As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A bolt that backs itself out is a small problem until it is a valve cover leak, a rattling heat shield or a loose bracket on the highway. The best threadlocker for cars is the one whose strength matches how often that fastener needs to come apart again.
Below we sort out the colors, explain where threadlocker fits next to grease and epoxy, then go through five picks for the best threadlocker for cars, sorted by strength and job.
Quick answer
Which is the best threadlocker to keep in the garage?
Start with a medium strength blue such as LOCTITE 242, because it holds against vibration yet comes apart with hand tools. Add a red such as LOCTITE 263 only for parts you rarely remove, and consider Permatex orange when a high-vibration bolt needs more grip than blue without heat removal.
Our Quick Picks
Three places to start when choosing the best threadlocker for cars: a medium strength blue for everyday bolts, a removable high strength orange for high-vibration parts and a red for fasteners meant to stay put. All five products are reviewed below.

LOCTITE 242 Blue
The general-purpose blue for fasteners you will service again.

Permatex 25240 Orange
More grip than blue for bolts that still need to come apart.

LOCTITE 263 Red
A heat-removable red for fasteners you rarely take apart.
Blue, Red, Purple, Green: What the Colors Mean
Threadlocker is an anaerobic liquid. It stays wet in the bottle, then cures into a tough plastic once it is trapped between metal threads with no air. The cured film fills the gaps in the threads, so vibration can no longer rotate the fastener, and it also seals out moisture.
Makers use color to signal strength, and the codes are broadly the same across brands:
- Purple (low strength): small screws under about 1/4 inch that you adjust now and then.
- Blue (medium strength): the general choice for bolts you will service, such as valve cover, oil pan and water pump bolts.
- Orange (high strength, removable): a Permatex hybrid meant to hold harder than blue but still come apart with hand tools after some heat.
- Red (high strength): studs and bolts meant to stay put, removed with localized heat.
- Green (wicking): a thin grade that runs into fasteners that are already assembled.
Loctite’s own guide to choosing red or blue threadlocker puts it simply: blue is made to be removed with common tools, while red is the more permanent fix. When you are unsure, pick the weaker grade that will still hold.
Threadlocker vs Grease, Anti-Seize and Epoxy
These products get mixed up because they all go on threads, but they do opposite jobs. Threadlocker is there to stop a fastener from turning. Grease and anti-seize are there to help it turn, either while you torque it or years later when you need it out.
Anti-seize suits spark plugs, exhaust studs and other hot, rust-prone threads where seizing is the bigger risk, and our anti-seize compound picks cover that side. Never put both on the same thread. If a bolt is already rusted solid, soak it first with something from our penetrating oil buying guide before you reach for a breaker bar.
Epoxy is a structural glue that is not designed to be undone, so on a car fastener you may need to remove one day, threadlocker is the better tool. Sealing a flange or a pan rail is a third job again, handled by a gasket maker from our RTV gasket maker roundup.
Best Threadlocker for Cars: The Picks in Detail
These five run from a purple for tiny screws to a red for parts meant to stay put, in liquid and stick form. Check the label and your service manual before any of them goes on a car fastener.
1. LOCTITE 242 Automotive Blue: 36 ml Medium Strength Threadlocker for All Metals

- Medium strength, removable with hand tools
- Works on all metals, including stainless and aluminum
- Begins setting in 5 minutes, full strength in 24 hours
- Listed for valve cover, oil pan and water pump bolts
LOCTITE 242 is the medium strength blue threadlocker most people picture when they hear the brand name, sold here in the automotive 36 ml bottle. It is an anaerobic liquid that cures once it is trapped between metal threads, locking the fastener against loosening from vibration while still letting you remove it later with ordinary hand tools.
The listing says it works on all metals, including passive surfaces such as stainless steel, aluminum and plated hardware, which covers most of what you meet under a hood. Loctite lists typical uses as valve cover bolts, water pump bolts, oil pan bolts, drive shaft bolts, rocker arm adjustment nuts and carburetor studs. It starts to set in about 5 minutes and reaches full strength after 24 hours, so you have a short window to assemble and torque the part.
This is the one to buy first if you only want a single bottle in the garage. It suits the fasteners you expect to undo again at the next service. It is too strong for tiny screws, which can strip before the bond breaks, and it is not meant for parts that should stay permanently locked, where a red is the better fit.
View LOCTITE 242 Blue on Amazon
2. LOCTITE 248 Blue Threadlocker Stick: 9 g Medium Strength, No Drip Semi-Solid

- Medium strength in a twist-up wax stick
- Drip-proof and melt-resistant for overhead bolts
- For threads from 6 to 19 mm (1/4 to 3/4 in)
- Sets in 10 minutes, full cure in 24 hours
LOCTITE 248 delivers medium strength blue threadlocker in a semi-solid stick that twists up like a glue stick. You rub it onto the threads instead of dripping a liquid, which makes it tidy to use on bolts that point upward, sideways or sit somewhere awkward under the car.
The listing describes the stick as drip-proof, leak-proof and melt-resistant, and says it tolerates minor oil contamination from motor oil, corrosion protection oils and cutting fluids. It is rated for threads from 6 to 19 mm (1/4 to 3/4 inch). Suggested uses include valve cover bolts, water pump bolts, oil pan bolts, rocker studs, caliper brackets and cylinder head hardware. It sets in about 10 minutes and fully cures within 24 hours.
The stick format suits a toolbox or a roadside kit, since there is no bottle to tip over or leak. It is also easy to pre-coat several bolts on a bench before an install. Strength is in the same class as a blue liquid, so it shares the same limits: it is not a substitute for red on parts that should stay locked, and the small 9 g size runs out quicker on large bolts.
View LOCTITE 248 Stick on Amazon

3. Permatex 25240 Orange: 36 ml High Strength Removable Threadlocker for High Vibration

- Hybrid: red-level hold, blue-style serviceability
- Listed at 3x the holding power of standard blue
- For fasteners 1/4 to 1 in (6 to 25 mm)
- Remove with localized heat and hand tools
Permatex 25240 is an orange threadlocker that sits between the usual blue and red grades. Permatex calls it a hybrid formula that combines the holding strength of its red threadlocker with the serviceability of its blue, and it is sold in a 36 ml bottle.
According to the listing, it gives three times the holding power of standard blue threadlocker on fasteners from 1/4 to 1 inch (6 to 25 mm), and it is meant to resist loosening from shock and vibration. Permatex suggests flywheel bolts, axle nuts, transmission mounts and similar heavy-duty hardware. To apply, you clean and dry the threads, add a few drops at the engagement area and assemble. To take it apart, Permatex says to apply localized heat and then remove the fastener with standard hand tools.
This makes sense for a bolt that keeps working loose under blue but that you still expect to remove one day, such as a mount or a bracket on a vehicle that sees rough roads. It is more than most everyday jobs need. For routine engine bolts a blue is easier to live with, and for parts that never come off a red is the clearer choice.
View Permatex 25240 Orange on Amazon
4. LOCTITE 263 Automotive Red: 36 ml High Strength, Oil Tolerant Threadlocker

- High strength for heavy shock and vibration
- Oil tolerant, works on as-received fasteners
- For fasteners up to 1 in (25 mm)
- Fluorescent, removable with localized heat
LOCTITE 263 is a high strength red threadlocker in the automotive 36 ml bottle. It is the grade for fasteners you do not plan to remove often, where vibration, shock or harsh conditions could otherwise loosen them over time.
The listing highlights strong oil tolerance, so it can bond on fasteners that are not perfectly clean, and says it works on all metals including stainless steel, aluminum and plated parts. It is listed for fasteners up to 1 inch (25 mm), and Loctite gives cylinder block bolts, ring gear bolts and transmission shaft bolts as typical uses. The formula is fluorescent, which helps confirm under a UV light that it was applied. It begins setting in about 10 minutes and reaches full strength after 24 hours.
Removal calls for localized heat and then hand tools, so think before using it on anything you service regularly. It suits studs, fasteners on equipment you seldom open and bolts that keep backing out under blue. Keep it away from small screws, which can break before the bond releases. As with any threadlocker, follow the vehicle maker’s torque figure and instructions for the specific fastener.
View LOCTITE 263 Red on Amazon

5. LOCTITE 222 Purple: 6 ml Low Strength Threadlocker for Small Screws

- Low strength for fasteners under 1/4 in (6 mm)
- Removable with hand tools
- Non-corrosive formula
- Sets in 20 minutes, full strength in 24 hours
LOCTITE 222 is a low strength purple threadlocker in a small 6 ml tube. It is made for fasteners under 1/4 inch (6 mm), where a blue or red product could hold so firmly that the screw head strips or the screw snaps before it comes out.
The listing says it locks and seals fasteners against loosening from vibration, remains easy to remove with hand tools and uses a non-corrosive formula. Loctite lists carburetors, relay locks, headlamps, throttle body assemblies, choke assemblies and fuel injection set screws as typical uses. It starts to set in about 20 minutes, a longer working time than the blue and red grades, and reaches full strength after 24 hours.
This tube is for small adjusters and screws you may need to reset, which also makes it the usual pick for hobby work such as RC cars with metal threads. The 6 ml size is plenty for small screws but runs out fast on anything larger. It does not have the strength for medium or large bolts, and it is not listed for plastic threads, so check the label before using it near plastic housings.
View LOCTITE 222 Purple on Amazon
The Best Threadlocker for Each Type of Bolt
Use this table as a starting point, then let the vehicle maker’s instructions override it. Some factory bolts specify a particular product or a pre-applied patch.
| Fastener | Strength | Removal | Picks that fit |
|---|---|---|---|
| Small screws, throttle body and trim screws | Low (purple) | Hand tools | LOCTITE 222 |
| Valve cover, oil pan, water pump and bracket bolts | Medium (blue) | Hand tools | LOCTITE 242, LOCTITE 248 stick |
| High-vibration bolts you still service | High, removable (orange) | Localized heat, then hand tools | Permatex 25240 |
| Studs and bolts meant to stay put | High (red) | Localized heat | LOCTITE 263 |
A good torque wrench matters as much as the product. Threadlocker can change how a bolt reaches its clamping force, so follow the torque figure and any threadlocker note in the vehicle maker’s procedure. Our torque wrench guide for DIY work covers the clicker and digital options.

How to Use Threadlocker and How to Break It Loose
The routine is the same for every color:
- Clean the threads: even the best threadlocker for cars bonds poorly on dirty threads, so brush out old residue and remove oil unless the label says it tolerates some.
- Apply a few drops: put them where the nut or hole will engage, not on the first thread or the whole bolt.
- Assemble and torque: tighten to the maker’s spec straight away, before the product starts to set.
- Give it time: most products set within minutes and reach full strength in about 24 hours.
To take a blue joint apart, use normal hand tools; the bond lets go with a firm, steady pull. For red, orange or green, the makers call for localized heat on the fastener before you turn it, then removal while it is still warm. Keep the flame or heat gun well away from fuel lines, brake lines, wiring, rubber and plastic.
Clean the old film off both threads before you reassemble with fresh product, since leftover cured material can upset the next torque reading.

Road Salt, Rust and Threads in West Michigan
Winter salt and freeze-thaw cycles push moisture into every exposed thread under a car. Threadlocker fills the gaps between the threads, so it also helps seal out that moisture, but that is a bonus, not a reason to put it on everything.
Underbody fasteners that see heat or need regular removal, such as exhaust hardware, often call for anti-seize instead. If you are working near the oil pan during an oil change, the same blue that suits the pan bolts is worth having on the shelf, and our synthetic oil comparison helps with the refill. Small screws on a throttle body are a purple job, and cleaning that area is a good moment to read our fuel system cleaner guide.
When a Loose Bolt Needs a Mechanic
Some loose fasteners point to a bigger problem, and the best threadlocker for cars will not fix a bolt that was torqued wrong. Brake caliper bracket bolts, suspension bolts and steering components have specific torque values and, on many cars, specific instructions about pre-applied locking patches or one-time-use hardware. Getting those wrong is a safety issue, so follow the factory procedure or hand the job to our brake repair team in Grand Rapids.

An oil drip from a pan or valve cover that keeps coming back after you snug the bolts usually means a tired gasket, not a loose thread. We can look at it during an oil change in Creston and tell you whether a reseal is due. Hendrick Hoffman, our ASE certified owner and head mechanic, has worked on foreign and domestic cars since 2005.
More Buying Guides
Frequently Asked Questions
Is threadlocker permanent?
Only the high strength grades come close. Purple and blue are designed to come apart with ordinary hand tools, while red and green usually need localized heat before the fastener will turn. Even red is removable that way, so “permanent” really means you should not expect to undo it casually.
Is threadlocker necessary on every bolt?
No. Most car fasteners hold on correct torque alone, and some must stay dry or use anti-seize. Use threadlocker where the vehicle maker calls for it or where a bolt has a history of working loose from vibration.
What is the difference between threadlocker and Loctite?
Threadlocker is the product type, and Loctite is a brand that makes several threadlockers along with other adhesives. Permatex and Vibra-TITE make threadlockers too, with similar color codes for strength.
What is the best threadlocker for RC cars?
RC cars use small screws, often into aluminum or plastic parts, so a low strength purple such as LOCTITE 222 is the usual match for metal threads. Blue can make tiny screws hard to remove, and plastic parts need a product listed as plastic safe.
Bolt keeps loosening, or a leak keeps coming back? Ring 456 AutoFix on 616-279-3832 any weekday from 8am to 5pm, or send us a booking request and we will find the cause.
Short on daytime hours? Our after-hours drop-off lets you bring the car to 456 Carrier St NE when it suits you; leave a note saying which bolt or leak has been giving you trouble.
