As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
Stand in front of the spark plug rack at any parts counter and the Denso vs AC Delco choice shows up fast. Both brands sell iridium plugs that look almost identical in the package, both supply carmakers straight from the factory, and both have loyal fans on every forum. The useful question is not which logo wins, but which plug your engine was designed around.
This guide explains where each brand comes from, then compares three current iridium plugs: the Denso Iridium TT 4702 (IK20TT), its Iridium Power sibling the Denso 5304 (IK20), and the ACDelco GM Original Equipment 41-162. If you are still deciding whether your plugs are due at all, start with our guide on how often to change spark plugs and the signs they are worn.
Quick answer
Should you put Denso or ACDelco plugs in your engine?
Use the brand and part number your engine maker specifies. ACDelco 41-series iridium plugs are GM’s original equipment line for Chevrolet, Buick, GMC and Cadillac engines. Denso supplies many Japanese engines, and its Iridium TT pairs a 0.4mm iridium tip with a platinum ground. Both are quality plugs when the part number matches.
Our Quick Picks
Two Denso iridium plugs that share the IK20 heat code and one ACDelco original equipment plug, each sold through the maker's own Amazon listing. All three are reviewed in full below.

Denso Iridium TT 4702
Twin-tip iridium and platinum plug that crosses over to many engines.

ACDelco 41-162
The factory part for the GM engines that call for this number.

Denso Iridium Power 5304
Same IK20 heat code, with a grooved ground strap in place of a needle.
Two Plug Makers With Factory Roots
ACDelco is the parts brand of General Motors. Its GM Original Equipment plugs are the ones GM engineers design and validate for their own engines, and the listing notes that some of them were once sold under the GM Genuine Parts or ACDelco Professional names. If you drive a Silverado, an Equinox or an older Buick, the plug that came out of your engine very likely had an ACDelco number on it.
Denso is a large Japanese supplier that makes everything from A/C compressors to ignition coils. Its plugs are factory fit in many Toyota and other Japanese engines, and Denso says its Twin-Tip design first appeared on original equipment plugs for luxury and performance cars. In the aftermarket, Denso sells several families, from Iridium Long Life to Iridium Power and the Iridium TT.
So each brand is the home team for a different set of engines. That fact matters more than any spec sheet, because a plug’s reach, seat, heat range and gap are all chosen for one combustion chamber. A well-made plug in the wrong application can still misfire.
Denso vs AC Delco: Plug Specs Side by Side
The figures below come from the three Amazon US listings and Denso’s own product page. Where a maker states nothing, the table says so rather than guessing.
| Point | Denso Iridium TT 4702 (IK20TT) | ACDelco 41-162 (19417055) | Denso Iridium Power 5304 (IK20) |
|---|---|---|---|
| Center electrode | 0.4mm iridium | Iridium, size not listed | 0.4mm iridium |
| Ground electrode | 0.7mm platinum needle | Not described in the listing | U-groove, taper cut |
| Preset gap | .039 in (1.0mm) on Denso’s multi-pack listing | Not listed; use GM’s spec | Not listed; measure before fitting |
| Seal | Not described in the listing | Three-piece fired-in suppressor seal | Not described in the listing |
| Fitment basis | Cross-references a long list of OE numbers | Exact replacement for GM engines that use it | Shares much of the 4702’s OE list |
| Life claim | Denso: alloy resists wear for over 100,000 miles | Wear resistance stated, no mileage | No mileage given |
The headline difference is philosophy. Denso built the Iridium TT as a wide-coverage upgrade plug that crosses over to many engines, while the ACDelco 41-162 is a direct factory replacement for the specific GM engines that call for that number.
Denso vs AC Delco Spark Plugs: The Three Plugs in Detail
We chose two Denso iridium plugs from different families and one ACDelco factory plug. Spark plugs are engine-specific, so treat these listings as examples of each line and confirm the exact part number with Amazon’s fit checker or the maker’s catalog before you order.
Denso 4702 IK20TT Iridium TT: Twin-Tip Spark Plug with 0.4mm Iridium Center

- 0.4mm iridium center electrode
- 0.7mm platinum needle ground electrode
- Twin-Tip design for a less obstructed spark
- Cross-references a long list of OE numbers
The 4702, also coded IK20TT, is one of the most widely listed plugs in Denso’s Iridium TT family. It is sold here as a single plug, so a four-cylinder engine needs four and a V6 needs six. The listing shows a long string of original equipment numbers it replaces, which tells you Denso designed it as a crossover plug for many engines rather than one exact factory fit.
Its main idea is the Twin-Tip layout. A 0.4mm iridium center electrode faces a 0.7mm platinum needle ground electrode, and Denso says the two fine tips leave less metal in the way of the spark, so the flame can grow in every direction. Denso also states that its iridium alloy resists wear for over 100,000 miles, and its multi-pack listing of the same plug gives a preset gap of .039 inch, or 1.0mm.
The 4702 makes sense when Denso’s parts finder or Amazon’s fit checker lists it for your exact year, engine and trim. Check the gap against your service information before you install it, and handle the fine tip with care. It is not the answer for an engine whose maker calls for a different heat range or a specific factory plug, so do not buy it on the strength of the twin-tip design alone.
View Denso Iridium TT 4702 on Amazon

ACDelco 41-162 (19417055) Iridium: GM Original Equipment Spark Plug

- GM Original Equipment iridium plug
- Exact replacement for the original part
- Three-piece fired-in suppressor seal
- Designed and validated by GM engineers
The 41-162 carries GM part number 19417055 and belongs to ACDelco’s GM Original Equipment range. The listing describes it as an exact replacement for the original component, and it says GM engineers design and validate these parts for Chevrolet, Buick, GMC and Cadillac vehicles. Some parts in the range were once sold as GM Genuine Parts or ACDelco Professional, so an older box with a different label can hold the same plug.
The plug uses an iridium electrode, which the listing credits with a high melting point and the strength to resist wear. ACDelco lists steady idle, reliable cold starting, quick acceleration and smooth running as the benefits. A three-piece fired-in suppressor seal meters spark energy for long electrode life, helps prevent combustion leakage and helps block radio interference that can upset the vehicle’s electronics.
The listing does not give a gap or a vehicle list, so confirm with Amazon’s fit checker or a GM parts catalog that your engine uses 41-162, then check the gap against GM’s spec. On a GM engine that calls for this number, it is the most direct way to put back what the factory installed. It does not suit non-GM engines, and its iridium design will not cure a misfire caused by a coil or injector.
Denso 5304 IK20 Iridium Power: Spark Plug with U-Groove Ground Electrode

- 0.4mm iridium center electrode
- U-groove and taper cut ground electrode
- Patented 360 degree laser-welded center tip
- Shares many OE cross-references with the 4702
Coded IK20, the 5304 belongs to Denso’s Iridium Power line and carries the same IK20 heat code as the twin-tip 4702 above. It also comes as a single plug, and its listing opens with many of the same original equipment numbers, including 12610767 and 1822A002, so Denso offers the pair as alternatives across much of the same engine coverage.
The split between them is on the ground side. Rather than a platinum needle, the Iridium Power uses a U-groove and taper cut ground electrode, which Denso credits with faster flame growth and less heat quenching. The center tip is the same 0.4mm iridium, joined to the electrode by a patented 360 degree laser weld that Denso says gives a strong, lasting bond.
Reach for the IK20 when Denso’s catalog lists it for your engine and you prefer a conventional ground strap over a fine platinum point. The listing gives no preset gap, so measure each plug before installing it. Like its twin-tip sibling, it is no stand-in for a GM engine that specifies the ACDelco 41-162, nor for an engine that needs another heat range.
View Denso Iridium Power 5304 on Amazon

Heat Range, Gap and Fit Explained
Heat range numbers do not cross brands
Heat range describes how quickly a plug sheds heat from its firing tip into the cylinder head. A plug that runs too hot can cause pre-ignition, and one that runs too cold can foul with carbon in short-trip driving. The “20” in Denso’s IK20TT is its heat code, and Denso’s own part numbering chart shows that the same heat range carries a different number at NGK, Champion and Bosch.
ACDelco’s 41-series numbers are catalog numbers rather than a readable heat scale. That means you cannot swap brands by matching digits. Use a cross-reference from the plug maker, or simply buy the number listed in your owner’s manual or parts catalog.

Gap: check it, but handle fine tips gently
The gap is the space the spark jumps between the center and ground electrodes. Denso’s multi-pack listing for the 4702 gives a preset gap of .039 inch (1.0mm), and the ACDelco listing gives none, so compare each plug against the gap in your service information. If a change is needed, use a wire-style gauge and bend only the ground strap, never pry against a fine iridium tip.
Original equipment fitment
Both brands publish catalogs that list plugs by year, make, model and engine. On a GM engine, the ACDelco number is the factory part, and on many Japanese engines the factory plug wears a Denso or NGK label. Denso’s Iridium TT product page explains the twin-tip design and links to its parts finder, which is a quick way to check whether a TT plug is offered for your engine at all.
Which Plug Suits Which Engine
Use the engine under your hood as the tiebreaker, not the price tag or the forum vote.
| Your situation | Better fit | Why |
|---|---|---|
| GM engine that shipped with ACDelco 41-162 | ACDelco 41-162 | Same part GM validated for that engine |
| Toyota or other engine with a Denso plug from the factory | Denso, matched by catalog | Keeps the original heat range and design |
| Engine where Denso lists the 4702 as a replacement | Denso Iridium TT 4702 | Twin-tip design with a 1.0mm preset gap |
| Engine where Denso lists the 5304 instead | Denso Iridium Power 5304 | Same heat code with a grooved ground strap |
| Any engine with a tuned or modified ignition | Ask a tuner or mechanic | Heat range may need to change |
| Unsure which plug is installed now | Pull one plug and read it | The number on the insulator tells you |
When both brands list a plug for your engine, either is a sound choice. Buy from the brand’s own Amazon listing rather than an unbranded bundle, and look over the box and plugs for consistent printing before installing them.
Cold Starts and Wet Roads in West Michigan
A Grand Rapids winter is hard on ignition parts. Cold, dense air and a rich cold-start mixture ask more of the spark, and a plug with a worn, rounded tip needs more voltage to fire. That extra demand lands on the ignition coils, which is why worn plugs and failing coils so often show up together in January.

Short winter trips also matter. An engine that never fully warms up leaves carbon on the insulator, and a plug that runs too cold for the engine fouls faster. Slush and road salt sprayed across the engine bay can work into worn coil boots, so check the boots for cracks and white tracking marks whenever the plugs come out.
A thin film of dielectric grease inside each boot helps keep moisture out. Whether the plug threads take anti-seize depends on the plug maker’s instructions, since many plugs have plated threads and torque specs that assume dry threads.
When a New Plug Will Not Fix It
Fresh plugs cure a misfire only when the old plugs were the cause. If the misfire stays after a plug change, the fault may sit in a coil, an injector, a vacuum leak or low compression. A blinking warning lamp is a serious sign, and our article on why a check engine light is flashing explains why you should ease off and get the car checked soon.

A hesitation under load that does not clear after new plugs is another clue that something else is wrong, and our guide to a car that hesitates when accelerating covers the usual suspects. Our shop handles check engine light diagnostics in Grand Rapids, reading the misfire counters and testing coils and injectors before any parts get replaced.
More Buying Guides
Frequently Asked Questions
Is Denso better than ACDelco?
Neither brand is better for every engine. ACDelco’s GM Original Equipment plugs are the factory parts for many Chevrolet, Buick, GMC and Cadillac engines, and Denso is factory fit on many Japanese engines. The better plug is the one whose part number your engine maker or the plug maker’s catalog lists.
Can I use Denso plugs in a GM engine?
Yes, if Denso’s catalog lists a plug for that exact engine. Match it through Denso’s parts finder rather than by copying digits from the old plug, because heat range numbers differ between brands. If no Denso listing exists for your engine, stay with the ACDelco part.
Do new iridium plugs need to be gapped?
Check the gap on every new plug against your engine’s spec, even when it comes preset. Denso lists a 1.0mm gap for the 4702 multi-pack. If you must adjust it, use a wire gauge and move only the ground strap so the fine iridium tip is not damaged.
Will new spark plugs turn off my check engine light?
Only if worn plugs caused the code. Misfire codes can also come from coils, injectors or vacuum leaks, and the light may need the code cleared or a few drive cycles to go out. If it returns or flashes after new plugs, have the system diagnosed.
Still chasing a misfire after a fresh set of plugs? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or schedule a check engine diagnosis online.
Can’t get away from work during the day? Leave the car with our after-hours drop-off and we’ll take it from there. We work out of 456 Carrier St NE in Creston.
