456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Stock, Heavy or Lifted: Picking the Best Floor Jack for Trucks

best floor jack for trucks: skilled carpenter working in a workshop

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A pickup asks more of a jack than a sedan does. The front end is heavy, the frame sits high, and a lot of trucks around Grand Rapids live on gravel driveways or in garages that drop well below freezing in January. The best floor jack for trucks is the one that reaches your lifting point, raises it high enough for a stand, and does it with capacity to spare.

Below you will find how to size a jack for your truck, five jacks that suit pickups from stock half-tons to lifted rigs, and the safety steps that matter most. If you also own a low car, our guide to low profile floor jacks for cars covers the other end of the height problem.

Quick answer

What kind of floor jack does a pickup truck need?

Look for a 3 to 4 ton jack whose maximum height clears your frame or axle with room for a stand. The AFF 3.5 Ton spans 3.35 to 24.2 inches for stock and leveled trucks, the Big RED 4 Ton adds capacity for heavy pickups, and the JEGS off-road jack reaches 28 inches for lifted trucks.

Our Quick Picks

Three jacks for the usual pickup situations: a mixed garage with a truck and a car, a heavy full-size truck and a lifted rig.

AFF 3.5 Ton High Lift product photo
Widest range

AFF 3.5 Ton High Lift

3.5 ton, 3.35 to 24.2 in.

One jack that starts low and still reaches a leveled pickup.

SuitsGarages with a truck and a car
View on Amazon →
Big RED 4 Ton product photo
Heavy pickups

Big RED 4 Ton

4 ton, 3-7/8 to 20 in.

Extra capacity margin for full-size and three-quarter-ton trucks.

SuitsOwners of crew cabs and diesel pickups
View on Amazon →
JEGS 3-Ton Off-Road Jack product photo
Lifted trucks

JEGS 3-Ton Off-Road Jack

3 ton, 6 to 28 in.

A tall reach and big wheels for raised trucks and rough ground.

SuitsLifted pickups and gravel driveways
View on Amazon →

Why Lift Height Matters More Than Tonnage

Most shoppers start with the ton rating, but on a pickup the number that usually decides the job is maximum height. A jack only raises one end or one corner of the truck, so a 3 ton jack already covers a large share of light-duty pickups. What catches people out is a saddle that tops out before the tire leaves the ground, or before there is space to slide a stand underneath.

Measure before you buy. With the truck parked on level ground, take three numbers:

  1. Lift point height: floor to the frame rail, axle tube or jacking point your owner’s manual shows.
  2. Travel needed: how far that point must rise for the tire to clear the ground, plus a couple of inches of working room.
  3. Stand height: the setting your jack stands will sit at under that point.

Add the first two numbers and compare the total with the jack’s listed maximum. If the jack only just makes it, pick a taller one. Also check the minimum height against anything low in the path, such as a front air dam or a hitch receiver.

Matching a Jack to the Way You Use Your Truck

Capacity still matters for heavier trucks. A crew cab with a diesel engine puts a lot of weight over the front axle, and a jack that works well within its rating feels steadier than one running near its limit. For three-quarter-ton and heavier pickups, a 4 ton jack is a sensible floor. Your door jamb sticker lists the axle ratings if you want a rough idea of how much each end carries.

Lifted and leveled trucks change the picture again. A typical service jack tops out around 20 inches, which can leave a raised truck barely off the ground. That is why off-road jacks with 23 to 28 inches of reach exist, and why they usually start higher off the floor too. Pick the range that brackets your own measurements, not the biggest number on the shelf.

Then think about where you work. Small steel casters roll well on concrete but dig into gravel and soft dirt, while big wheel jacks are built for rougher ground. If you are still putting together a home garage, our list of car maintenance tools for beginners shows where a jack and stands fit among the basics.

Best Floor Jack for Trucks: Five Jacks Compared

Each listing below gives capacity and lift range from the maker or the Amazon listing. Compare those figures with the measurements you took from your own truck.

1. AFF 3.5 Ton: Low Profile High Lift Floor Jack, 3.35 to 24.2 in.

AFF 3.5 Ton High Lift product photo
Key features
  • 3.5 ton rated capacity
  • Lift range of 3.35 to 24.2 in.
  • Heavy-gauge steel frame with chassis flanges
  • Two-piece 50 in. handle, rubber saddle pad

The AFF 3.5 ton floor jack covers an unusually wide span: its listing gives a low height of 3.35 inches and a high height of 24.2 inches. That combination is rare. Most jacks that start low enough for a sedan top out near 20 inches, while most tall jacks start too high to fit under a car, so this one can serve a stock or leveled pickup and the household car from the same spot on the floor.

AFF calls its hydraulic system Lightning Lift, aimed at an easy stroke and a quick rise to the load. The frame is heavy-gauge steel with upper and lower flanges on the chassis to resist twisting under load, and the finish is a UV powder coat. A foam bumper on the handle and a rubber saddle pad help protect paint and lift points, and the two-piece handle comes apart for storage.

The listed specs describe a big jack: a 50 inch handle, a chassis about 31.3 inches long and a shipping weight near 107 lbs. Plan on it living in the garage. If your truck carries a tall lift, the 24.2 inch top may still fall short, so compare it with your measurements before ordering.

View AFF 3.5 Ton High Lift on Amazon

2. Big RED 4 Ton: 8,000 lb Steel Service Jack with Dual-Piston Pump

Big RED 4 Ton product photo
Key features
  • 4 ton (8,000 lb) capacity
  • Lift range of 3-7/8 to 20 in.
  • Dual piston quick-lift pump
  • Safety bypass, meets ASME standards

Big RED, a Torin brand, rates this steel service jack at 4 tons (8,000 lb), which gives a comfortable margin when you lift the heavy front end of a crew cab or a diesel pickup. You only ever raise one end or one corner at a time, but a jack that works well below its limit tends to feel steadier and keeps its seals under less strain. The listing gives a lift range of 3-7/8 to 20 inches.

A dual piston pump moves the saddle faster than a single pump, and Big RED describes it as suited to most cars, trucks and SUVs. The frame rolls on two large steel casters at the back and two 360-degree swivel casters at the front, with a wide stance for stability once the load is up. A safety bypass prevents overloading, and the jack meets ASME safety standards with a one year limited warranty.

The 20 inch top height is the figure to check. On a stock pickup that is usually enough to set a stand under the frame or axle, but a leveled or lifted truck may need a taller jack. It is a heavy shop-style tool, so plan for a permanent spot on the garage floor.

View Big RED 4 Ton on Amazon

aerial view of a winding road surrounded by greenery and lakes

3. JEGS Off-Road Floor Jack: 3 Ton, 28 in. Lift and Large Wheels

JEGS 3-Ton Off-Road Jack product photo
Key features
  • 3 ton rated capacity
  • Minimum height 6 in. (155 mm)
  • Maximum height 28 in. (710 mm)
  • Large 6 in. and 8 in. wheels

This heavy-duty off-road floor jack, sold through JEGS, solves the problem most garage jacks have with lifted trucks: running out of height. Its listing gives a 3 ton rating with a maximum height of 28 inches (710 mm), several inches above a typical service jack. That extra reach lets the saddle meet the axle or frame of a raised pickup without stacking wood blocks under it.

The other standout is the wheel set. Large 6 inch and 8 inch wheels roll more easily over gravel, packed dirt and cracked concrete than the small casters on a standard trolley jack, which helps if you work on a driveway or at a hunting camp rather than on a smooth floor. The frame combines aluminum and steel, a common way to save weight on a jack of this size.

The trade-off sits at the bottom of the range. A 6 inch (155 mm) minimum height will not slide under a car or a stock truck with a low air dam, so this is a specialist jack for raised vehicles. Pair it with tall stands, because a stand that tops out low cannot use the height it gives you.

View JEGS 3-Ton Off-Road Jack on Amazon

4. DNA MOTORING 3 Ton: Steel Floor Jack, 7.7 to 21 in. Lift with Case

DNA MOTORING 3 Ton product photo
Key features
  • 3 ton (6,000 lbs) capacity
  • Lift range of 7.7 to 21 in.
  • Overload safety release valve
  • Rubber saddle pad and carrying storage case

The DNA MOTORING 3 ton jack is a steel trolley jack rated for 6,000 lbs, with a listed lift range of 7.7 to 21 inches. That 7.7 inch starting height tells you who it is for. It will not slide under a low car, but on a pickup or SUV the saddle begins closer to the frame or axle, so fewer pump strokes go into empty travel before it takes the load.

A built-in safety release valve opens if the jack is overloaded, which helps prevent damage or injury. The large saddle carries a rubber pad for extra grip and some protection for the lift point, and the chassis rolls on large steel casters plus 360-degree swivel casters. The listing also includes a carrying storage case, a useful touch if the jack has to share a crowded garage shelf or travel to a camp.

DNA MOTORING is clear that the jack is for lifting only. It must not hold a load for long periods the way a stand does, and it is meant for straight vertical lifts, not jobs that push sideways or down. Treat the 21 inch top as the limit for a stock truck rather than a lifted one.

View DNA MOTORING 3 Ton on Amazon

neatly organized workshop with tools

5. AV Steel 4 Ton: 8,000 lb Floor Jack for Pickups and Vans

AV Steel 4 Ton product photo
Key features
  • 4 ton (8,000 lbs) capacity
  • Lift range of 4-1/4 to 19-3/4 in.
  • Dual piston hydraulic pump
  • 360-degree rotating saddle, overload valve

The AV Steel 4 ton floor jack is a full-size steel unit rated for 8,000 lbs, with a lift range of 4-1/4 to 19-3/4 inches. The maker is unusually direct about fit: its listing says it suits most standard cars, SUVs, vans and pickup trucks, and is not recommended for sports cars, RVs, heavy commercial trucks or lifted vehicles. That honesty makes it easy to judge whether it belongs in your garage.

A dual piston pump raises the saddle with fewer handle strokes than a single piston design. A built-in safety valve prevents overloading, and the large saddle rotates 360 degrees so you can line it up with a frame rail or axle pad without moving the whole jack. Two rear rotating wheels handle repositioning, and the maker reminds owners to close the release valve fully before lifting.

The listing gives a weight of 87.3 lbs, so this is a jack that stays in one place. It fits the owner of a stock pickup or a work van who wants generous capacity and a simple steel design. Anyone running a leveling kit or bigger tires should look at the taller AFF or JEGS jacks, since 19-3/4 inches can come up short.

View AV Steel 4 Ton on Amazon

Which Jack Fits Which Truck?

Use this table as a starting point, then confirm the numbers against your own measurements. Trucks with aftermarket suspension or tires vary too much for any chart to settle the question.

Truck setupWhat to look forJacks from this list
Stock half-ton pickup3 ton or more, about 20 in. or higher at the topDNA MOTORING 3 Ton, Big RED 4 Ton
Heavy crew cab or three-quarter-ton4 ton rating for a wider safety marginBig RED 4 Ton, AV Steel 4 Ton
Leveled truck or larger tires23 in. or more of reachAFF 3.5 Ton, JEGS off-road
Lifted truckUp to 28 in. of reach and a higher starting heightJEGS off-road
Gravel or dirt drivewayLarge wheels and a wide baseJEGS off-road
Choosing the best floor jack for trucks by truck setup and work surface

One jack rarely covers every vehicle in a driveway. A household with a lifted pickup and a low sedan may end up with two, because a jack that reaches 28 inches cannot also slide under a car with a low front lip.

aerial photograph in a garage

Lifting a Pickup Safely in a West Michigan Garage

A floor jack is a lifting tool, not a support. The moment the wheel is off the ground, set a pair of stands rated for the truck and lower the load onto them before any part of your body goes underneath. The OSHA rules for jacks make the same point for workplaces: use a jack rated for the load, block the base when the footing is not firm, and secure the load as soon as it is raised.

  • Chock the wheels: block the tires that stay on the ground, and set the parking brake with the transmission in park.
  • Check the lift point: years of road salt can leave frame rails and pinch welds scaly, so inspect the spot before the saddle touches it.
  • Firm ground only: on gravel or asphalt on a hot day, put a wide plank under the stands so they cannot sink.
  • Expect slow pumping in the cold: hydraulic fluid thickens in an unheated garage, so give the jack a few slow strokes before it takes weight.
blue garage doors with a no parking sign painted outdoors

Look for jacks that state compliance with the ASME PASE safety standard for portable automotive service equipment, as the Big RED 4 Ton does. Inspect yours for leaks or a sinking saddle every season, and retire it if it will not hold a load. Our article on the car jack choices for BMW owners also shows how jack pads protect a finished lift point.

When the Job Belongs in a Shop

A good jack makes tire swaps, brake inspections and oil changes easier at home, but some truck work needs more than a jack and stands. Coil springs, ball joints and steering parts on a heavy pickup carry real stored force, and pressed-in wheel bearings need a press and the right adapters. Our suspension and steering repair in Grand Rapids handles that side of things.

curved road with snow banks and signs by a frozen lake under a cloudy winter sky

Some owners would also rather leave the full service schedule to someone with a lift. Our factory scheduled maintenance service in Grand Rapids follows your truck’s maker schedule, and if you plan to do the pads yourself, read our guide to choosing brake pads for trucks that tow and haul first.

Frequently Asked Questions

Is a 3 ton floor jack enough for a pickup?

For many light-duty pickups, yes, because the jack lifts only one end or one corner at a time. Heavier crew cabs, diesels and three-quarter-ton trucks are better served by a 4 ton jack, which works further below its limit.

How high should a floor jack lift for a lifted truck?

Measure from the floor to your lift point, then add the travel needed to raise the tire plus a little working room. Many lifted trucks need 23 to 28 inches, which is why off-road jacks such as the JEGS 3-ton model exist.

What is the best floor jack for trucks parked on gravel?

A jack with large wheels, such as the JEGS off-road model with its 6 and 8 inch wheels, rolls and sits better on loose ground than one with small casters. Put a wide board under your jack stands so they cannot sink.

Should I keep a floor jack in my truck?

Full-size floor jacks are heavy, so most owners keep them in the garage. For the road, carry the jack and tools that came with the truck, and check that you know where they are stored before you need them.

Rather have your pickup up on a proper lift for suspension, brake or maintenance work? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or request a time through our contact page.

If your workday runs past closing, the after-hours drop-off has you covered. Bring the truck to 456 Carrier St NE, Grand Rapids, and we will pick up from there.