456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Silverado, Equinox or Camaro: Choosing the Best Floor Jack for Chevy Owners

best floor jack for chevy: aerial shot of a foggy autumn forest

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

Chevrolet builds everything from a ground-hugging Camaro to a 4×4 Silverado that sits high on its frame. That spread is why the best floor jack for Chevy owners is rarely one size fits all: a jack that slides under a Malibu may run out of lift before a Silverado tire leaves the floor.

Below we split the lineup into model groups, explain the numbers printed on a jack and review six options. If your garage holds mostly cars, our low profile floor jack guide for cars goes deeper on low-entry designs.

Quick answer

What floor jack suits a Silverado, Equinox or Camaro?

A Silverado 1500, Tahoe or Suburban needs a 3-ton or larger jack that reaches about 20 inches, such as the Auto Dynasty 4-ton. An Equinox or Malibu suits the OEMTOOLS 24837. A Camaro or Corvette needs a low, long-reach frame like the AV Steel 2-ton.

Our Quick Picks

Three quick picks for the main Chevy groups: one all-rounder, one for full-size trucks and SUVs, and one for low cars. All six are reviewed below.

OEMTOOLS 24837 product photo
All-round pick

OEMTOOLS 24837

3.5 ton · 3-3/4 to 20-1/2 in · dual pump

Starts low enough for cars and climbs high enough for many trucks.

SuitsMixed Chevy garages: Malibu to Silverado
View on Amazon →
Auto Dynasty 4-Ton product photo
Trucks and big SUVs

Auto Dynasty 4-Ton

4 ton · 4.5 to 20 in · steel

Extra capacity margin for the heaviest Chevys you are likely to lift at home.

SuitsSilverado 1500, Tahoe, Suburban
View on Amazon →
AV Steel 2-Ton Long Reach product photo
Low cars

AV Steel 2-Ton Long Reach

2 ton · 3 to 24-3/8 in · 36 in reach

A long, low frame for lift points set deep under the body.

SuitsCamaro, Corvette, Malibu, Cruze
View on Amazon →

Sorting the Chevy Lineup by Lifting Needs

Chevy models fall into three rough groups when you go to lift them, and each group stresses a different part of the jack.

  • Pickups and full-size SUVs: the Silverado, Colorado, Tahoe and Suburban are heavy and tall. Capacity matters, but maximum lift height is usually the limit, especially on 4×4 trims with bigger tires.
  • Crossovers and sedans: the Equinox, Traverse, Trax, Blazer, Malibu and Cruze sit in the middle. Most 3-ton jacks with a lift range near 18 to 20 inches handle them.
  • Low cars: the Camaro and Corvette have low noses and lift points set well under the body. They need a jack that starts very low and reaches far under the car.

Reading the Specs: Capacity, Range and Reach

Capacity and lift range do most of the sorting. A floor jack lifts one end or one corner, not the whole vehicle, so a 3-ton rating already leaves margin on most half-ton trucks.

  • Minimum height: the saddle height with the arm fully down. Under about 4 inches suits lowered and sporty cars.
  • Maximum height: measure from the floor to your lift point, then add the few inches it takes for the tire to clear the ground. Trucks often need 20 inches or more.
  • Frame length: a long frame reaches lift points far under a car without the handle hitting the bumper.
  • Pump design: dual-piston or quick-lift pumps bring the saddle up to the vehicle in fewer strokes.

A jack is only one part of a home tool kit. Our list of car maintenance tools for beginners covers the stands, sockets and torque wrench that go with it.

Best Floor Jack for Chevy: Six Jacks Compared

These six cover heavy trucks, crossovers and low sports cars. Match the lift range on each listing to the height of your own lift points before ordering.

1. OEMTOOLS 24837: 3.5-Ton Low Profile Jack with Dual Pump and 20-1/2 Inch Lift

OEMTOOLS 24837 product photo
Key features
  • 3.5-ton (7,000 lb) rated capacity
  • Lift range 3-3/4 to 20-1/2 inches
  • Dual pump for fewer handle strokes
  • Overload and bypass safety valves

The OEMTOOLS 24837 is a steel floor jack rated at 3.5 tons, or 7,000 pounds. Its lift range is the main reason it suits a mixed Chevy garage: the saddle sits 3-3/4 inches off the floor when lowered and climbs to 20-1/2 inches at full height. That spread covers a lowered sedan at one end and many stock pickups at the other.

A dual pump raises the saddle with fewer strokes, which helps when the arm has a long way to travel to reach a truck frame. The listing also describes an overload valve that stops lifting beyond the rated capacity and a bypass valve that prevents over-extension. A 4.3-inch saddle comes with a support pad, and the handle has foam covering so it is less likely to mark a bumper or rocker panel.

For an Equinox, Malibu, Traverse or Blazer, this jack has plenty of reach and capacity. On a Silverado 1500 or Tahoe, measure your lift points first, because a 4×4 trim on tall tires can need more than 20-1/2 inches to clear the ground. It is a heavy steel jack, so it suits a garage floor more than a trunk, and the vehicle still goes onto jack stands before any work underneath.

View OEMTOOLS 24837 on Amazon

2. Auto Dynasty 4-Ton Floor Jack: 8,000 lb Steel Jack with Dual Pistons and 20 Inch Lift

Auto Dynasty 4-Ton product photo
Key features
  • 4-ton (8,000 lb) capacity
  • Lift range 4.5 to 20 inches
  • Dual piston quick lift pump
  • Heavy-duty steel, 26 x 12 inch frame

Auto Dynasty’s 4-ton jack is a steel low profile design rated for 8,000 pounds. The listing gives a lift range of 4.5 inches at the bottom and 20 inches at the top, with an overall footprint of about 26 by 12 inches. A dual piston hydraulic pump brings the saddle up quickly before the load comes on.

The higher rating does not mean you can lift the whole truck. A floor jack raises one end or one corner, and a 4-ton unit simply leaves more margin when that corner belongs to a Tahoe, Suburban or crew cab Silverado. The heavier steel frame also tends to feel steadier at full height than a lighter jack. A large saddle, casters and a built-in safety release valve round out the features in the listing.

This is a good match for a driveway or garage that sees mostly trucks and full-size SUVs. The 4.5-inch minimum height is too tall for a Camaro or Corvette without ramps, so owners of low cars should look elsewhere. As with any steel 4-ton jack, it is heavy to move around and store, so plan a spot on the garage floor for it. Pair it with stands rated for the truck’s weight.

View Auto Dynasty 4-Ton on Amazon

serene snow-covered road winding through a dense evergreen forest under a bright winter sky

3. Maxority 3-Ton Off Road Floor Jack: Dual Pistons with Foot Pedal and Extension Adapter

Maxority 3-Ton Off Road Jack product photo
Key features
  • 3-ton (6,600 lb) capacity
  • Dual piston quick lift pump
  • Spring-loaded foot pedal for lowering
  • Extension adapter for taller vehicles

Maxority sells this 3-ton jack as an off-road version of its low profile steel floor jack. It is rated for 6,600 pounds and uses a dual piston quick lift pump to take up the slack before the saddle meets the frame. The listing describes a slim profile for low vehicles and an included extension adapter that raises the saddle for taller ones.

That adapter is the reason it appears here. A lifted Silverado or a Colorado on larger tires can leave a standard jack short of the frame, and an extension that sits in the saddle adds the height back without buying a second jack. A spring-loaded foot pedal allows controlled lowering with your hands free to guide the vehicle down, which is useful when a heavy truck settles onto stands.

The listing does not state an exact lift range, so measure your truck and confirm the minimum and maximum heights on the Amazon page before ordering. Use the adapter only as the maker intends, seated fully in the saddle and centered under a solid lift point. For a stock truck this jack is more than you need, and for very low cars a long-frame jack is a better choice.

View Maxority 3-Ton Off Road Jack on Amazon

4. AV Steel 2-Ton Extra Long Reach Floor Jack: 3 to 24-3/8 Inch Lift with Dual Piston Pump

AV Steel 2-Ton Long Reach product photo
Key features
  • 2-ton (4,000 lb) capacity
  • Lift range 3 to 24-3/8 inches
  • 36-inch extra long reach frame
  • Overload valve and 360-degree saddle

This AV Steel jack is built for low cars rather than trucks. It is rated at 2 tons, or 4,000 pounds, and the listing gives a lift range from 3 inches up to 24-3/8 inches. The frame is long, with a 36-inch reach, so the saddle can get to lift points well under the body while the handle stays clear of the bumper.

That combination suits a Camaro or Corvette, where the front lip sits low and the lift points are set back. It also works on a Malibu or Cruze for brake and tire jobs. A dual piston pump speeds up the early strokes, an overload protection valve stops lifting past the rating, and a large saddle rotates 360 degrees to line up with a lift pad. Two rear wheels rotate for repositioning.

AV Steel states plainly that this jack is not recommended for trucks, heavy SUVs, minivans or lifted vehicles, so keep it away from a Silverado or Tahoe. The long frame also takes more floor space in a small garage. If you work on a Corvette often, check whether your car needs specific jacking pads before lifting, and put it on stands before you slide underneath.

View AV Steel 2-Ton Long Reach on Amazon

aerial view of a winding mountain road surrounded by autumn trees and vibrant foliage

5. Henf 3-Ton Low Profile Floor Jack: 6,600 lb Steel Jack with 3.3 to 18.5 Inch Lift

Henf 3-Ton Low Profile product photo
Key features
  • 3-ton (6,600 lb) capacity
  • Lift range 3.3 to 18.5 inches
  • Dual piston quick lift pump
  • Rubber saddle and foam handle bumper

Henf’s 3-ton jack is a heavy-duty steel low profile design rated for 6,600 pounds. The listing gives a lift range from 3.3 inches to 18.5 inches, so the saddle slides under a sedan with a flat tire and still lifts a crossover high enough for wheel and brake work. A dual piston pump raises the saddle quickly before the load comes on.

Several small details protect the vehicle. The saddle has a rubber pad, the handle carries a foam bumper so it is less likely to scuff a fascia, and the 360-degree saddle can be removed and replaced if it wears. Steel rear casters and swivel front casters help you roll it into position. The listing also states that the jack meets the ANSI/ASME PASE safety standard.

For a Malibu, Cruze, Trax or Equinox, this jack covers the usual jobs, including the twice-a-year wheel swap many West Michigan drivers make before and after winter. The 18.5-inch maximum is the limit to watch: a Silverado 1500 or Tahoe, especially a 4×4, may need more height to get a tire off the floor. It is all steel, so it is heavier to carry than a hybrid aluminum jack. Set the vehicle on stands before working beneath it.

View Henf 3-Ton Low Profile on Amazon

6. winturbor 3-Ton Floor Jack: 7.6 to 21.3 Inch Lift with Rubber Pads and Carry Bag

winturbor 3-Ton product photo
Key features
  • 3-ton (6,000 lb) capacity
  • Lift range 7.6 to 21.3 inches with pad
  • Two rubber pads included
  • Carry bag and tire repair kit

The winturbor 3-ton jack is a steel unit rated for 6,000 pounds with a lift range of 7.6 to 21.3 inches when the rubber pad is fitted, or 20.9 inches without it. The higher starting point means it is aimed at vehicles with more ground clearance rather than low cars. The listing names sedans, SUVs, light pickups and minivans as the intended range.

Two rubber pads come in the box to protect lift points and underbody paint, and they also add grip on the saddle. Rear swivel casters and a top carry handle help position it, and the handle detaches for storage. A carry bag and a tire repair kit are included, so the jack can ride in the cargo area of a Traverse or the bed of a Colorado for a roadside flat.

The 7.6-inch minimum rules out a Camaro, Corvette or a Malibu with a flat tire, because the saddle will not fit under the lift point. On an Equinox, Traverse, Blazer or Colorado the reach is a good fit. An overload valve limits lifting to the rated capacity. Use it on firm ground, and set stands under the vehicle before any work beneath it.

View winturbor 3-Ton on Amazon

Matching a Jack to Your Chevy Model

The best floor jack for Chevy drivers depends on the model group. Trims, tire sizes and lift kits change the numbers, so measure your own vehicle first.

Chevy model groupWhat to look forJacks from this list
Silverado 1500, Tahoe, Suburban3 tons or more, about 20 inches of liftAuto Dynasty 4-ton, OEMTOOLS 24837
Lifted Silverado or ColoradoExtra height or an extension adapterMaxority 3-ton with adapter
Equinox, Traverse, Blazer, Trax3 tons, 18 to 21 inches of liftwinturbor 3-ton, Henf 3-ton
Malibu, Cruze, Camaro, CorvetteLow entry and a long frameAV Steel 2-ton, OEMTOOLS 24837
Floor jack features matched to common Chevrolet model groups

Corvette owners have a few extra concerns, such as splitters and specific lift pads, which our Corvette floor jack guide covers in detail. For a lifted pickup, the floor jack for trucks guide goes further into tall jacks.

blurred view of a coastal road and ocean

Lift Points, Stands and Garage Habits

The right lift point changes from model to model and year to year. Chevrolet’s manuals and guides page lets you pull up the owner’s manual for your year and model, and the vehicle care section shows where the body or frame can take a jack.

  1. Start on concrete: asphalt driveways soften in summer, and the small wheels of a floor jack can dig in.
  2. Chock the opposite end: set the parking brake and block the wheels that stay on the ground.
  3. Lift at the marked point: a pinch weld, frame rail or axle as the manual shows, never the oil pan or a plastic panel.
  4. Move the weight to stands: set jack stands under a solid point and lower the vehicle onto them before you reach underneath.

For a heavy pickup, our guide to jack stands for trucks covers taller and higher-rated stands.

scenic view of a dirt road stretching through a vast countryside field at dusk

West Michigan winters are hard on hydraulic tools. Salt dripping off a Silverado lands on the jack, so wipe it down and store it with the ram lowered. A jack that creeps down under load needs service or replacement.

Jobs Better Done on Our Lift

A floor jack handles tire rotations, brake pad swaps and oil changes. Once a job means compressing springs, pressing in ball joints or finding a clunk under load, a two-post lift and the right tools make it safer. Our suspension repair team in Grand Rapids handles shocks, control arms and steering parts on Chevy trucks and cars.

lush green landscapes and winding roads in a serene tea plantation setting

A Silverado that tows, plows or idles through winter often falls under the severe-service schedule in its manual. Our factory scheduled maintenance service keeps it on the intervals Chevrolet lists, so the jack at home can stay for the quick jobs.

Frequently Asked Questions

Will a 3-ton floor jack lift a Silverado 1500?

In most cases, yes. A floor jack only lifts one end or corner, so a 3-ton rating leaves margin on a half-ton truck. Lift height is the usual problem, so check that the jack reaches high enough to raise the tire off the floor.

Where do I put a floor jack on a Chevy?

Use the lift points your owner’s manual shows for your year and model. On cars and crossovers that is usually a reinforced pinch weld area, and on trucks a frame rail or axle. Never lift on the oil pan, a plastic panel or a suspension arm the manual doesn’t mark.

Can one jack handle both a Camaro and a Silverado?

A low-entry jack with about 20 inches of lift, like the OEMTOOLS 24837, comes close. A stock 4×4 or lifted Silverado may still need more height, so some owners keep a second taller jack or use ramps for the car.

What is the best floor jack for Chevy SUVs like the Tahoe?

A 3-ton or 4-ton steel jack with roughly 20 inches of lift suits a Tahoe or Suburban. The Auto Dynasty 4-ton gives extra capacity margin, and either way the SUV goes onto jack stands before any work underneath.

Lifted your Chevy and found a torn boot, a leaking shock or worn pads? Give 456 AutoFix a call at 616-279-3832 on weekdays between 8am and 5pm, or request a time through our contact page.

If your workday overlaps our hours, the after-hours drop-off at 456 Carrier St NE in Creston lets you leave the keys with us.