As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
Lifting a Porsche is the easy half of the job. Holding it up safely while you lie beside it is the half that matters, and the best jack stands for Porsche cars do it without denting a sill pad or sliding off a smooth underbody point.
This guide explains what changes when the car on the jack is a 911, a Cayman or a Cayenne, then reviews five rated pairs from 2 to 6 tons. For a broader look at stands for any make, read our guide to jack stands for a home garage.
Quick answer
What jack stands should a Porsche owner buy?
Buy a matched 2 to 3 ton pair with a flat saddle or rubber top that sits squarely on the factory support point. The ESCO 3 Ton Performance Kit adds a rubber flat top and a tall range for a Cayenne, the BIG RED T42202 suits a 911 or Cayman, and the AUTOWN pair has a wide flat saddle.
Our Quick Picks
Three pairs that cover a sports car, a flat support pad and a tall SUV; all five are reviewed below.

ESCO 3 Ton Performance Jack Stand Kit
Swap between a rubber flat top and an axle post to suit the support point.

BIG RED T42202 2 Ton Jack Stands
A compact steel pair sized for the lighter end of the Porsche range.

AUTOWN 3 Ton Jack Stands
A broad flat saddle spreads the load on a sill pad or flat section.
How a Porsche Changes the Jack Stand Shopping List
Most stand guides talk about capacity first. On a Porsche, capacity is rarely the problem: one end of even a Cayenne puts far less on a pair than a 3 ton rating allows. The questions that decide the purchase are where the stand will touch the car and how high it has to reach.
- Contact surface: many Porsches use small pads or reinforced sections under the sills rather than a long exposed pinch weld. A deep V-shaped saddle can bite into a pad, so a flat or rubber-topped saddle is often the cleaner match.
- Height range: a 911, Boxster or Cayman needs only modest lift for wheel and brake work. A Cayenne or Macan sits higher, and a taller stand keeps the car level once the jack comes out.
- Base size: the stand has to fit beside the jack under a short sill without the two touching.
- Locking method: ratchet stands adjust quickly, while a second locking pin adds a positive backup that some owners prefer under a heavy SUV.
Lift points are not a guess. SAE International sets out how carmakers should design and mark them in SAE J2184 on vehicle lift points for service garages, and your owner’s manual shows the points for your model and year. Treat that diagram as the rule and any forum tip as a suggestion.
Sharing the Lift Points Between Jack and Stand
Here is the puzzle every Porsche owner meets on day one. The jack wants the factory point, and so does the stand. Owners usually solve it in one of two ways, and the right one depends on your model.
- Lift elsewhere, support at the point: raise one end at a central point the workshop manual approves, then set both stands under the side points and lower the car onto them.
- Lift at the point, support nearby: use the jack at the sill pad, then place the stand at a nearby structural point the manual allows, such as a suspension mount or subframe section.
Never set a stand on a plastic underbody tray, an exhaust part, a fuel or brake line or a battery housing. On electric models such as the Taycan, the high-voltage battery forms much of the floor, so stay strictly with the marked points. If you are unsure, pick the floor jack first; our floor jack guide for Porsche owners covers reach and pucks.
Best Jack Stands for Porsche: Five Pairs Reviewed
Heights and ratings come from each Amazon listing or the maker’s page. Measure the gap at your own support point before you order.
1. ESCO 3 Ton Performance Jack Stand Kit: 13.2 to 21.5 in. Stands with Rubber Flat Top

- 6,000 lb rating per stand
- 13.2 to 21.5 in., 10 positions
- Anodized post, powder coated base
- Rubber flat top and axle top posts
ESCO’s Performance stand looks different from the stamped steel ratchet stands most people own. A round, powder coated base carries an anodized post that locks with a pin, and the Amazon listing rates each stand at 6,000 lb with a range of 13.2 to 21.5 inches across 10 positions. That tall top end pairs well with a Cayenne, Macan or Panamera.
The detail that suits a Porsche is the top of the post. ESCO’s page for the Performance kit describes two interchangeable posts: a removable rubber padded flat top for a body support point and a conventional axle saddle for round surfaces. The flat rubber face sits on a sill pad or a reinforced section without a V-notch digging in, and the axle post covers a suspension or axle job later. ESCO says the design is tested to ASME standards by an A2LA certified facility.
Two points to check before ordering. The 13.2 inch minimum means a sports car must be raised a fair way before a stand slides under, so it is less handy for a quick wheel swap on a Cayman. ESCO’s own page lists the kit as a single stand, while this Amazon listing says two are included, so confirm the quantity in the listing before you buy a second.
View ESCO 3 Ton Performance Jack Stand Kit on Amazon
2. BIG RED T42202 Torin: 2 Ton Steel Ratchet Jack Stands, 10-13/16 to 16-9/16 in.

- 2 ton (4,000 lb) pair rating
- 10-13/16 to 16-9/16 in. range
- Sawtooth ratchet bar
- Forged steel, pyramid base, ASME tested
A 911, Boxster or Cayman is a light car by jack stand standards, and this 2 ton BIG RED pair is sized for that job. The listing gives a 4,000 lb capacity and a height range of 10-13/16 to 16-9/16 inches. The low starting point means the stand fits under a sports car that has only been raised a few inches, which keeps jacking to a minimum.
Construction follows the familiar Torin pattern: a forged steel frame with welded joints, a wide pyramid base for stability on concrete and a multi-position ratchet bar with a sawtooth profile. You lift the bar until it clicks into the height you want, then flip the handle down to lock it. The saddle has a large contact area for its size, and the listing states that the stands are tested to meet ASME standards.
Because the frame is smaller than a 3 ton stand, the pair is easier to tuck beside a jack under a short sill and lighter to carry to the driveway. The trade-off is reach and margin. A Cayenne or Panamera is better served by a taller, higher rated pair, and the V-shaped saddle may need a rubber pad between it and a factory support point. For a coupe or roadster, it covers seasonal jobs neatly.
View BIG RED T42202 2 Ton Jack Stands on Amazon

3. GEARWRENCH GWJS2T: 2 Ton Ratcheting Jack Stands with Double Lock Pin

- 2 ton pair, pack of 2
- Double lock pin design
- Ductile iron ratcheting bar
- Meets ASME PASE-2019
GEARWRENCH is better known for wrenches and sockets, but its stand line follows the same approach of plain, well-specified hardware. The GWJS2T is the 2 ton member, sold as a pack of two, and it pairs a ductile iron ratcheting bar with a double lock pin. The pin passes through the stand once the height is set, so there is a second lock in addition to the ratchet pawl.
The rest of the design is aimed at stability. Large welded feet spread the load over more of the floor, which helps on a slab that is not perfectly flat, and a wide saddle gives the support point more surface to rest on. GEARWRENCH states that the stands meet ASME PASE-2019 safety and performance requirements, a standard for portable automotive service equipment.
The Amazon listing does not give minimum and maximum heights, so check the product images or the spec details on Amazon against the gap you measured under your car before ordering. As a 2 ton pair it suits the lighter sports cars rather than a Cayenne or Panamera. For an owner who wants a backup pin under a 911 or Cayman during brake or suspension work, it is a tidy choice.
View GEARWRENCH GWJS2T 2 Ton Jack Stands on Amazon
4. AUTOWN 3 Ton Jack Stands: 11 to 16.7 in. Dual Lock with Wide Flat Saddle

- 3 ton (6,600 lb) per stand
- 11 to 16.7 in., 10 positions
- Ratchet plus auxiliary pin lock
- Wide, thick flat saddle
AUTOWN’s pair stands out for its saddle. Instead of a narrow V-notch, the listing describes a widened, thickened flat saddle meant to spread pressure over the chassis and avoid scratches. That shape suits Porsches that support on a flat pad or reinforced panel rather than a long pinch weld, though a rubber pad on top is still a sensible extra layer.
Each stand is rated at 3 tons (6,600 lb) and adjusts from 11 to 16.7 inches in 10 positions on a heavy-gauge steel rack. Locking is a dual system: the main ratchet holds the height, and an auxiliary pin passes through as a backup against slipping. A large reinforced base adds stability, and the listing covers the pair with a one year limited warranty against defects.
AUTOWN is a newer name than the established brands here, and the listing says it is built to meet industry safety standards without naming a specific one, so weigh that if a certification matters to you. Its own notes on electric cars recommend a separate rubber pad and factory lift points only, which is sound advice for a Taycan too. The height range suits a 911 or Macan for wheel and brake work.
View AUTOWN 3 Ton Jack Stands on Amazon

5. Omega Lift 6 Ton Jack Stands: 16 to 23-1/2 in. Pair with Handle Lock and Pin

- 6 ton pair rating
- 16 to 23-1/2 in. lift range
- Handle lock plus mobility pin
- Meets ANSI/PALD standards
Omega Lift’s 6 ton pair is the tall option here, and it only makes sense for the larger Porsches. The listing gives a lifting range of 16 to 23-1/2 inches, so a Cayenne or Panamera can sit high enough to give you room for brake, suspension or exhaust inspection. On a 911 or Cayman, that 16 inch minimum is more than most owners want to jack up to.
The frame is stamped steel with a welded design and a wide pyramid base, and height is set on a cast ductile iron ratchet bar with a sawtooth profile. Two locks back it up: a handle lock and a mobility pin. Omega points out that the pin can be checked visually from a distance, and with the pin engaged you can carry the stand without the ratchet bar dropping out.
Omega states that the stands meet or exceed ANSI/PALD standards. The extra rating does not change how the car is supported, but the bigger frame and base give a steadier feel under a heavy SUV. The saddle is plain steel, so plan on a rubber pad for a factory support point, and measure the stand’s footprint against the space next to your jack.
View Omega 6 Ton Jack Stands on Amazon
Which Pair Suits Which Porsche
The table groups the five pairs by the cars and jobs they fit most naturally. All of them carry far more than one end of a Porsche weighs, so the choice comes down to height, footprint and saddle.
| Stand pair | Listed height range | Build and lock | Fits well with |
|---|---|---|---|
| ESCO 3 Ton Performance Kit | 13.2 to 21.5 in. | Steel base, anodized post, pin | Cayenne, Macan, Panamera |
| BIG RED T42202 (2 ton) | 10-13/16 to 16-9/16 in. | Steel, ratchet | 911, Boxster, Cayman |
| GEARWRENCH GWJS2T (2 ton) | Not stated on listing | Ratchet, double lock pin | Sports cars, wheel and brake work |
| AUTOWN 3 Ton | 11 to 16.7 in. | Ratchet plus pin, flat saddle | Cars with flat pads under the sills |
| Omega 6 Ton | 16 to 23-1/2 in. | Ratchet, handle lock and pin | Cayenne and Panamera at full height |
If one garage holds a 911 and a Cayenne, a tall pair covers both, though you may need to lift the coupe higher before the stand fits. If you own only the sports car, a lighter pair with a lower starting height is easier to handle.

Cold Garage Habits for West Michigan Owners
Spring and fall wheel swaps in Grand Rapids tend to happen on a cold slab, sometimes with meltwater and salt tracked in from the street. A stand foot on a wet, gritty patch can creep as the load settles, so a few habits help.
- Sweep and dry the spot where each stand will sit, and avoid floor drains and expansion joints.
- Look over each support point for corrosion or a torn pad before trusting it with weight.
- Use the stands as a pair at matching heights, chock the wheels that stay down and set the parking brake.
- After lowering onto the stands, push firmly on the car before you reach underneath; it should not move.

When the wheels go back on, tighten the bolts with a calibrated wrench to the figure in your manual. Our torque wrench guide for Porsche wheels covers five-bolt hubs and center locks, and the starter list of car maintenance tools for beginners fills in the rest of a home kit.
When the Car Needs a Lift Instead
Stands are the right tool for a corner or one end at a time. Jobs that need all four wheels hanging, long reaches under the middle of the car, or a support point that looks cracked or rusted are safer on a two-post lift. Lowered cars can also run out of room for both a jack and a stand.

Our factory scheduled maintenance in Grand Rapids follows the owner’s manual checklist with the car on a lift. If you spotted a worn part while underneath, our suspension repair service and foreign car repair team can inspect it.
More Buying Guides
Frequently Asked Questions
What are the best jack stands for Porsche 911 owners?
A 3 ton pair with a flat or padded saddle and a starting height that fits under the car once one end is raised. The BIG RED T42202 and the GEARWRENCH GWJS2T are both 2 ton pairs that suit a 911 well.
Where do jack stands go on a Porsche?
Only at points your owner’s manual or workshop manual approves. Many owners lift at one approved point and set the stand at another, so the jack and stand never fight over the same pad.
Do I need rubber pads on my jack stands?
They help. A rubber flat top or a well-seated pad protects the factory support point and stops metal from sliding on metal. Make sure any pad sits firmly in the saddle and on the car.
Is a 2 ton pair enough for a Cayman?
For one end of a Cayman, Boxster or 911, a 2 ton pair has a wide margin. The rating is a ceiling, not a target, so a 3 ton pair is fine too. What matters more is the height range and the saddle shape.
Would you rather leave the lifting to a two-post lift? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a visit through our contact page.
Busy until after closing? Our after-hours drop-off is open to you, and the address is 456 Carrier St NE, Grand Rapids.
