As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A loaded minivan puts more weight on its front struts than most sedans ever will, so a tired Sienna tends to tell you about it with a wallowing nose, a slow second bounce after dips and a knock from the front over broken pavement. Choosing the best struts for Sienna vans starts with three facts about yours: the model year, whether it is front or all-wheel drive, and how many seats it has.
Below are six listings for 2007 to 2025 vans, from complete corners to a bare damper. Not sure the struts are the culprit? Start with our walkthrough on how to tell if struts are bad.
Quick answer
Which struts suit a Toyota Sienna?
Pick by generation and drive type. A 2015 to 2020 front-drive van gets a full refresh from the Monroe 1000117VK kit, a 2011 to 2014 van suits the loaded Monroe 172781 corner, and a 2007 to 2010 front-drive van fits the Gabriel G57666. Keeping healthy springs? The bare KYB Excel-G 339293 is the damper-only route.
Our Quick Picks
Three quick picks: a four-corner Monroe kit for 2015 to 2020 front-drive vans, a loaded Monroe corner for 2011 to 2014 vans and a Gabriel ReadyMount for 2007 to 2010 front-drive vans. All six listings are reviewed below.

Monroe 1000117VK Kit
Both front corners and both rear shocks from one brand in one order.

Monroe Quick-Strut 172781
A bolt-in corner that renews the spring, mount and damper together.

Gabriel ReadyMount G57666
A ready-to-bolt front corner for the 3.5L second-generation van.
Four Sienna Generations, Many Strut Variants
Every Sienna from 2004 on has a strut at each front wheel, with rear shocks through 2020. The part still changes inside each generation, because the front corners vary by drive layout, engine and seating load.
- 2004 to 2010: the 3.3L V6 vans of 2004 to 2006 and the 3.5L vans of 2007 to 2010 use different front assemblies, and AWD vans have their own parts again.
- 2011 to 2014: the 2.7L four-cylinder and 3.5L V6 vans take separate struts, with FWD and AWD split as well.
- 2015 to 2020: the SE has its own sport-tuned front end, so many listings for this run say “without SE” in the title.
- 2021 to 2025: the hybrid-only van on the TNGA-K platform, with its own front struts and a multi-link rear.
Seating matters too. Several sellers mark a loaded strut “7 passenger only” or “8 passenger only,” because the coil spring is rated for a different front load. Count your seats, then enter year, trim, drive type and engine in Amazon’s fit checker.
Complete Corner or Damper Only for a Heavy Van
A complete corner, called a Quick-Strut by Monroe and a ReadyMount by Gabriel, ships with the coil spring, top mount, bearing plate and dust boot already on the damper. On a high-mileage Sienna that matters, since sagging springs and cracked mounts are common by the time the dampers fade, and the whole lot gets replaced in one visit.
A bare strut means moving the old spring across under compression, which needs a proper tool and care; our roundup of coil spring compressors for strut jobs explains the safe types. Go bare only when the springs still hold factory height and the mounts are quiet.
Best Struts for Sienna Vans: Six Listings in Detail
Each listing below names the model years, drive type and position it covers, and some are sold one corner at a time. Confirm year, model, engine, drive type and side on Amazon before you buy, because no single listing fits every Sienna.
1. Monroe 1000117VK: Front Quick-Strut and Rear OESpectrum Shock Set for 2015-2020 Sienna FWD

- Listed for 2015-2020 Toyota Sienna FWD
- Two front Quick-Strut assemblies
- Two rear OESpectrum shocks
- Mounting hardware included
The Monroe 1000117VK is a four-piece set listed for the 2015 to 2020 Sienna with front-wheel drive. It bundles two front Quick-Strut assemblies with two rear OESpectrum shock absorbers, so one box covers every damper on the van. AWD vans are not part of the listing, and Monroe still asks owners to run the part finder, so enter year, trim and engine on Amazon before ordering.
Each front Quick-Strut comes fully assembled with the coil spring, upper mount and damper, which removes the need to compress a spring at home. Monroe states the springs meet or exceed the original spring performance, and the rear OESpectrum shocks use a self-lubricating seal to cut friction on the piston rod. Hardware for the install is included, which saves a parts store run halfway through the job.
The kit makes the most sense on a van past roughly 100,000 miles where the fronts and rears have aged together. Doing all four corners at once keeps the front and rear damping balanced, so the van settles evenly after dips instead of nodding at one end. It is not intended for lifting, lowering or a firmer setup, and owners with an SE should confirm the fit notes first.
View Monroe 1000117VK Kit on Amazon
2. Monroe Quick-Strut 172781: Loaded Front Strut and Coil Spring Assembly for 2011-2014 Sienna

- Listed for 2011-2014 Toyota Sienna
- Strut, spring and upper mount preassembled
- No spring compressor needed
- Protective coating, salt spray tested
The Monroe 172781 is a single loaded front corner listed for the 2011 to 2014 Sienna. It replaces KYB SR4415 in the cross-reference, and Monroe sells 172782 as its opposite-side partner, so plan on ordering both. This generation split its struts by engine, drive type and seating, so enter the full details on Amazon and read any blue qualifier notes before you check out.
The assembly arrives with the strut, an application-specific coil spring and a premium upper mount already joined. Monroe says the spring is calibrated to bring back the original ride height, and that the new mount restores steering precision while cutting noise and memory steer. The metal carries a protective coating that Monroe checks with salt spray testing, a sensible detail for a van that spends winters on treated roads.
Because the spring and mount are new, this corner fixes more than a weak damper. It suits an owner whose van sits lower at the front than it used to, clunks over railroad crossings or creaks when the wheel is turned at parking speed. Owners who want a sportier feel or a raised stance should look elsewhere, since the goal here is factory behavior.
View Monroe Quick-Strut 172781 on Amazon

3. Gabriel Ultra ReadyMount G57666: Front Right Complete Strut Assembly for 2007-2010 Sienna FWD

- Listed for 2007-2010 Toyota Sienna FWD
- Front right position, one assembly
- Pre-assembled, no spring compression
- Stroke 6.62 in, extended length 23.27 in
The Gabriel G57666 is an Ultra ReadyMount assembly for the front right corner of a 2007 to 2010 Sienna with front-wheel drive. The left side is a separate listing, so buy the pair and fit them in the same session. AWD vans of these years use different Gabriel numbers, which is one reason to confirm year, drive type and side on Amazon before purchase.
The listing gives useful specifications: a stroke of 6.62 inches, an extended length of 23.27 inches and the upper and lower mount codes. It also prints interchange numbers, including Monroe RoadMatic 182363 and KYB SR4154, which helps if you are matching an old part from the van or comparing brands. The strut, spring and mount arrive assembled, so there is no spring compression involved.
Second-generation vans are now old enough that the original springs and top mounts have usually lost some height and gained some noise. Swapping in a complete corner deals with all three wear items at once, which tends to work out simpler than chasing them separately. This assembly is aimed at restoring the original ride for family use, not at heavy towing or a modified ride height.
View Gabriel ReadyMount G57666 on Amazon
4. PM Auto Front Quick Complete Strut-Spring Pair: Left and Right for 2015-2020 Sienna FWD

- Listed for 2015-2020 Toyota Sienna FWD
- Front left and right in one pair
- Strut and coil spring preassembled
- Excludes the SE sport trim
The PM Auto pair covers both front corners of a 2015 to 2020 Sienna with front-wheel drive and the 3.5L V6. The listing names the L, LE, XLE and Limited trims, adds the XLE Premium and Limited Premium for 2018 to 2020, and leaves out the SE with its sport-tuned suspension. Some fitment lines mention 7-passenger seating, so read the notes closely and confirm year, trim and seating on Amazon.
Each corner arrives as a quick complete strut with the coil spring already fitted, which means no spring compressor in the driveway. Getting both sides in one box also removes the risk of ordering a mismatched left and right. The seller’s description is brief, so the fitment notes and the vehicle tool at the top of the listing carry most of the useful detail.
This pair suits an owner whose rear shocks are still in decent shape and who only needs to sort out a floating or clunking front end. It is a practical choice for a van that sees school runs and highway trips rather than heavy loads. Pair it with fresh rear shocks if they have covered the same miles, and book an alignment afterward.
View PM Auto Front Strut Pair on Amazon

5. KYB Excel-G 339293: Bare Front Gas Strut for Toyota Sienna

- Calibrated for the Toyota Sienna
- Bare strut, reuse your spring and mount
- Teflon-banded piston, seamless cylinder
- Triple chrome-plated piston rod
The KYB 339293 is an Excel-G gas strut sold as a bare damper for the front of the Toyota Sienna. Its listing cross-references Toyota part numbers 4852009S70 and 4852009S90 and Monroe 72782, which Monroe lists for 2011 to 2015 vans. KYB sells 339292 for the opposite side, and because the title names only the model, check year, drive type and side carefully on Amazon.
KYB describes the strut as calibrated to restore the van’s original handling. Inside, a seamless working cylinder and a Teflon-coated piston band help keep the seal tight, while a triple chrome-plated rod and multi-lip oil seals are meant to reduce wear. A sintered iron rod guide helps hold the strut straight, which supports correct alignment over time.
Going bare means removing the old assembly, compressing the spring and moving it, the mount and the bearing plate onto the new strut. That suits an owner who already has the right tool and whose springs still hold height, since only the damper gets renewed. If the mounts creak or the van sits low, a complete corner is usually the better fit for the job.
View KYB Excel-G 339293 on Amazon
6. MAC Front Complete Struts with Coil Springs: Pair for 2021-2025 Sienna

- Listed for the 2021-2025 Toyota Sienna
- Front pair with coil springs
- Built to meet or exceed OE specification
- ISO certified factory production
This MAC pair is one of the few complete front strut listings for the fourth-generation, hybrid-only Sienna. The title lists the 2021, 2022, 2023 and 2025 model years, so 2024 owners need to confirm fitment with the vehicle tool, and every buyer should check trim and drive type. MAC sells a separate XSE version, which suggests the sportier trim takes its own part.
Each strut comes assembled with its coil spring, so the pair bolts in without spring compression. The seller states the parts are made in ISO certified factories and designed to meet or exceed original specifications, and that each one is inspected for workmanship. The listing is light on technical data, so read the product details section for the exact year and model coverage.
Most 2021 and newer vans are still young, but high-mileage rideshare and fleet vans can wear their front struts sooner. This pair suits an owner whose van is past its factory coverage and who wants a straightforward front-end refresh. Anyone with remaining warranty should speak to the dealer first, and anyone unsure about the fit should send the VIN to the seller.
View MAC Front Strut Pair on Amazon
Sienna Strut Fit Table
Use the table to narrow the best struts for Sienna vans down to one listing, then match the part number against your VIN.
| Your Sienna | Listing to check | Type | Watch for |
|---|---|---|---|
| 2015 to 2020 FWD, all four corners worn | Monroe 1000117VK kit | Front loaded struts plus rear shocks | Not for AWD vans |
| 2015 to 2020 FWD, front only | PM Auto front pair | Loaded pair | Excludes the SE |
| 2011 to 2014 | Monroe Quick-Strut 172781 | Loaded, one corner | Order 172782 for the other side |
| 2011 to 2015, springs still good | KYB Excel-G 339293 | Bare strut, one side | Needs a spring compressor |
| 2007 to 2010 FWD | Gabriel ReadyMount G57666 | Loaded, front right | Left side sold separately |
| 2021 to 2025 hybrid | MAC front pair | Loaded pair | 2024 missing from the title |
A noise over speed bumps does not always mean a failed strut. Squeaks and creaks often trace back to sway bar bushings, end links or a dry ball joint, and our article on why a car squeaks when going over bumps walks through the likely sources.

How West Michigan Roads Wear a Family Van
A Sienna in Grand Rapids spends winters on salted streets with freeze-thaw potholes, often fully loaded. That works the front struts hard, and because the van rides softly, drivers rarely notice the decline.
Watch for the nose dipping hard at stop signs, the body swaying in highway crosswinds and scalloped wear on the front tires. A clunk from the top of the strut on cold mornings usually points to a worn mount, which is one more reason a complete corner makes sense on older vans.

Road salt also seizes the lower strut bolts and the top nuts over several winters. Spray them with penetrating oil the night before and have new hardware on hand.
Driveway Swap or a Shop Visit
With complete corners, a front strut change on a Sienna is a fair home job for someone who owns a good jack, stands, a breaker bar and a torque wrench.
Whichever of the best struts for Sienna vans you fit, schedule an alignment afterward. Pulling a strut shifts camber and toe, and a heavy van left out of spec chews through the inner tire edges quickly. Toyota’s 2021 Sienna launch release details the TNGA-K platform and multi-link rear of the newest van, which helps explain why its parts share nothing with older generations.

Prefer to hand the van over? Our Grand Rapids suspension repair service handles struts, top mounts, sway bar links and the steering parts that wear alongside them.
Hendrick Hoffman, who owns the shop and runs the bays, holds ASE and State of Michigan certifications covering steering and suspension, as our about us page explains. Shopping for a second car? Our wider guide to shocks and struts for daily drivers covers sedans and crossovers.
More Buying Guides
Frequently Asked Questions
Do 7-passenger and 8-passenger Siennas take the same struts?
Not always. When shopping for the best struts for Sienna vans, note that many loaded listings are rated for one seating layout because the coil spring carries a different front load, so check the seat count against the listing notes.
Does an AWD Sienna need different struts?
Yes, on most years. Brands such as Gabriel, KYB and PM Auto sell separate AWD versions, so choose a listing that names your drive type.
Should the rear shocks be replaced along with the front struts?
If they have covered the same miles, it is usually worth it. New fronts with worn rears can leave the back of the van bouncing after dips, which is why kits like the Monroe 1000117VK include both.
Is an alignment needed after a Sienna strut job?
Yes. Removing the strut disturbs the front geometry, and an alignment keeps the van tracking straight and protects the tires.
Is your Sienna floating, diving or knocking on Grand Rapids streets? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or request a suspension check through our contact page.
School runs fill your daytime hours? The after-hours drop-off means the van can come to 456 Carrier St NE once your evening is free.
