As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
Mazda’s lineup runs from a low two-seat roadster to a three-row crossover, and one jack rarely serves both ends. The best floor jack for Mazda owners is the one that slides under your particular model, reaches its lift points and raises it high enough to pull a wheel.
This guide sorts the range by clearance, capacity and lift height, then reviews six jacks that suit different Mazdas. If you mostly work on low cars of any brand, our guide to the low profile floor jack for cars covers that side of the market in more depth.
Quick answer
Which floor jack suits an MX-5, a Mazda3 or a CX-90?
An MX-5 needs a light, low jack such as the SATA 1.5-ton hybrid. A Mazda3 or Mazda6 suits a low 2 ton jack like the TONDA. The CX-5, CX-50 and CX-90 call for a 3 ton jack with a tall lift range, such as the Daytona long reach.
Our Quick Picks
Three jacks that cover most Mazda driveways: a light one for the MX-5, a low 2 ton jack for the Mazda3 and Mazda6, and a tall-reaching 3 ton jack for the larger crossovers.

SATA 1.5-Ton Hybrid Jack
A light hybrid jack that slides under a low roadster and carries easily.

TONDA 2 Ton Low Profile Jack
A low aluminum and steel jack with enough capacity for the mid-size cars.

Daytona 3 Ton Long Reach Jack
A heavy steel jack with enough reach and height for the larger crossovers.
What a Mazda Asks of a Floor Jack
Four listing numbers decide whether a jack will work on your car.
- Minimum height: the saddle must fit under the lift point with the car on its tires. A Miata or a car with a front lip needs one that starts around 3 to 3-1/2 inches.
- Reach: a long frame lets the saddle reach a central point without the handle touching the bumper.
- Maximum height: about 14 inches is enough for a small car, but a crossover needs closer to 18 inches or more to get a tire clear of the floor.
- Capacity: a jack lifts one corner or end, but a healthy margin is safer on the heavier three-row models.
People searching for the best floor jack for Miata use, especially the best floor jack for ND Miata garages, usually care most about the first two numbers. Owners of a CX-5 or CX-90 care more about the last two.
Finding the Lift Points on Your Mazda
Every Mazda owner’s manual shows where the car may be lifted, and that page should guide where the saddle goes. Most Mazdas are unibody cars with reinforced points near each wheel along the pinch weld, and a flat saddle can fold that seam if it lands in the wrong place.
Mazda’s own MX-5 owner’s manual section on changing a tire is a good reminder of the basics. It asks you to park on hard, level ground, block the wheel diagonally opposite and never put any part of your body under a car held only by a jack. Mazda also notes that an MX-5 may or may not come with a jack at all.
Best Floor Jack for Mazda: Six Jacks in Detail
These six models run from the lightest roadster jack to the tallest crossover jack, and choosing the best floor jack for Mazda use comes down to which end of that range you drive.
1. SATA 1.5-Ton Hybrid Jack: 3-1/2 in. to 14 in. Lift with Dual-Piston Pump

- 1.5 ton (3,300 lb) rated capacity
- 3-1/2 in. to 14 in. lift range
- Aluminum and steel hybrid frame
- Overload tested to 1.5x rating
SATA built this compact jack around a mixed frame, with aluminum where weight can be saved and steel where the load is carried. The result is a jack that one person can lift into a trunk or carry across the garage by its side handle. For an MX-5 owner who has no room for a long shop jack, that portability matters as much as the lift numbers. It also suits a track day or autocross bag.
The listed lift range runs from 3-1/2 inches to 14 inches. The low end clears the front of most stock Miatas, though a car on lowering springs or with an added splitter should be measured first. Fourteen inches is enough to pull a wheel or reach a brake caliper on a small car, but it will feel short under a crossover. SATA says every unit is overload tested to 1.5 times its rating before it leaves the factory.
A dual-piston pump raises the saddle to the car in fewer strokes, and the handle has a non-slip rubber grip. The 1.5 ton rating is the limit to respect: this is a jack for the lightest Mazdas, not for a CX-5 or CX-90. Lower the car onto jack stands before any work beneath it.
View SATA 1.5-Ton Hybrid Jack on Amazon
2. VEVOR 1.5 Ton Low Profile Racing Jack: 3.1 in. to 14.4 in. with Dual Pump

- 1.5 ton listed capacity
- 3.1 in. to 14.4 in. lift range
- Steel body with 6 mm aluminum plates
- Large raised rubber saddle pad
VEVOR’s small racing jack pairs a thickened steel body with 6 mm aluminum side plates. That mix keeps it lighter than an all-steel shop jack while giving the frame some stiffness. It sits in the same class as the SATA above, with a slightly lower starting height. The listing gives a minimum of 3.1 inches and a maximum of 14.4 inches.
That low figure is useful on a Miata with a front lip or an older Mazda that has sagged a little on tired springs. The large rubber pad on the saddle spreads the load at the contact point and helps protect a pinch weld or painted surface from scrapes. A dual-pump design brings the saddle up to the car quickly, so you spend less time pumping before the weight starts to come on. Operation is the usual hydraulic routine: close the release valve, pump to lift, then open the valve slowly to lower.
VEVOR’s copy mentions SUVs and pickups, but 1.5 tons is a light rating, and we would keep this jack to small cars such as the MX-5 or a Mazda2. Fourteen inches of lift also limits it to wheel and brake jobs. As with any jack, it is for lifting only, so set the car on stands before reaching under it.
View VEVOR 1.5 Ton Racing Jack on Amazon

3. TONDA 2 Ton Low Profile Jack: 3.35 in. to 13.98 in. Aluminum and Steel Build

- 2 ton (4,000 lb) capacity
- 3.35 in. to 13.98 in. lift range
- Dual pump for faster lifting
- Rubber saddle and 360 degree swivel casters
TONDA’s 2 ton jack steps up the capacity from the 1.5 ton models while staying in the low profile, aluminum and steel category. The listed range starts at 3.35 inches and tops out at 13.98 inches. That makes it a fit for the Mazda3 sedan or hatchback, a Mazda6 and the MX-5, where the jacking points sit low and the cars are not heavy. The extra half ton gives more margin on those mid-size cars.
A dual pump reduces the number of handle strokes it takes to bring the saddle up to the car. The large rubber saddle grips the lift point and keeps bare metal off frame rails and coated underbody parts, which matters on a car you want to keep free of rust. Two swivel casters at the rear let you steer the jack under the car without dragging it sideways across the floor, and a side handle makes it easier to carry.
The 13.98 inch maximum is the main limit. It is enough to get a tire off the ground on a car, but on a CX-5 or CX-50 the saddle may run out of travel before the wheel clears. Keep this one for the cars in a Mazda household and always finish the lift on jack stands.
View TONDA 2 Ton Low Profile Jack on Amazon
4. YELLOW JACKET 3 Ton Extra Long Reach Jack: 3-3/8 in. to 24 in. Lift Range

- 3 ton (6,600 lb) capacity
- 3-3/8 in. to 24 in. lift range
- 33.36 in. steel frame
- Dual-piston quick-lift pump
This YELLOW JACKET jack combines a low starting height with a long steel frame. The listing gives a minimum of 3-3/8 inches and a maximum of 24 inches, so one jack can slide under a Mazda3 or Mazda6 and still raise a CX-5 wheel well clear of the floor. The frame measures 33.36 inches, which helps the saddle reach a central lift point before the handle meets the bumper.
A dual-piston pump brings the saddle up to the car in fewer strokes. The release uses a universal joint system that the maker says gives a smooth, controlled descent, which matters when you are lowering a car onto stands and want it to settle gently. A rubber pad on the saddle protects painted and bare metal under the car, and the handle is wrapped in foam so it is less likely to mark the bodywork if it swings against a panel.
The body is thick industrial steel, so expect a heavy jack that lives in one bay rather than one you carry to the driveway. The 3 ton rating gives a sensible margin on a compact crossover, and the long frame needs floor space when it is stored. Confirm the lift point in your manual, raise the car, then lower it onto jack stands before working underneath.
View YELLOW JACKET 3 Ton Long Reach Jack on Amazon

5. Daytona 3 Ton Long Reach Jack: 3-1/4 in. to 24-1/4 in. with Rapid Pump

- 3 ton capacity
- 3-1/4 in. to 24-1/4 in. lift range
- Dual-piston hydraulic system
- Removable rotating saddle
Daytona’s long reach jack is a full-size steel service jack with a 3 ton rating. The listed lift range is 3-1/4 inches to 24-1/4 inches, which covers a lot of ground in one tool. The low end slides under a Mazda3 or MX-5, and the top end gives real working height under a CX-5, CX-50 or the larger CX-70 and CX-90. For a household with a car and a crossover in the garage, that span is the reason to choose it.
A dual-piston hydraulic system raises the saddle quickly to the lift point. The frame is described as precision-welded steel, and the rear swivel casters run on ball bearings for smoother movement on concrete. The saddle can be removed and rotated, so it accepts lift accessories such as a pinch weld adapter if your model’s jack points call for one.
The trade-off is weight. An all-steel long reach jack is hard to carry and is best kept in one garage bay rather than moved around. It also needs a long clear space in front of the car, because the handle and frame extend well out from the bumper. On the bigger crossovers, lift one corner or end at a time and support the vehicle on stands rated for its weight.
View Daytona 3 Ton Long Reach Jack on Amazon
6. LARBANKE 3 Ton Floor Jack: 5.31 in. to 18.11 in. with Wide Saddle

- 3 ton (6,600 lb) capacity
- 5.31 in. to 18.11 in. lift range
- 4.65 in. diameter saddle
- Carbon steel body with steel casters
LARBANKE’s jack is a straightforward 3 ton steel jack with a lift range of 5.31 to 18.11 inches. The starting height is too tall for an MX-5 or a lowered Mazda3, so this is a crossover jack rather than an all-rounder. Under a CX-5, CX-50 or CX-90, 5.31 inches is rarely a problem, and the extra capacity gives a comfortable margin on the heavier three-row models.
The saddle measures 4.65 inches across, a wide pad that spreads the load on a flat lift point. The body is high-strength carbon steel, and the jack rolls on two large steel casters plus two 360 degree swivel casters. That layout steers easily into position on a smooth garage floor. The listing aims it at tire changes and routine maintenance in a home garage.
Eighteen inches of lift is enough to raise a crossover wheel off the ground, but it is less than the long reach jacks above if you need room to work. LARBANKE does not list a dual-pump or quick-lift feature, so expect more strokes before the saddle meets the car. Use it to lift, then move the weight to jack stands before any work beneath.
View LARBANKE 3 Ton Floor Jack on Amazon
Matching a Jack to Each Mazda Model
Use the table as a shortlist, then confirm with a tape measure. Lowering springs, aero kits and larger wheels all change what fits.
| Jack | Listed lift range | Listed capacity | Mazda match |
|---|---|---|---|
| SATA 1.5-Ton Hybrid | 3-1/2 to 14 in. | 1.5 ton | MX-5 Miata |
| VEVOR 1.5 Ton Racing | 3.1 to 14.4 in. | 1.5 ton | MX-5 with a front lip |
| TONDA 2 Ton | 3.35 to 13.98 in. | 2 ton | MX-5, Mazda3, Mazda6 |
| YELLOW JACKET 3 Ton Long Reach | 3-3/8 to 24 in. | 3 ton | Mazda3, Mazda6, CX-30, CX-5 |
| Daytona 3 Ton Long Reach | 3-1/4 to 24-1/4 in. | 3 ton | Every model from MX-5 to CX-90 |
| LARBANKE 3 Ton | 5.31 to 18.11 in. | 3 ton | CX-5, CX-50, CX-70, CX-90 |
If you own one car and one crossover, a single long reach 3 ton jack covers both, at the cost of weight and floor space. A Miata-only household is better served by one of the light 1.5 ton jacks.

Lifting a Mazda in a Grand Rapids Garage
Follow the same order on every lift.
- Level, solid floor: work on concrete, never on gravel, asphalt on a hot day or a slope.
- Secure the car: set the parking brake, select Park or a gear, turn the engine off and chock the wheel diagonally opposite.
- Place the saddle: line it up with the lift point from your manual, using a pad on a pinch weld.
- Lift and support: raise the car just high enough, then set jack stands for low cars or taller stands for a crossover under the support points.
- Lower onto the stands: open the release valve slowly, then give the car a firm push to check it is steady.
West Michigan winters add their own problems. Salt slush melts off the tires and leaves the floor slippery, so dry the area before you roll a jack in.

A jack and stands are only part of a home setup. Our list of car maintenance tools for beginners covers the wrenches, drain pan and torque wrench that go with them.
When Your Mazda Should Come to Our Shop
A floor jack handles tire swaps and oil changes at home. Some jobs belong on a lift with a trained technician, especially brakes, suspension parts and wheel bearings, where a mistake affects how the car stops and steers.

When the maintenance schedule for your Mazda lists more than you want to tackle on a garage floor, our factory scheduled maintenance service in Grand Rapids handles the full list. For pads, rotors or a soft pedal, book our brake repair in Grand Rapids instead.
More Buying Guides
Frequently Asked Questions
What size floor jack do I need for a Mazda CX-5?
A 3 ton jack with a maximum height of about 18 inches or more suits a CX-5. Check that the minimum height fits under the lift point on your trim.
Will a standard floor jack fit under an MX-5 Miata?
Often not. Many standard jacks start too high for a Miata, so choose a low profile jack that starts around 3 to 3-1/2 inches and measure your car first.
Where do I put the jack on a Mazda?
Use only the lift points shown in your owner’s manual. On a pinch weld, add a slotted rubber pad so the seam is not bent.
Can I work under my Mazda with just the floor jack?
No. A floor jack is for lifting only. Lower the car onto jack stands rated for its weight before any part of your body goes underneath.
Prefer to leave the lifting to someone else? Phone 456 AutoFix at 616-279-3832 between 8am and 5pm, Monday through Friday, or request a visit through our contact page.
If your day runs late, our after-hours drop-off at 456 Carrier St NE in Creston lets you leave the Mazda with us after closing.
