As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
An engine on the floor is a problem, and an engine on a shaky stand is a bigger one. The best engine stand for your garage holds the block at a comfortable height, turns it over without a fight and folds away when the project waits for parts.
Below: how a stand differs from a hoist or cradle, what to check, and six stands from simple four-arm models to geared and heavy-duty frames. Pulling the engine first? Start with our guide to the best engine hoist, because the two tools work as a pair.
Quick answer
Which engine stand suits a home garage?
For a four-cylinder or small V8, a 1,000 to 1,250 lb rotating stand such as the BIG RED T25671 does the job. If you rebuild heavy engines alone, a geared head like the Sunex 8300GB turns the load with a crank. Big diesels and dressed iron V8s call for a 2,000 lb frame.
Our Quick Picks
Three starting points: a simple rotating stand for everyday rebuilds, a geared stand for turning heavy engines alone and a 2,000 lb frame for diesels. All six stands are reviewed below.

BIG RED T25671
A straightforward four-arm stand with a tray that keeps bolts and sockets off the floor.

Sunex 8300GB
A crank-turned, self-locking head lets one person roll an engine slowly and stop anywhere.

GarveeTech 2000 LBS
A wide base and a 2,000 lb rating for diesels and big blocks.
Engine Stand or Hoist? Stand vs Cradle vs Cherry Picker
A hoist, also called an engine lift or cherry picker, raises the engine out of the bay and lowers it somewhere; a stand bolts to the back of the block and holds it while you work.
- Engine hoist: lifting and moving only, not holding an engine for days.
- Engine stand: a mounting head with adjustable arms bolts to the bellhousing face, and the head rotates so you can reach the bottom end, heads and timing cover.
- Engine cradle or dolly: supports the engine by its mounts or pan rails at floor level, with no rotation.
For most engine pulls you need both. The hoist sets the engine onto the stand, then goes back in the corner.
What Separates a Solid Stand From a Wobbly One
Four details decide whether the best engine stand for your project feels planted or nervous once the engine hangs off it.
- Capacity with margin: the rating assumes the engine’s weight sits close to the mounting head. A dressed engine hangs further out, so pick a rating well above its weight.
- Head type: a simple head rotates freely and locks with a pin, so you steady the engine by hand while turning it. A geared head uses a worm gear and crank and holds itself in place.
- Base and casters: wide H- or U-shaped bases and more casters resist tipping.
- Arms and hardware: check the arm spread on the listing against your engine’s bellhousing bolt pattern, and expect to buy the right bolts separately.
Tools like these only stay safe when they are used and maintained properly, a point OSHA’s hand and power tool safety guidance makes for every shop tool. Check welds, the head pin and casters before each use.
Best Engine Stand Picks, One at a Time
Capacities and features come from each maker’s Amazon listing. Engine-specific bolts are usually not included.
1. BIG RED T25671 Torin: 1,250 lb Rotating Engine Stand with Tool Tray

- 5/8 ton (1,250 lb) stated capacity
- 360-degree rotating mounting head
- Four adjustable mounting arms
- Front swivel casters and tool storage tray
The BIG RED T25671 from Torin is the plain, familiar type of engine stand that turns up in a lot of home garages. Torin rates it at 5/8 ton, or 1,250 lb, and it uses a mounting head with four adjustable arms that bolt to the back of the block. The head rotates through a full 360 degrees, so you can roll the engine over to reach the crankshaft, oil pump and timing cover without lifting it again.
The listing describes a frame designed to resist tipping, with swivel casters at the front so you can steer the stand and position the engine where the light is good. A built-in tool storage tray holds fasteners, sockets and small parts, which helps when a teardown spreads across a weekend. The rotating head locks with a pin, so keep one hand on the engine as you turn it and let the weight settle before you let go.
This stand suits four-cylinder engines, V6 units and small V8 engines, especially once the intake and accessories are off. Builders who work alone on dressed iron V8s or diesels will find a geared head or a higher rating easier and steadier. Bolts for your engine are not part of the listing, so buy the correct size and grade separately.
2. SUNEX 8300GB: 1/2 Ton Foldable Engine Stand with 63:1 Worm Drive Gearbox

- 1/2 ton stated capacity
- 63:1 worm drive gearbox with crank handle
- Self-locking head holds the engine at any angle
- Folds for storage, locking ball-bearing casters
The Sunex 8300GB is a geared engine stand, and that gearbox is the main reason to pick it. Instead of a free-turning head that you steady by hand, Sunex fits a 63 to 1 worm drive gearbox. You turn a crank handle and the engine rolls slowly, and the self-locking design holds it in whatever position you stop at.
That matters most when the engine is top-heavy or still carries its heads and intake. With a pin-lock head, a heavy engine can swing hard toward its low side the moment you pull the pin, while a worm gear simply stops. Sunex states the stand handles and positions virtually all automotive engines, and it is rated at 1/2 ton. The frame folds for storage, and the ball-bearing swivel casters have safety locks to keep the stand from rolling while you work.
The 8300GB suits anyone who rebuilds engines alone, does machine-shop prep or turns an engine often during assembly. Its half-ton rating covers most car engines, but very heavy diesels and fully dressed big blocks want more margin. As with any stand, confirm the arm reach against your bellhousing bolt pattern and use high-strength bolts that match your block.

3. Omega Pro OP0960S: 1,250 lb Folding Engine Stand with 6 Casters

- 1,250 lb stated capacity
- Folding frame for storage
- Six casters on an extra-wide base
- Mounting arms adjust from 7-1/2 to 10-1/2 inches
The Omega Pro OP0960S is a folding engine stand rated at 1,250 lb, built from welded square tubular steel with a rust-resistant finish. Omega lists an extra-wide base for stability, and six casters spread the load so the stand rolls smoothly across a shop floor. When the engine comes off, a quick-folding mechanism lets you stand the frame against a wall instead of tripping over it.
The mounting head carries four adjustable arms with 360-degree rotation, and Omega gives the arm range as 7-1/2 to 10-1/2 inches. That figure is handy because you can compare it with your engine’s bellhousing bolt spacing before you order. The listing also gives an overall height of 42-3/4 inches, base dimensions of 41-3/4 by 23-5/8 inches and 3-1/2 inch wheels, so you can plan where it will live in the garage.
This stand suits a one-car or shared garage where floor space returns to the family car once the engine is done. Its capacity covers most four-cylinder, V6 and small V8 engines with room to spare. The head turns freely rather than through a gear, so it is less relaxed for one person rolling a heavy, fully dressed engine on their own.
View Omega Pro OP0960S on Amazon
4. Eastwood EZ Turn: 1,000 lb Portable Engine Stand with 63:1 Worm Gear

- Supports up to 1,000 lb
- 63:1 ratio worm gear drive
- 360-degree rotating head
- Locking swivel casters, 67.2 lb assembled weight
The Eastwood EZ Turn brings geared rotation to a lighter, more portable stand. Eastwood lists a 63 to 1 ratio worm gear drive, so turning the engine is a matter of cranking a handle rather than wrestling the block around. The head rotates a full 360 degrees and the listing gives a capacity of up to 1,000 lb.
Eastwood states an assembled weight of 67.2 lb, and the stand rides on two stationary and two swivel steel ball-bearing casters, with locking casters to hold it in place. That lighter frame makes it easier to move around the garage or put away between projects than a heavier shop stand. The geared head is helpful when you are fitting a rear main seal, setting up the timing or checking bearing clearances and want the engine to stop exactly where you leave it.
This stand suits four-cylinder engines, smaller V6 and V8 engines and classic car restorations where the engine is stripped before it goes on. With a 1,000 lb rating, it is not the choice for diesels or a big block that still has its heads, intake and manifolds fitted. Check the arm spread against your block and buy the right bolts for your engine separately.
View Eastwood EZ Turn on Amazon

5. Big RED AT37912-2 Torin: 1,500 lb Folding Engine Stand with H Base

- 3/4 ton (1,500 lb) stated capacity, ASME tested per listing
- Upgraded H-shaped base
- Four adjustable arms with 2.16 in hex head bolts
- Three 360-degree casters, two with brakes, folding frame
The Big RED AT37912-2 is Torin’s step up from the basic four-arm stand. It carries a 3/4 ton, or 1,500 lb, rating, and the listing says it has undergone ASME testing to support that load. The frame uses an upgraded H-shaped base, which Torin describes as reducing shaking and tilting compared with older designs.
The mounting head has four adjustable arms with 2.16 inch hex head bolts on the arms and rotates through 360 degrees, so you can reach any side of the block. Torin states it holds most foreign and domestic engine blocks. Three 360-degree casters move the stand, two of them with brakes, and the frame folds when the job is finished so it takes up less of the garage.
The extra capacity is the reason to choose this model over a 1,000 or 1,250 lb stand. An iron-block V8 with its heads, intake and accessories still bolted on puts more leverage on the head than a bare short block, and this stand leaves more margin for that. The head turns freely rather than through a gear, so steady the engine by hand as you rotate it, and lock the casters before you start loosening anything tight.
View Big RED AT37912-2 on Amazon
6. GarveeTech Engine Stand: 2,000 lb Foldable Stand with 6 Casters

- 2,000 lb stated capacity
- U/H-type base with reinforced steel neck
- Four adjustable arms on a 360-degree head
- Six steel bearing casters, folding frame
The GarveeTech engine stand is the heavy option in this list, with a stated capacity of 2,000 lb. GarveeTech uses a U/H-type base rather than a traditional T-shaped base and a reinforced steel neck to support the mounting head. The aim is a stand that stays steady with a large engine hanging off one side.
The mounting head has four adjustable arms and rotates 360 degrees, and the listing mentions 1.1 inch hex head bolts and a 15 inch handle for turning the engine. Six industrial-grade steel bearing casters swivel a full 360 degrees for moving the load around the shop. When the engine is back in the vehicle, the frame folds so it can be stored against a wall or in a corner.
This stand suits diesel engines, big-block V8s and anyone who likes to work with the engine still dressed, where a lighter stand would be close to its limit. The head is not geared, so rotating a heavy engine calls for care and ideally a second pair of hands. For a small four-cylinder it is more frame than you need, and a lighter folding stand will be easier to handle and store.
View GarveeTech 2000 LBS on Amazon
The Six Stands Side by Side
Ratings are the makers’ stated capacities; treat them as a ceiling, not a target.
| Stand | Stated capacity | Head and frame | Suits |
|---|---|---|---|
| BIG RED T25671 | 1,250 lb | Free-turning head, tool tray | Four-cylinder and small V8 rebuilds |
| Sunex 8300GB | 1/2 ton | 63:1 geared head, folds | Solo builders turning complete engines |
| Omega Pro OP0960S | 1,250 lb | Free-turning head, folds, 6 casters | Small garages that need floor space back |
| Eastwood EZ Turn | 1,000 lb | 63:1 worm gear, locking casters | Lighter engines and restoration work |
| Big RED AT37912-2 | 1,500 lb | H base, folds, 3 casters | Iron-block V8s with accessories on |
| GarveeTech 2000 LBS | 2,000 lb | U/H base, folds, 6 casters | Diesels and big-block builds |

If two stands look equal on paper, the best engine stand of the pair is the one with the wider base and better casters. You will roll the engine around more often than you expect.
Bolts, LS Swaps and K24 Builds
The bolts matter as much as the stand. Match the thread size and pitch of your block’s bellhousing holes, use high-strength bolts long enough for full thread engagement, and add flat washers under the arms; many builders buy Grade 8 or class 10.9 hardware for this.
Shopping for the best engine stand for an LS? Check that the arms reach the bolt pattern without hitting the rear crankshaft flange, and use spacers if they do. For the best engine stand for a K24 or another compact four-cylinder, any stand here has plenty of capacity; arm reach on a small block face is the thing to confirm on the listing.

Tighten the mounting bolts evenly and recheck them after the first rotation; a torque wrench for mechanics helps here and during reassembly.
Winter Projects in an Unheated Garage, and When to Call Us
Plenty of West Michigan engine projects sit on a stand from November until spring. Cold, damp garages rust bare cylinder walls and machined surfaces fast, so fog them with oil, bag the engine and plug every open port.
Before the car goes up, set it on jack stands rated for home garage work and lift it with a shop-grade floor jack. A full mechanic tool set covers the teardown.

Missed service intervals cause much of the wear that leads to an engine pull, and our factory scheduled maintenance in Grand Rapids keeps the oil, belts and fluids on the maker’s schedule. Dropping a transmission too? See our transmission jack guide.
More Buying Guides
Frequently Asked Questions
Do I need an engine stand and a hoist?
For most engine pulls, yes. The hoist lifts the engine out of the car and onto the stand, and the stand holds it at working height so you can rotate it while you tear down or rebuild.
What is the difference between an engine cradle and an engine stand?
A cradle supports the engine from below by its mounts or pan rails and keeps it low for storage or moving. A stand bolts to the bellhousing face and rotates, which is what you want for a teardown or rebuild.
What bolts should I use on an engine stand?
Use high-strength bolts that match the thread size and pitch of your block’s bellhousing holes, long enough for full thread engagement, with flat washers. Many builders choose Grade 8 or class 10.9 hardware and keep a dedicated set for the stand.
Is a geared engine stand worth it?
If you work alone on heavy or top-heavy engines, it usually is. A worm gear lets you turn the engine slowly with a crank and holds it at any angle, while a pin-lock head needs a hand on the engine as it turns.
Got a car that needs work you’d rather not tackle on the garage floor? Ring 456 AutoFix on 616-279-3832, Monday to Friday from 8am to 5pm, or reach us through the contact page and we’ll find a slot.
Can’t get away during the workday? Our after-hours drop-off is there for that. You’ll find us at 456 Carrier St NE, Grand Rapids, MI 49505.
