As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
Subaru builds cars at both ends of the height scale. An Outback, Forester or Ascent rides high on its all-wheel-drive platform, while an Impreza, WRX or BRZ sits much closer to the pavement. The best floor jack for Subaru owners is the one that slides under your particular model, reaches its lift point and still raises the tire clear of the floor.
Below, we explain how to size a jack to your car, then look at six floor jacks listed on Amazon, from light aluminum models that cover low and tall cars alike to a 3.5 ton steel unit for the largest crossovers. If you are still putting together a home kit, our guide to car maintenance tools for beginners shows where a jack sits among the other basics.
Quick answer
What floor jack suits a Subaru?
For an Outback, Forester or Ascent, pick a jack that lifts to about 19 inches or more, such as the Performance Tool W1645. If you own both low and tall Subarus, the light OTC LDJA2 aluminum jack covers both. For an Impreza or WRX alone, the Torin 2.5 Ton works well. Always finish on jack stands.
Our Quick Picks
Three quick picks: a light jack for mixed Subaru garages, a high-capacity jack for the big crossovers and a plain car jack for sedans. All six are reviewed below.

OTC LDJA2 2-Ton Aluminum Jack
One light jack that reaches under a WRX and up to an Outback.

Performance Tool W1645 3.5 Ton Jack
The most capacity and the tallest reach of the six jacks.

Torin 2.5 Ton Trolley Jack
A conventional steel trolley jack sized for cars rather than crossovers.
Height, Reach and Lift Points on a Subaru
Three measurements decide whether a jack works on your car, and capacity is rarely the one that causes trouble.
- Starting height: the saddle has to slide under the car before it can lift. Low cars like the BRZ and WRX need a jack that starts around 3.5 inches or lower, especially with a front lip.
- Top height: crossovers sit high, so the jack must travel far enough to lift the tire off the floor once the suspension has fully extended. Look for a maximum near 19 inches for the tall models.
- Reach: a long chassis lets the saddle get to a center lift point without the jack body hitting the bumper cover.
Your owner’s manual is the authority on where the jack goes. Many Subarus show center garage-jack points under the front and rear of the car, separate from the side pinch-weld points meant for the spare-tire jack. Center the saddle on the marked point, and use a rubber pad if the surface is narrow or painted.
Matching Capacity to the Model You Drive
A floor jack lifts one end or one corner, not the whole car, so a 2 ton jack covers a compact sedan with room to spare. The heavier crossovers, especially a loaded three-row Ascent, are better matched with 2.5 tons or more, which keeps the jack working well below its limit.
Steel jacks are sturdy but heavy, while aluminum designs are easier to carry. For low cars, our guide to the best low profile floor jack for cars covers more slim designs worth a look.
Best Floor Jack for Subaru Models: Six Jacks Compared
Capacities and lift ranges below come from each Amazon listing. Choosing the best floor jack for Subaru work means comparing them with your own car’s lift points and clearance.
1. OTC LDJA2 2 Ton Aluminum Racing Jack: 3-1/4 to 18-1/2 Inch Lift at 41 Pounds

- 2 ton lifting capacity
- 3-1/4 to 18-1/2 inch lift range
- 41 lb aluminum build with side handles
- Meets ASME PASE-2019 for service jacks
OTC’s LDJA2 is a 2 ton aluminum racing jack with an unusually wide lift range for its size. The listing gives a range of 3-1/4 to 18-1/2 inches and a weight of 41 pounds. That combination lets one jack slide under a BRZ or WRX and still raise an Outback or Forester wheel clear of the floor, which suits a household with more than one Subaru.
Side handles make it easy to carry from the garage to the driveway, and a padded lower handle helps protect bumper covers while you pump. A rubber saddle grips the lift point and guards painted or coated surfaces. The listing states that the jack meets the ASME PASE-2019 safety standard for service jacks, and it comes with an owner’s manual that includes operating instructions, plus multilingual safety and capacity markings.
The main limit is capacity. Two tons is plenty for lifting one end of a Crosstrek, Impreza or Outback, but a loaded three-row Ascent leaves less margin, and a higher-rated jack is the more comfortable match there. Aluminum also needs a little care: keep it out of salty slush and wipe it down after winter use so the finish and the moving parts stay in good shape.
View OTC LDJA2 2-Ton Aluminum Jack on Amazon
2. Performance Tool W1645 3.5 Ton Floor Jack: 3-5/8 to 20-1/2 Inch Lift with Double Pump

- 3.5 ton (7,000 lb) capacity
- 3-5/8 to 20-1/2 inch lift range
- Double-pump mechanism for quick lifting
- Bypass valve overload protection
Performance Tool’s W1645 is the highest-rated jack in this guide, at 3.5 tons or 7,000 lb. Its listed lift range runs from 3-5/8 to 20-1/2 inches, the tallest top height here. That extra travel is useful on an Ascent, an Outback or a Forester on larger tires, where a shorter jack can run out of stroke before the tire leaves the ground.
A double-pump mechanism is listed for quick lifting, so the saddle reaches the lift point in fewer strokes. A rubber saddle pad helps protect the underside of the car, and a bypass valve provides overload protection if the load goes past the rating. The listing calls it a low profile swiveling floor jack, a layout meant to make it easier to steer the saddle toward a center lift point under the front of the car.
With that much capacity, expect a bigger tool than the aluminum jacks here, one that is better kept on the garage floor than in the cargo area. The 3-5/8 inch starting height still clears most Subaru sedans, but a BRZ with a front lip may leave too little room. It suits owners who mostly work on the tall models and want generous reserve capacity.
View Performance Tool W1645 3.5 Ton Jack on Amazon

3. Torin 2.5 Ton Low Profile Trolley Jack: 3-3/8 to 14-15/16 Inch Lift for Cars

- 2.5 ton (5,000 lb) capacity
- 3-3/8 to 14-15/16 inch lift range
- Single piston quick lift pump
- Safety bypass prevents overloading
Torin’s 2.5 ton trolley jack is a plain steel design aimed at cars. The listing gives a 5,000 lb rating and a range of 3-3/8 to 14-15/16 inches, and its own description says it is not recommended for SUVs and trucks. For Subaru owners, that points it at the Impreza, Legacy, WRX and BRZ rather than the taller wagons and crossovers.
A single piston quick lift pump brings the saddle up to the lift point before the load takes over, so less of your pumping is spent on empty travel. A safety bypass system is listed to prevent overloading. Two large steel front wheels and two 360-degree swivel casters handle steering on concrete, and a built-in carry handle helps when you move it out to the driveway.
The heavy steel frame gives it a solid feel on a flat floor, at the cost of extra weight. Torin lists a limited one-year manufacturer warranty. It suits a sedan owner who wants a basic, conventional jack for tire swaps, brake pad changes and oil changes on stands, and who does not need the extra reach that a crossover asks for.
View Torin 2.5 Ton Trolley Jack on Amazon
4. ANTPOWER 2 Ton Aluminum Floor Jack: 3.36 to 17.2 Inch Lift with Dual Piston Pump

- 2 ton (4,409 lb) capacity
- 3.36 to 17.2 inch lift range
- Aluminum and steel build
- Dual piston pump, rubber saddle
ANTPOWER’s 2 ton jack combines an aluminum body with steel parts and lists a capacity of 4,409 lb. Its lift range runs from 3.36 to 17.2 inches, which covers the low Subaru sedans and gives reasonable height for a Crosstrek or Legacy. Aluminum construction makes it easier to move than an all-steel jack of similar size.
A dual piston pump raises the saddle faster than a single pump design, according to the listing. The large non-slip rubber saddle grips the chassis and helps prevent scratches on painted surfaces. Two universal casters at the rear and two front rollers handle positioning, and the maker states the jack is tested to ASME and GS safety standards, with a limited one-year manufacturer warranty.
The 17.2-inch maximum is the figure to check against a taller Subaru. On an Outback or Forester it may be enough at some lift points and short at others, depending on tire size and how far the suspension droops as the car rises. Measure before you order if a crossover is in the picture. If you mainly drive an Impreza, WRX or Crosstrek and want something easy to carry, it fits that role well.
View ANTPOWER 2 Ton Aluminum Jack on Amazon

5. YELLOW JACKET 2.5 Ton Racing Jack: 3-15/16 to 18-5/16 Inch Lift with Dual Pump

- 2.5 ton (5,500 lb) capacity
- 3-15/16 to 18-5/16 inch lift range
- Aluminum and steel construction
- Overload protection, foam handle bumper
The YELLOW JACKET 2.5 ton jack mixes aluminum and steel and lists a 5,500 lb capacity. Its range runs from 3-15/16 to 18-5/16 inches, so it leans toward the taller side of the Subaru lineup. For an Outback, Forester or Crosstrek, that top height gives room to lift a wheel clear of the floor for a brake job or a seasonal swap.
A dual pump system lifts faster than a single pump, according to the listing, and an overload protection system guards against lifting past the rating. A large rubber saddle and a foam bumper on the handle help protect the car. Two 360-degree swivel casters and two front rollers make it easy to move, and a side handle helps you place it. The maker states it meets ANSI/ASME safety standards and backs it with a one-year warranty.
The starting height of nearly 4 inches is the catch for the lowest cars. A stock Impreza usually leaves enough room, but a BRZ or WRX with a front lip may not. If your garage holds only crossovers and wagons, that matters little, and the mixed frame is easier to move than a full steel jack.
View YELLOW JACKET 2.5 Ton Jack on Amazon
6. DRIVEUPTOOLS 2.5 Ton Low Profile Jack: 3.3 to 15 Inch Lift with Steel Frame

- 2.5 ton (5,500 lb) capacity
- 3.3 to 15 inch lift range
- Reinforced steel frame, rubber saddle pad
- 2-year DriveUpTools warranty
The DriveUpTools jack sits between the compact car jacks and the tall models in this list. Its listing gives a 2.5 ton (5,500 lb) rating, a 3.3-inch starting height and a 15-inch top height, and describes it as built for cars, sedans, crossovers and most SUVs. For a Crosstrek or Impreza, that range covers the usual tire, brake and suspension jobs.
The frame is reinforced steel, and a rubber saddle pad helps protect lift points through repeated use. The hydraulic unit is listed as raising the vehicle in fewer pumps, and the compact body is meant to store easily in a trunk or a garage corner. DriveUpTools backs it with a two-year warranty, longer than the one-year terms listed for the Torin, ANTPOWER and YELLOW JACKET jacks here.
Check the top height against your own car before buying it for an Outback or Forester. Measure from the floor to your lift point, add the few inches it takes for the tire to clear the ground, and compare the total with the listed 15 inches. Taller winter tires or a lifted suspension both eat into that margin. For a Crosstrek, Impreza or Legacy owner who wants a simple steel jack, it is a sensible middle choice.
View DRIVEUPTOOLS 2.5 Ton Jack on Amazon
Which Jack Fits Which Subaru
Ground clearance varies by trim and tire size, so treat this as a starting point and measure your own car.
| Subaru type | What it needs | Jacks that fit |
|---|---|---|
| BRZ, WRX and Impreza | Low start, light weight | OTC LDJA2, Torin 2.5 Ton, ANTPOWER 2 Ton |
| Legacy and Crosstrek | Low start with a medium top height | DRIVEUPTOOLS 2.5 Ton, ANTPOWER 2 Ton |
| Outback and Forester | Tall top height, steady base | OTC LDJA2, YELLOW JACKET 2.5 Ton, Performance Tool W1645 |
| Ascent | Extra capacity and tall reach | Performance Tool W1645 |

If two Subarus share your driveway, a jack with a wide range covers both. The best floor jack for Subaru households with a sedan and a wagon is usually one that starts under 3.7 inches and tops out above 18, like the OTC LDJA2 or the Performance Tool W1645.
Seasonal Swaps in a West Michigan Garage
Many Grand Rapids drivers swap to winter wheels in the fall and back in spring, and the best floor jack for Subaru owners makes that job far quicker than the spare-tire jack. Loosen the lug nuts while the tire is still on the ground, lift one corner, then set a stand before you pull the wheel.
Cold matters in an unheated garage. Hydraulic oil thickens as the temperature drops, so a jack can pump more slowly on a January morning. Road salt also settles on crossmembers and differential housings, so wipe the lift point before you set the saddle on it.

A jack is a lifting tool, not a support. The ASME PASE safety standard covers both mobile jacks and automotive stands as separate equipment, each with its own rules for operation and inspection. Once the car is up, lower it onto rated stands placed at the points your manual shows, as covered in our guide to jack stands for home garage use.
When the Job Belongs at a Shop
With a wheel off, you get a clear view of the brakes, suspension and hub. Thin pads, a grooved rotor, a leaking strut or a rumbling hub are worth checking soon. Our guides to brake pads for Subaru and Subaru wheel bearings explain the parts involved.

Our shop handles brakes, suspension, steering, wheel bearings and timing belts on foreign and domestic vehicles. If you would rather keep the car on its maker’s plan without crawling underneath, book factory scheduled maintenance in Grand Rapids and mention anything you noticed during your last tire swap.
More Buying Guides
Frequently Asked Questions
Where do you put a floor jack on a Subaru?
Use the garage-jack points shown in your owner’s manual. On many Subarus these are center points under the front and rear, separate from the side pinch welds meant for the spare-tire jack. Center the saddle on the point and use a rubber pad if it is narrow.
What size floor jack do I need for a Subaru Outback?
Look for a top height near 19 inches and at least 2 tons of capacity, with 2.5 tons or more adding margin. The extra height lets the tire clear the floor once the suspension extends. Check your own car’s clearance and weight before you order.
Do I need a low profile jack for a WRX or BRZ?
Usually, yes. These cars sit low, and a front lip or aero trim leaves little room for a standard jack. A jack that starts near 3.5 inches or lower, with a long reach, slides under without scraping.
Can I work under my Subaru with only a floor jack?
No. A floor jack is made for lifting, and its hydraulics can bleed down or the car can shift. Lower the car onto rated jack stands at the points your manual shows before any part of you goes underneath.
Found worn brakes or a noisy bearing while your Subaru was up on stands? Give 456 AutoFix a call at 616-279-3832 between 8am and 5pm on weekdays, or set up an appointment on our contact page.
Working hours tight? Bring the car to 456 Carrier St NE in Creston after we close and leave it with our after-hours drop-off.
