456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Which Front Hub for a Journey? Mevotech vs Moog Hub Assembly

mevotech vs moog hub assembly: scenic aerial view of a winding road through dense forest

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A Dodge Journey with a worn front bearing tends to announce it on the highway: a low drone that grows with speed and shifts when you lean into a long curve. Once the noise is pinned to a hub, the mevotech vs moog hub assembly question usually follows, since both brands sell a bolt-on unit for this crossover at similar money.

To keep things fair, every hub on this page is built to the same interchange number, 513286, the front position on the 2009-2020 Journey. MOOG supplies one version and Mevotech supplies two, so you can see how the brands and the tiers line up. If you drive something else, our list of wheel hub assembly brands with part numbers for other vehicles is the place to start.

Quick answer

Should a Dodge Journey get a Mevotech or a MOOG front hub?

Both fit the 513286 front position, so pick by features. MOOG names the Journey directly and lists a quad lip seal and rust-resistant hub. Mevotech’s TXF513286 adds coating on every surface plus hardware and torque specs in the box. Confirm fit, reuse the separate ABS sensor, and torque the axle nut to spec.

Our Quick Picks

One MOOG and one Mevotech TXF hub for the same 2009-2020 Journey front corner, plus Mevotech's Supreme H513286HW as the other tier of the same number. All three are covered in full below.

MOOG 513286 product photo
MOOG pick

MOOG 513286

Front hub, 513286, Journey named

A sealed DRiV hub whose listing names the Journey outright.

SuitsOwners who want the fit stated by vehicle
View on Amazon →
Mevotech TXF513286 product photo
Mevotech pick

Mevotech TXF513286

Front hub, 513286 position

Mevotech's upper tier, coated all over with bolts in the box.

SuitsJourneys that will see many more salted winters
View on Amazon →
Mevotech Supreme H513286HW product photo
Supreme tier

Mevotech Supreme H513286HW

Front hub kit, 513286 position

Mevotech's other tier for the same number, with hardware.

SuitsOwners who want bolts in the box without the top tier
View on Amazon →

Two Chassis Brands Behind One Part Number

Mevotech is a Toronto company that has sold steering, suspension and driveline parts since 1982. Its official site lists wheel hub assemblies next to control arms, ball joints and tie rods, and calls the company an engineering house first. The brand pitches its parts at professional technicians and leans on patented chassis designs.

MOOG is one of the brands of DRiV, the parts group named on its Amazon listings, and it is known mostly for steering and suspension work. On hubs, MOOG talks about sealing, coated studs and a quiet bearing more than about raw engineering claims. So you are comparing two chassis specialists here, not a bearing maker against a parts brand.

Owner chatter on forums is split. Some people describe a MOOG hub that let go early, others say the same about Mevotech, and a few insist the castings look identical. Those stories are worth reading but not worth deciding on, because nobody publishes failure data by brand.

What the front hub does on a Journey

On the Journey the front bearing comes as a sealed, bolt-on cartridge. The bearing, the five-stud wheel flange and the ring that the ABS sensor reads are all inside one unit, which bolts to the back of the steering knuckle while the front axle shaft slides through its splined center. When the bearing wears you swap the whole assembly, so no press is involved.

The wheel speed sensor itself is a separate part on this crossover, and none of the three listings below mentions one in the box. Look at how the sensor sits on your old hub before you start, so you know whether it lifts out cleanly or needs to be replaced along with it.

Mevotech vs Moog Hub Assembly by the Listing

The table lines up what each Amazon US listing actually states for the 513286 position. Only MOOG names the vehicle, while both Mevotech parts rely on the number itself. Any spec a listing leaves out is marked as not stated in the table.

PointMOOG 513286Mevotech TXF513286Mevotech H513286HW
How fit is shownNames the 2009-2020 JourneyPart number onlyPart number only
SealingQuad lip sealMulti-lip Advanced Quantum Sealing SystemMulti-point sealing system
CorrosionRust-resistant hub, secure studsRepel-TEK coating on every surfaceCoating on studs and hardware
In the boxHub kit, no hardware list givenFastening hardware and torque specsFastening hardware and torque specs
Lubricant namedNot statedNanoCeramic lubricantPremium grease
Mevotech and MOOG 513286 front hubs for the 2009-2020 Dodge Journey, compared from their Amazon US listings

On paper the TXF513286 lists the most features, the Supreme tier sits in the middle, and MOOG makes up ground by spelling out the fit. None of the three Amazon listings states a warranty term, so ask the seller what applies before you order.

Mevotech vs Moog Hub Assembly: Three Journey Hubs Up Close

All three hubs below fill the same front corner on either side of a 2009-2020 Journey. Run your VIN or year and trim through Amazon’s fit checker first, because a part number match is the only promise the Mevotech listings make about fit.

MOOG 513286: Front Wheel Bearing and Hub Assembly for 2009-2020 Dodge Journey with Quad Lip Seal

MOOG 513286 product photo
Key features
  • Listed for the 2009-2020 Dodge Journey
  • Sealed bearing built for a quiet ride
  • Quad lip seal against moisture and debris
  • Secure studs and a rust-resistant hub

The 513286 is MOOG’s front wheel bearing and hub assembly for the Dodge Journey, and its compatibility line covers every model year from 2009 to 2020. That makes it the only one of the three hubs here whose listing names the vehicle rather than leaning on a number alone. One general bullet on the page mentions Cadillac and Chevrolet models, which reads like shared copy, so trust the compatibility line and Amazon’s fit checker.

MOOG builds the unit around a sealed bearing assembly that it describes as noise free at highway speed. A quad lip seal is there to keep water and grit away from the rolling elements, which is where most hubs fail in salt country. The listing also points to secure studs and a rust-resistant hub, and it sells the part as an easy install hub kit, though it does not list bolts or torque figures in the box.

This hub suits a Journey owner who wants a well-known chassis brand and a plain statement of fit. It is a bolt-on cartridge, so no press is needed, but you will still move the wheel speed sensor across from the old hub. The listing gives no warranty term and sends questions to the seller, so ask before you buy.

View MOOG 513286 on Amazon

drone captures a stunning road slicing through lush green fields under a clear blue sky

Mevotech TXF513286: Wheel Bearing and Hub Assembly with Repel-TEK Coating and Install Hardware

Mevotech TXF513286 product photo
Key features
  • Higher grade rolling elements, optimized geometry
  • Multi-lip Advanced Quantum Sealing System
  • NanoCeramic lubricant fill
  • Repel-TEK coating, hardware and torque specs included

The TXF513286 is the upper of the two Mevotech hubs for this number. Its listing does not name a vehicle, so fit rests on the 513286 interchange, which catalogs place at the front of the 2009-2020 Journey. Put your VIN or year and trim into Amazon’s fit checker before ordering, since that is the only fit confirmation the page offers.

Mevotech says the internals use higher grade rolling elements with geometry tuned to cut rolling resistance and spread the load. Sealing comes from what it calls the Advanced Quantum Sealing System, a low-friction, multi-lip design meant to keep dirt out and grease in. The bearing is filled with a NanoCeramic lubricant that the maker says holds its viscosity through temperature swings. A Repel-TEK anti-corrosion coating covers every surface, including the studs and the supplied hardware.

That full coating is the main reason to pick this hub for a Journey that lives on brined Michigan roads. Fastening hardware and torque specs come in the box, so you are not reusing rusty bolts. The listing does not mention a wheel speed sensor, so plan to reuse the old one, and it gives no warranty term.

View Mevotech TXF513286 on Amazon

Mevotech Supreme H513286HW: Wheel Bearing and Hub Assembly Kit with Hardware and Coated Studs

Mevotech Supreme H513286HW product photo
Key features
  • Roll formed for a set preload out of the box
  • Fastening hardware and torque specs included
  • Anti-corrosion coating on studs and hardware
  • Multi-point seal and premium grease fill

The H513286HW is Mevotech’s Supreme kit for the same 513286 position, and the HW at the end of the number marks the version that comes with hardware. Like the TXF unit, its listing does not name a vehicle, so check fit for your Journey with Amazon’s fit checker before you buy. It serves as the closest alternative in this comparison, from the same maker but a different tier.

Mevotech says the hub is roll formed to lock the internal parts together, which sets the bearing preload at the factory and stiffens the assembly to reduce vibration. A multi-point sealing system keeps contaminants out, and the bearing is packed with a premium grease rated for heat and high pressure. The anti-corrosion coating is applied to the studs and hardware rather than to every surface of the hub.

This kit suits an owner who wants new bolts and printed torque figures but does not need the full coating of the TXF version. It is a sensible fit for a Journey that sees moderate winter use or will not be kept for many more years. The listing mentions no sensor and no warranty term, so check both with the seller.

View Mevotech Supreme H513286HW on Amazon

aerial view of a highway cutting through a forested landscape with moving vehicles and autumn foliage

Matching a Hub to the Way You Drive

Most Journey owners can settle this with two questions: how long you plan to keep the vehicle, and how hard the last hub fought you on the way out. The table is a starting point, and the right number always comes before the brand.

Your situationLeans towardWhy
You want the vehicle named on the listingMOOG 513286Compatibility line names the 2009-2020 Journey
Winters on brined roads, keeping it for yearsMevotech TXF513286Coating on every surface, including studs and hardware
You want new bolts and torque figures in the boxEither Mevotech tierBoth list hardware and torque specs
The other side has a good hub of one brandThat same brandKeeps both front corners on one design
High miles and both sides are hummingAny of the three, as a pairFresh bearings across the axle
Moog vs Mevotech wheel bearings matched to common Dodge Journey repair situations

If you only plan to keep the Journey a year or two, the price gap between tiers matters more than the extra coating. For an owner who expects to keep driving it through several more salt seasons, a hub that resists rust at the knuckle can save real effort the next time it comes apart.

captivating scenic view of a winding road through the lush green mountains and valleys of Tyrol

Bearing life depends more on the road and the install than on the label. Deep puddles, pothole hits and an axle nut left loose or overtightened all cut a bearing short, and our article on how long wheel bearings last and what wears them out goes through the causes. A correctly installed hub from either brand should last years under normal use.

Swapping a Journey Front Hub

The job itself is straightforward on a lift or good jack stands. Loosen the axle nut with the wheels on the ground, then remove the caliper, bracket and rotor, hang the caliper so the brake hose is not stretched, and unbolt the hub from the back of the knuckle. Take the wheel speed sensor out before the hub moves so the lead is not torn.

Torque the hub bolts and the axle nut to the figures in the service manual for your model year, using a torque wrench rather than an impact gun. Our guide to the torque wrench options for lug nuts and axle nuts covers the ranges you need. The Mevotech boxes include printed torque specs, which helps, but the manual is still the reference.

lone car travels on a winding road through Greece with mountains

Some cars use a bearing pressed into the knuckle instead of a bolt-on cartridge, and those jobs need a press or a receiver set. Our page on wheel bearing press kits for front-wheel-drive hubs explains the tools. The 513286 on the Journey does not need one.

Salt, Rust and a Stubborn Knuckle

West Michigan winters are hard on this joint. Brine works into the gap between the hub and the knuckle, and after a few seasons the bolts come out while the hub stays welded in place by rust. Soak the seam with penetrant ahead of time and expect to use a slide hammer or puller on an older Journey.

Clean the knuckle bore and mounting face back to bare metal before the new hub goes in. A thin film of anti-seize on the outer seat, kept clear of the sensor bore, will make the next removal far easier. A hub that seats on a ridge of scale can run with a slight wobble that wears the new bearing and the rotor early.

When We Should Take It From Here

Not certain the noise is a bearing? Cupped tires, a dragging caliper or a clicking CV joint can sound similar, and our article on the noises a failing wheel bearing makes helps you sort them out. A damaged sensor or tone ring can also bring on a warning light, which our guide to what an ABS light means explains.

idyllic country path lined with stone walls and lush flowers

A seized hub, a rounded axle nut or no safe way to support the crossover are all good reasons to hand the job over. We handle wheel bearing replacement in Grand Rapids on foreign and domestic vehicles, and check the CV axle, ball joints and brakes while the corner is open. Hendrick Hoffman holds ASE and State of Michigan certification in steering, suspension and brakes.

Frequently Asked Questions

Is Mevotech as good as MOOG for wheel hubs?

For the same part number the two are close, and neither brand publishes failure data that settles it. MOOG names the vehicle and lists a quad lip seal, while Mevotech’s TXF tier lists more coating and includes hardware. Pick the one whose features fit how you drive and how long you will keep the vehicle.

Does a 513286 hub come with the ABS sensor?

None of the three listings here mentions a sensor. On the Journey the wheel speed sensor is a separate part that reads a ring inside the hub, so plan to move your old sensor across or buy a new one if it is cracked or seized.

What is the difference between Mevotech Supreme and TXF hubs?

Going by the listings, both include hardware and torque specs. The TXF513286 adds upgraded rolling elements, a multi-lip sealing system, NanoCeramic lubricant and a coating on every surface, while the Supreme H513286HW coats the studs and hardware and uses a multi-point seal with premium grease.

Should I replace both front hubs on a Journey at once?

It is not required. On a high-mileage crossover the second side is often not far behind, though, and doing both at once saves a second teardown and keeps the front corners on one design.

Still hearing that hum from the front of your Journey? Phone 456 AutoFix at 616-279-3832 between 8am and 5pm, Monday to Friday, or ask for a hub and bearing check through our contact page.

Can’t get away from work while we’re open? Our after-hours drop-off at 456 Carrier St NE lets you leave the keys overnight, along with a note on which side is making noise.