands only under Tesla’s designated lift points, never under the battery or side rails, and never with the charge cable connected.
Our Quick Picks
Three quick picks for Tesla owners: a flat rubber top, a pair that ships with rubber pads, and a plain steel double-lock pair. All five stands are reviewed below.

AME INTL 14980
Flat, rubber-capped saddles instead of a toothed V cradle.

FITHOIST 3 Ton Jack Stands
Double-lock steel stands that come with rubber saddle pads.

Torin 3 Ton Double Locking Stands
Forged steel, welded frame and a large saddle area.
What Tesla Says About Lifting the Car
Tesla’s guidance is short and strict. The Model 3 owner’s manual section on jacking and lifting tells you to place lift pads under the designated body lift points only. It warns against lifting under the battery or the side rails, and says damage from lifting anywhere else is not covered by the warranty.
The same page adds a rule that catches people out: never raise the car while the charge cable is connected, even if it is not charging. Unplug it before the jack comes out. The Model Y manual carries the same warnings.
Note what the manual does not say. It describes a two-post lift procedure and does not lay out a floor jack and jack stand method. That leaves home mechanics with a real puzzle, because the jack and the stand both want the same approved point. Check Tesla’s service information for your car, or ask a shop, before you settle on where each stand goes.
What Makes a Stand a Good Match for a Tesla
Teslas are heavy for their size because of the battery, but a pair of stands only holds one end of the car. Find the gross vehicle weight rating on the label in the driver’s door jamb and pick a pair rated well above half of it. Every stand below is a 3 ton class design, which leaves sensible room for either model.
- Contact surface: a flat rubber top or a rubber saddle pad gives an even, soft contact. Many owners also use rubber lift-point pucks that seat in the lift point and give the stand something to bear on.
- Height range: a Tesla’s lift points sit low, so most 3 ton stands reach them easily. Check the minimum height too, since a tall stand needs the car raised further before it slides in.
- Two locks: a ratchet with a separate pin gives a backup if the pawl is knocked. A pin you can see is easy to check before you go under.
- Footprint: a wider base resists tipping when you lean on a breaker bar.
Best Jack Stands for Tesla: Five Stands Worth a Look
The stands below cover the main needs, from a soft flat top to a plain steel pair you pad yourself. Capacities and heights are quoted as each Amazon listing states them.
1. AME INTL 14980: 3 Ton Flat Top Jack Stands with Rubber Cushion

- 3 ton capacity per stand, sold in pairs
- Flat top rubber pad grips the lifting point
- 13 to 21.5 in. height range
- Zinc plated post, powder coated base
The AME INTL 14980 swaps the usual V-shaped saddle for a flat top with a rubber cushion. AME describes the pad as gripping the lifting point, and that shape is the main reason it appears on a Tesla list. A flat rubber surface spreads the contact over a wider area than a narrow notch, which is what many owners want under a body lift point or a lift-point puck.
Each stand is rated at 3 tons, and the listing sells them as a pair. Height runs from 13 inches at the bottom to 21.5 inches at the top, so the stand starts taller than many 3 ton ratchet stands. That suits a car you have already raised a good way with a floor jack, but measure first if your jack only lifts the car a little.
The post is zinc plated and the base is powder coated, two finishes aimed at slowing rust in a garage where road salt drips off the car through the winter. Each stand weighs about 12 pounds according to the listing. AME pitches these at low profile and custom cars, and the flat top will not cradle a round axle tube the way a V saddle does, so they are a poor match for trucks with solid axles.
2. FITHOIST 3 Ton: 6,600 lb Double Pin Jack Stands with Rubber Pads

- 6,600 lb capacity per pair
- Ratchet bar lock plus removable safety pin
- 11.3 to 16.5 in., 10 positions
- Thick rubber pads included
FITHOIST ships this pair with thickened rubber pads that sit on the saddles, which saves you buying pads separately. The maker says the pads protect the underside from scratches and improve grip while the car is supported. For a Tesla, where you want a soft and even contact under the designated lift points, that bundled extra is the reason it made this list.
The listing rates the pair at 6,600 pounds, so read that as a figure for both stands together. Height adjusts in 10 positions from 11.3 to 16.5 inches using a cast iron ratchet bar. A removable safety pin passes through the post as a second lock, so the stand has a backup if the ratchet pawl is ever knocked out of place.
The frame is rigid steel on a wide pyramid base, and the listing says the stands meet US safety standards without naming the specific standard, so treat that line with some care. Pyramid feet work well on a level concrete floor and less well on asphalt on a hot day. This is a sensible starting point for a sedan or crossover, but a lifted truck will need taller stands than these.
View FITHOIST 3 Ton Jack Stands on Amazon

3. Torin 3 Ton: Double Locking Steel Jack Stands, 11-5/16 to 16-7/8 in.

- 3 ton (6,000 lb) load capacity
- 11-5/16 to 16-7/8 in. height range
- Sawtooth multi-position ratchet bar
- 7.95 x 7.2 in. pyramid foot base
Torin’s double locking stand is a straightforward steel design with no frills, built for cars and smaller SUVs. The listing quotes a 3 ton (6,000 pound) load capacity and a height range of 11-5/16 to 16-7/8 inches. That range sits well for a car raised on a floor jack, since a Tesla’s lift points are not far off the ground.
The frame is high-grade forged steel with welded joints, and the saddle has a large surface area for steady contact with the load. Height is set with a multi-position ratchet bar that has a sawtooth profile, so it clicks up quickly and locks in place. The pyramid foot base measures 7.95 by 7.2 inches, which gives a stable footprint on a level slab.
There is no rubber pad on this stand, so if you want a soft contact you will need to add a rubber lift-point puck or saddle pad of your own. Torin’s own listing says these suit most 3 ton vehicles and are not meant for big pickups or large off-road SUVs. For a Model 3 or Model Y in a home garage, it is a simple, well-proportioned pair that does one job without extras.
View Torin 3 Ton Double Locking Stands on Amazon
4. ESCO 10498: 3 Ton Jack Stand with Rubber Lifting Pad and 12 x 12 in. Base

- 6,000 lb (3 ton) capacity per stand
- Anodized post with rubber lifting pad
- 13.2 to 21.5 in., 10 positions
- 12 x 12 in. powder coated base
ESCO’s 10498 is sold individually, so plan on buying two for one end of the car. Each stand carries 6,000 pounds, or 3 tons, and the post is anodized with a rubber lifting pad on top. That pad gives a cushioned contact, which is what most Tesla owners look for when they place a stand under a body lift point.
The base is the other standout. At 12 by 12 inches it is far broader than the pyramid feet on most ratchet stands, and the square shape resists tipping when you lean on a wrench under the car. The base is powder coated to resist rust and corrosion, which matters in a Michigan garage that sees wet, salty floors for months at a time.
Height adjusts through 10 positions from 13.2 to 21.5 inches, so the bottom setting is taller than a typical car stand. ESCO says the stand was tested to ASME standards by an A2LA certified testing facility. Because it is sold one at a time, a pair costs you two orders, and the tall minimum height means you need to lift the car far enough to slide it in before you lower the weight onto it.
View ESCO 10498 Jack Stand on Amazon

5. ROADTEK 3 Ton: Double Locking Jack Stands with Round Steel Base and Release Knob

- 3 ton (6,000 lb) capacity per stand
- 7.85 in. diameter one-piece steel base
- Ratchet bar plus chained safety pin
- 11.3 to 16.6 in., 10 levels
ROADTEK takes a different route with the base. Instead of a welded pyramid, this stand sits on a one-piece round steel base 7.85 inches across, which the maker says avoids weld fractures and resists deformation under a long lift. Each stand is rated at 3 tons, or 6,000 pounds, and the listing sells them as a pair.
Height is set with a 10-level cast iron ratchet bar that runs from 11.3 to 16.6 inches. The second lock is a metal pin that hangs on a long chain, so it stays with the stand instead of rolling under the car. Release is handled by a knob rather than the usual lever, and ROADTEK says the knob lets you lower the bar in a more controlled way, which helps prevent a sudden drop and pinched fingers.
The saddle is concave, designed to fit an edge on the vehicle and reduce the chance of slipping. It has no rubber pad, so add a puck or pad if you want to protect the finish around a Tesla’s lift points. A rubber-covered carry handle lets you pick up both stands with one hand, a small thing that makes setup quicker.
View ROADTEK 3 Ton Jack Stands on Amazon
How the Five Stands Compare
Use this table to narrow down the best jack stands for Tesla work in your own garage. Line the capacity figures up on the same basis first, since some makers quote each stand and others quote the pair.
| Stands | Rated capacity | Height range | Top surface |
|---|---|---|---|
| AME INTL 14980 | 3 ton per stand | 13 to 21.5 in. | Flat rubber cushion |
| FITHOIST 3 Ton | 6,600 lb per pair | 11.3 to 16.5 in. | Saddle with rubber pads included |
| Torin 3 Ton Double Locking | 6,000 lb | 11-5/16 to 16-7/8 in. | Large steel saddle |
| ESCO 10498 (sold singly) | 6,000 lb per stand | 13.2 to 21.5 in. | Rubber lifting pad |
| ROADTEK 3 Ton | 6,000 lb per stand | 11.3 to 16.6 in. | Concave steel saddle |
The AME and ESCO stands start at 13 inches or more, so the car must be raised a little higher before they fit. Bare steel saddles carry the load fine but can mark the underbody unless you add a pad or puck.

If your floor jack struggles to get under a low car, our roundup of low profile floor jacks for cars covers saddle height and reach. A creeper, chocks and a torque wrench round out the job, and our list of car maintenance tools for beginners walks through the rest of that kit.
Supporting a Tesla Safely in a West Michigan Garage
The steps barely change from one stand to the next. Go slowly, because an EV’s weight sits low and centered, and a stand set slightly off the lift point can slip as the load settles.
- Unplug and park: disconnect the charge cable, park on level concrete, put the car in Park and chock the wheels that stay down.
- Use the approved points: find the body lift points shown in your owner’s manual and fit a rubber puck if you use one.
- Raise, then set the stand: lift slowly, set the stand at the height you need, fit any pin and lower the car until its weight rests on the saddle.
- Test before you crawl under: give the car a firm push at the bumper. If anything shifts, lift it back up and reset.
Winter adds its own risk here. Melting slush and road salt leave garage floors wet and gritty from November to March, and a stand foot can skate on a slick patch. Sweep and dry the spot first, and wipe salt off the stands when you are done so the ratchet and pin holes stay clean.

Stands suit short jobs such as a tire rotation or a brake check. Long jobs, or work that loads up suspension bolts, belong on a lift. Whichever of the best jack stands for Tesla work you choose, it is a support for quick tasks, not a substitute for a lift.
When a Shop Lift Makes More Sense
An EV still needs regular care. Tires can wear faster under the extra weight, brake parts can corrode from light use in salty months, and suspension parts work hard over freeze-thaw potholes. Much of that is easier to inspect with the whole car raised on a two-post lift and its lift arm pads under the approved points.

Our factory scheduled maintenance service in Grand Rapids follows the intervals in your car’s maintenance schedule with the car up on a lift. If you notice a grinding brake or a clunk from the front end while you are under the car, we can check the brakes and suspension and tell you what we find.
More Buying Guides
Frequently Asked Questions
Where do jack stands go on a Tesla?
Tesla’s manual approves only the designated body lift points and warns against the battery and side rails. It does not describe a jack stand procedure, so confirm stand placement in Tesla’s service information or with a shop before you go under the car.
Are 3 ton jack stands enough for a Model Y?
A pair only holds one end of the car, so a 3 ton class pair leaves good margin for a Model 3 or Model Y. Check the weight rating on your door jamb label and read whether the stand’s rating is per stand or per pair.
Do I need rubber pads or pucks on my stands?
They are a good idea. A bare steel saddle can mark the underbody, while a rubber pad or lift-point puck spreads the contact. The AME INTL 14980 and ESCO 10498 have rubber tops, and the FITHOIST pair includes pads.
Can I lift my Tesla while it is plugged in?
No. Tesla says never to raise the car while the charge cable is connected, even when it is not charging. Unplug it before you start.
Rather leave the lifting to us? Call 456 AutoFix at 616-279-3832 on any weekday between 8am and 5pm, or send us a message through the contact page to set up a time.
Busy during shop hours? Drop the keys in our after-hours box at 456 Carrier St NE in Creston and we’ll handle the rest.
