As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A diesel Silverado or Sierra HD that nods at every expansion joint, or dives hard when a trailer pushes against the brakes, has usually worn through its dampers. The best shocks for Duramax pickups depend less on the engine than on the chassis under it and on how high the front end sits.
This guide sorts six listings for 2500HD and 3500HD trucks by generation, corner and ride height. For cars and lighter vehicles, our roundup of shocks and struts for daily drivers is the better starting point.
Quick answer
Which shocks suit a Duramax Silverado or Sierra HD?
Start with the chassis years and front height. A stock 2001 to 2010 truck, LBZ included, takes a Bilstein 4600 set. A stock 2011 to 2019 2500HD can run a Rancho RS5000X set, and a truck leveled about 1.5 inches up front needs longer Bilstein 5100 front shocks.
Our Quick Picks
Three quick picks: a Bilstein 4600 set for stock 2001 to 2010 trucks (LBZ era), a Rancho RS5000X set for a stock 2011 to 2019 Silverado 2500 HD and Bilstein 5100 fronts for a leveled 2011 to 2025 HD. All six listings are reviewed below.

Bilstein B6 4600 Set (2001-2010 HD)
A full four-corner refresh for the older HD chassis at factory height.

Rancho RS5000X Set (2011-2019 Silverado 2500 HD)
Four RS5000X shocks that bolt in with the factory mounting bolts.

Bilstein B8 5100 Front Pair (1.5" lift)
Longer front shocks for a nose raised with torsion keys or a leveling kit.
Why a Duramax Truck Is Hard on Its Front Shocks
Every Duramax HD from 2001 onward uses independent front suspension held up by torsion bars, with a separate shock at each front wheel. The rear is a solid axle on leaf springs, again with a plain shock at each corner. There are no struts anywhere on these trucks, so a shock swap never involves compressing a coil spring.
The diesel and its Allison transmission put more weight over the front axle than the gas engines do. Add a plow frame, a fifth-wheel hitch or a heavy trailer tongue, and front shocks on a working diesel often fade before the rears.
Reading a Listing: Chassis Years and Ride Height
Shock makers rarely mention the engine. An LB7, LLY, LBZ or LMM truck shares its shocks with gas HD trucks from the same 2001 to 2010 chassis, and LML and L5P trucks fall into the 2011 and later listings.
Ride height matters just as much. Many diesel owners turn the factory torsion keys up to level the nose, and Rancho explains in its guide to leveling Silverado and Sierra trucks that this removes droop travel and can top out and damage stock-length shocks. If your front end has been raised, buy a shock listed for that lift height.
Best Shocks for Duramax Trucks, Listing by Listing
Each pick below names its chassis years, corners and ride height, and some cover only one axle. Confirm the year, model, cab, drive type and engine in Amazon’s fit checker before you order.
1. Bilstein B6 4600: Front and Rear Shock Set for 2001-2010 Silverado/Sierra 2500/3500 HD at Stock Height

- Listed for 2001-2010 Silverado/Sierra 2500/3500 HD
- Four shocks for a 0" lift truck
- Velocity-sensitive digressive valving
- Vulcanized neoprene bushings
This Bilstein listing bundles four B6 4600 shocks, one for each corner, and names its fit as the 2001 to 2010 Chevrolet Silverado and GMC Sierra 2500 HD and 3500 HD with no lift. That span is the chassis behind the LB7, LLY, LBZ and LMM diesels, so it is the natural place to start for a stock-height truck from those years. Run your cab, bed, drive type and engine through Amazon’s fit checker before ordering, since the older 1999 to 2004 non-HD 2500 models use different parts.
The 4600 series uses digressive valving that responds to how fast the suspension moves, firming up for big, quick hits while staying fairly compliant over small ripples. Bilstein says each application is tuned through road testing for that vehicle, with the goal of steadier steering and control under changing loads. The bushings are vulcanized neoprene, and the set is covered by Bilstein’s limited lifetime warranty.
For a diesel that pulls a trailer or carries a camper, buying all four shocks at once keeps both axles damping evenly instead of pairing new fronts with tired rears. This set is built for factory ride height, so it is the wrong choice for a front end leveled with turned-up torsion keys or a lift kit.
View Bilstein B6 4600 Set (2001-2010 HD) on Amazon
2. Rancho RS5000X RS55377/RS55379: Four-Shock Set for 2011-2019 Silverado 2500 HD at Factory Height

- Listed for 2011-2019 Silverado 2500 HD
- Part numbers RS55377 and RS55379
- Fits 2WD and 4WD at 0" lift
- Mounting washers, bushings and nuts included
Rancho sells this RS5000X kit as a set of four for the 2011 to 2019 Chevrolet Silverado 2500 HD, listed for both two-wheel and four-wheel drive. The part numbers are RS55377 and RS55379, and the listing calls for a truck at factory height with no front or rear lift. That covers the LML years and the first L5P years, though Sierra owners should look for Rancho’s separate GMC listing and every buyer should confirm the cab and drive type in Amazon’s fit checker.
Each shock arrives with the washers, bushings and nuts needed for the job, and the factory mounting bolts are reused. Rancho backs the RS5000X line with a limited lifetime warranty against defects and premature failure. The maker also offers a 90 day ride guarantee on RS5000X, RS7000MT and RS9000XL shocks, so you have time to judge the feel on your own roads.
This set suits an owner who wants a straightforward replacement for worn factory shocks on a truck that is used for work, towing and daily driving. Because it is meant for stock height, it is not the pick for a Silverado leveled with torsion keys. Owners chasing a firmer monotube feel may prefer one of the Bilstein or FOX options below.
View Rancho RS5000X Set (2011-2019 Silverado 2500 HD) on Amazon

3. Bilstein B8 5100: Front Shock Pair for 2011-2025 Silverado/Sierra 2500/3500 HD with 1.5″ Front Lift

- Listed for 2011-2025 Silverado/Sierra 2500/3500 HD
- Sized for a 1.5" front lift
- Digressive valving
- Zinc-plated body for corrosion protection
This is a pair of front B8 5100 shocks for the 2011 to 2025 Chevrolet Silverado and GMC Sierra 2500 HD and 3500 HD, and the listing sizes them for a truck with a 1.5 inch front lift. That makes them a fit for the common diesel setup where the factory rake has been taken out by turning the torsion keys or adding a leveling kit. Only the fronts are included, so plan the rear shocks separately and confirm your exact truck in Amazon’s fit checker.
The 5100 uses the same velocity-sensitive digressive valving idea as Bilstein’s other truck shocks, with tuning the maker says comes from real-world testing on each vehicle. A zinc-plated finish protects the body against rust and road salt, which matters on a truck that spends winter on treated Michigan roads. Bilstein covers the 5100 series with a limited lifetime warranty.
The extra length lets the front suspension keep its travel after a mild lift, instead of topping out a stock shock on rebound. These are a sensible pick for an LML or L5P truck that has been leveled a little and still tows. They are not meant for a truck at factory height or one lifted well beyond 1.5 inches.
View Bilstein B8 5100 Front Pair (1.5" lift) on Amazon
4. FOX 2.0 Performance 980-24-664/980-24-963: Four-Shock Set for 2011-2019 Silverado 3500 HD with 0-1″ Lift

- Listed for 2011-2019 Silverado 3500 HD
- Part numbers 980-24-664 and 980-24-963
- Four shocks for 0-1" front and rear lift
- Washers, bushings, reservoir clamps and nuts included
This FOX kit pairs part numbers 980-24-664 and 980-24-963 into a set of four 2.0 Performance shocks for the 2011 to 2019 Chevrolet Silverado 3500 HD. The listing covers both two-wheel and four-wheel drive trucks at factory height or with up to 1 inch of lift front and rear. Because 3500 HD trucks come in single and dual rear wheel versions, check your configuration and engine carefully in Amazon’s fit checker.
The kit includes the washers, bushings, reservoir clamps and nuts, and it reuses the factory shock mounting bolts. Shock boots, roost shields and mounting plates are sold separately, so read the fit notes in case your truck needs plates. FOX covers these shocks with a limited one year warranty against defects and premature failure, which is shorter than the lifetime coverage several rivals offer.
The 2.0 Performance line is aimed at owners who want a more controlled, planted feel than a basic replacement gives, which can help a one-ton diesel carrying a heavy camper or hitch load. It suits a truck kept near stock height. For a 2500 HD or a truck with a bigger lift, look for the FOX listing that names that exact setup.
View FOX 2.0 Performance Set (2011-2019 Silverado 3500 HD) on Amazon

5. Rough Country V2: Monotube Front Shock Pair for 2011-2025 Silverado/Sierra 2500HD/3500HD with 0-2″ Lift

- Listed for 2011-2025 Silverado/Sierra 2500HD/3500HD
- Works from 0 to 2" of front lift
- 46mm piston with internal floating piston
- Brushed T6061 aluminum body
Rough Country sells this V2 pair for the front of the 2011 to 2025 Chevrolet Silverado and GMC Sierra 2500HD and 3500HD, with a listed range of zero to 2 inches of lift. That window suits a diesel owner who is running stock height now but may level the front later. Only the two front shocks are in the box, and you should still confirm your year, cab and drive type in Amazon’s fit checker.
Inside is a 46mm high-flow piston paired with an internal floating piston, which keeps the nitrogen charge separate from the oil in this monotube design. The shock mounts inverted, and the body is brushed T6061 aluminum rated at 36kN tensile strength. Rough Country backs the V2 line with its limited lifetime replacement warranty.
The wide height range is the main appeal, since one set of front shocks can stay on the truck through a modest leveling job. These suit owners who want a monotube front end without committing to a single lift height. Plan your own rear shocks to match, and skip this pair if your truck carries a lift taller than 2 inches.
View Rough Country V2 Front Pair on Amazon
6. Bilstein B6 4600: Rear Shock Pair for 2011-2025 Silverado/Sierra 2500/3500 HD at Stock Rear Height

- Listed for 2011-2025 Silverado/Sierra 2500/3500 HD
- Rear pair for a 0" rear lift
- Digressive valving
- Vulcanized neoprene bushings
This listing is a pair of rear B6 4600 shocks for the 2011 to 2025 Chevrolet Silverado and GMC Sierra 2500 HD and 3500 HD with no rear lift. It spans the LML years and both L5P generations, including the redesigned 2020 and later trucks. Since a leveled HD usually keeps its rear at stock height, this pair also works as the back half behind the lifted front shocks above, once you confirm the fit in Amazon’s fit checker.
The rear shocks use the same digressive valving as the rest of the 4600 range, reacting to quick suspension movement while keeping small bumps from feeling harsh. Bilstein says the tuning is set through road testing for each application, aimed at steady handling under varying loads. Neoprene bushings and a limited lifetime warranty round out the package.
The rear shocks on a diesel HD control the leaf springs under a fifth-wheel hitch, a gooseneck ball or a bed full of gear, so tired rears show up as a pogo motion with a trailer connected. This pair suits owners replacing only the rear axle or mixing brands front to rear. It is not for trucks with a rear lift or add-a-leaf.
View Bilstein B6 4600 Rear Pair (2011-2025 HD) on Amazon
Pick by Truck Generation and Front Height
Use this table to narrow the best shocks for Duramax trucks to the listing that matches yours, then check it against your VIN.
| Your Duramax truck | Listing to check | Corners and height | Watch for |
|---|---|---|---|
| 2001 to 2010 HD, stock (LBZ era) | Bilstein B6 4600 set | All four, 0″ lift | Not for 1999 to 2004 non-HD 2500s |
| 2011 to 2019 Silverado 2500 HD, stock | Rancho RS5000X set | All four, 0″ lift | Sierra uses its own listing |
| 2011 to 2025 HD, leveled front | Bilstein B8 5100 front pair | Front, 1.5″ lift | Rears bought separately |
| 2011 to 2019 Silverado 3500 HD | FOX 2.0 Performance set | All four, 0-1″ lift | Boots and mounting plates extra |
| 2011 to 2025 HD, mild front lift | Rough Country V2 front pair | Front, 0-2″ lift | Mounts inverted |
| 2011 to 2025 HD, stock rear | Bilstein B6 4600 rear pair | Rear, 0″ lift | Front pair is a separate listing |

Not every clunk from a diesel front end is a shock. Worn sway bar links, dry bushings and tired idler arms can all knock or creak, and our guide to why a car squeaks when going over bumps helps you sort the noises before you spend money on dampers.
Salt, Snowplows and Fifth Wheels in West Michigan
A diesel HD in Grand Rapids often works through the winter with a plow hung on the front, then tows a camper or boat all summer. The spring thaw then adds a fresh crop of potholes.
Look for a nose that keeps bobbing after a dip, a trailer that rocks the truck at highway speed, cupped front tires and shock bodies coated in wet grime. Those signs apply to shocks and struts alike, and our checklist on how to tell if struts are bad walks through the bounce test and the visual checks.

Road salt also attacks the mounting hardware. Lower shock bolts on a Michigan truck can seize into their sleeves, so spray them with penetrating oil the day before and keep a replacement bolt on hand in case one snaps.
Replacing Shocks Yourself or at a Shop
Shocks on these trucks are bolt-on parts, so the job suits a driveway with jack stands rated for heavy trucks.
Swapping shocks at the same ride height does not change the alignment. Turning the torsion keys or adding a leveling kit does, so book an alignment after any height change. Whichever of the best shocks for Duramax trucks you fit, replace them in axle pairs so both sides damp the same.

Rusted bolts, a plow frame in the way or a front end that clunks for no clear reason are good reasons to hand the job off. Our suspension repair service in Grand Rapids handles shocks, steering linkage and the parts around them. Steering and suspension is one of the areas where owner Hendrick Hoffman holds both ASE and State of Michigan certification, as our about us page explains.
More Buying Guides
Frequently Asked Questions
Do Duramax trucks take different shocks from gas HD trucks?
Usually not. Shock fit follows the chassis years, cab, drive type and ride height, so a diesel and a gas truck from the same generation often share parts. Still enter your engine in Amazon’s fit checker, because a few listings carry extra notes.
What shocks fit an LBZ Duramax truck?
The LBZ was offered in 2006 and 2007 HD trucks, which sit on the 2001 to 2010 chassis. Look for listings that name 2001 to 2010 Silverado or Sierra 2500HD or 3500HD at your ride height.
Do I need longer shocks after cranking the torsion keys?
If you raised the front more than a little, yes. Stock-length shocks can top out on a leveled truck, so choose a front shock listed for your lift height.
Do I need an alignment after replacing Duramax shocks?
Not if the ride height stays the same, since shocks do not set the wheel angles. Any change to the torsion keys or a leveling kit does call for an alignment.
Is your diesel pickup porpoising down the road or knocking through Grand Rapids potholes? Ring 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or request a suspension check on our contact page.
If the truck is out working all day, bring it to 456 Carrier St NE, Grand Rapids, MI 49505 after we close and use the after-hours drop-off.
