As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
Plenty of modern sedans and sports cars sit so low at the front that a regular garage jack hits the bumper cover before the saddle gets anywhere near a lift point. The best low profile floor jack for cars like these is one whose saddle starts low enough to slide in, then still rises high enough to set a pair of stands underneath.
Below: how to measure your gap, aluminum versus steel, and six low-profile jacks. If you are building a home garage from scratch, start with our starter list of car maintenance tools for beginners, which shows where a jack fits in the kit.
Quick answer
Which low profile floor jack suits a low car?
Pick a jack whose listed minimum height is below the lowest point ahead of your lift point, with a maximum height that clears your jack stands. The Arcan A20019 is a light aluminum 3 ton option, the Powerbuilt 240076 starts at 3 inches, and the Sunex 6602LP starts at 2.75 inches with a long reach.
Our Quick Picks
Three jacks that cover the main needs: a light aluminum unit, a steel jack with a wide lift range, and an ultra-low jack with long reach.

ARCAN A20019
An aluminum jack that is easy to move around the garage or driveway.

Powerbuilt 240076
A steel jack that starts low and still lifts taller vehicles.

Sunex 6602LP
The lowest start and the tallest top of the six.
Measure the Gap Before You Shop
Low profile is a number, not a style. Every listing gives a minimum saddle height, and that figure has to be lower than whatever sits in the jack’s path: the front lip, a side skirt or the underbody tray. Measure from the floor to the lowest point the jack has to pass under, not just at the jack point itself.
Then check three more things. Reach matters because a short chassis may run out of length before the saddle gets to a center lift point. Maximum height matters because the car has to go up far enough for a jack stand to slide in at a working height. Capacity matters least, since you lift one corner or one end at a time.
Some jacks, such as the GearWrench below, state that they meet ASME PASE, the ASME safety standard for portable automotive service equipment that covers garage jacks and stands. It is worth looking for on the box or listing, though it never replaces jack stands.
Aluminum Frame or Steel Frame?
Aluminum jacks are lighter, so they are easier to carry to the driveway, the track or the trunk of a second car. Steel jacks weigh more and usually cost less for the same capacity, and the weight helps them stay planted while you pump. Hybrid designs use aluminum side plates with a steel lift arm or the other way around.
For a jack that lives on one garage floor, steel is a sensible default. Either way, the listed heights matter more than the metal.
Best Low Profile Floor Jack for Cars: Six Picks in Detail
All of the specs below come from each jack’s Amazon listing. Compare each minimum height with the measurement you took under your own car.
1. ARCAN A20019: 3 Ton Aluminum Low Profile Floor Jack with Quick Rise

- 3 ton (6,000 lb.) capacity
- 3.75 in. minimum, 18 in. maximum height
- Aircraft-grade aluminum frame
- Bypass and overload valves
The Arcan A20019 is a 3 ton floor jack built around an aluminum frame, which the listing describes as aircraft-grade. That material keeps the weight down compared with an all-steel jack of the same rating, so it is easier to lift into a trunk, carry across the driveway or roll from one bay to another. The listing quotes a 6,000 lb. capacity for passenger cars, SUVs and light trucks.
Its saddle starts at 3.75 inches and rises to 18 inches. That opening height clears many sedans and coupes with ordinary front lips, while 18 inches at the top is enough to set typical jack stands at a working height on most cars. Arcan lists a quick-rise feature that brings the saddle up to the load quickly, a reinforced lift arm for torsion control, and bypass and overload valves that stop the jack from over-extending or lifting past its rating.
A side-mount handle helps when you have to angle the jack in from the side rather than straight on. It suits someone who wants a light jack with real capacity and a respectable lift range. It is not the lowest jack here, so a car with a very low air dam may need the Sunex or Powerbuilt instead, and you still need jack stands for any work underneath.
2. BIG RED T815016L Torin: 1.5 Ton Aluminum and Steel Racing Floor Jack

- 1.5 ton (3,000 lb) capacity
- 3.5 in. to 14 in. lifting range
- Dual piston quick lift pump
- Foam handle bumper and side carry handle
The Big Red T815016L from Torin is a compact racing-style floor jack that mixes aluminum and steel in its construction. It carries a 1.5 ton, or 3,000 lb, rating, which is modest on paper but enough for lifting one corner or one end of most small and midsize cars. The listing says it suits general or specialty use, and the small footprint makes it easy to store on a shelf or in a trunk.
Its lifting range runs from 3.5 inches to 14 inches. The low start lets it slip under many low cars, and the dual piston quick lift pump helps the saddle reach the car in fewer strokes. A side handle makes it simple to carry, the main handle is knurled for grip, and a foam bumper on the handle helps protect the bumper cover and paint if the handle swings into the car.
The limit to keep in mind is the 14 inch top height. That suits wheel changes and quick brake checks, but on some cars it may not raise the body enough to set jack stands at a comfortable height for longer jobs. Think of it as a portable second jack or a track tool rather than the only jack in a home garage.
View Big Red T815016L on Amazon

3. Powerbuilt 240076: 2.5 Ton Low Profile Floor Jack with Dual Piston Fast Lift

- 2.5 ton capacity
- 3 in. minimum, 19-1/2 in. maximum height
- Reaches full height in 7 handle pumps
- Foot pump for fine saddle positioning
The Powerbuilt 240076 is a 2.5 ton steel floor jack aimed at both home garages and repair shops. Its listing gives a 3 inch minimum height, which gets it under many lowered or sport-oriented cars, and a 19-1/2 inch maximum, which reaches the lift points on pickups and SUVs. That spread makes it a practical choice for a household with one low car and one tall one.
Powerbuilt says the dual piston pump raises the lift arm to its full height in 7 handle pumps, so you spend less time pumping before the saddle meets the car. A foot pump adds small, controlled adjustments while you line up the saddle with your hands free. The frame is flanged steel with a wide wheelbase and a large saddle, which the listing credits with balance and stability during a lift.
Because it is steel, it is heavier to carry than the aluminum jacks here, so it fits best in a garage where it rolls rather than travels. It suits drivers who want low entry and real height in one tool. As with any jack on this list, set the car on stands at the maker’s lift points before you work under it.
View Powerbuilt 240076 on Amazon
4. Daytona 3 Ton Steel Low Profile Floor Jack: Dual Piston Rapid Pump

- 3 ton lift capacity
- 3-1/4 in. to 20 in. lift height
- Precision-welded steel construction
- Ball bearing rear swivel casters
This Daytona 3 ton jack is a full-size steel service jack with a low-profile front. The listing gives a lift height of 3-1/4 inches to 20 inches, which covers low cars at the bottom end and trucks or SUVs at the top. That 20 inch ceiling is among the taller ones in this guide, which helps when you want room for stands set high enough to work under the car comfortably.
The hydraulic unit uses a dual piston pump, which Daytona markets as Rapid Pump, to bring the saddle up to the load quickly. The listing describes the frame as precision-welded steel with rust-resistant hardware, and ball bearing rear swivel casters let the jack turn in place as you steer it under the car. This listing is the black version; Daytona also sells a blue one with the same stated lift range.
As a steel 3 ton jack it is heavy, so it suits a garage floor rather than the trunk. It is a good match for someone who wants one jack for a low car and a family SUV and doesn’t need to carry it around. Check the minimum height against your car’s front lip, and always support the car on stands before going under.
View Daytona 3 Ton Low Profile on Amazon

5. SUNEX TOOLS 6602LP: 2 Ton Low Rider Steel Service Jack with 2.75 in. Minimum

- 2.75 in. minimum, 24 in. maximum height
- Dual pump pistons, full height in 6.5 pumps
- 18 in. throw for long reach
- Low chassis profile along its full length
The Sunex 6602LP Low Rider is a 2 ton steel service jack built for very low vehicles. Its listing gives a 2.75 inch minimum height, the lowest in this guide, and Sunex names sports cars, exotic cars and cars with a flat tire as the targets. A flat tire drops a corner closer to the ground, so a jack that starts this low can save you from digging for clearance.
At the other end it rises to 24 inches, which is tall enough for pickups and SUVs. The listing describes an 18 inch throw that reaches lift points well under the car, and notes that the low profile runs the whole length of the chassis rather than only at the nose. That matters on cars where the skirt or underbody tray is low all the way back to the jack point. Dual pump pistons take the saddle to full height in 6.5 pumps.
The trade-off is size and weight: a long steel chassis takes up floor space and is not something to carry far. It suits owners of genuinely low cars who also want enough height for stands. Lift only at the maker’s points shown in the owner’s manual, and lower the car onto stands before working under it.
6. GEARWRENCH GWLPFJ3T: 3.5 Ton Low Profile Long Arm Floor Jack

- 3.5 ton capacity
- Low profile, long arm design
- Dual piston fast lift system
- Meets ASME PASE-2019 requirements
The GearWrench GWLPFJ3T is a 3.5 ton floor jack, the highest rating among the six jacks here. GearWrench is a hand tool brand many mechanics already know, and this jack brings that name to garage lifting gear. The listing describes a low profile, long arm design aimed at vehicles with little ground clearance, so it can reach in under a low front and still get to a lift point set well back.
A dual piston fast lift system raises the saddle with steady, consistent force. The handle has a protected design meant to avoid marking the car if it touches the body, and the saddle has a rubber pad that grips the lift point and helps prevent damage to the frame or pinch weld. The listing also states that the jack meets the ASME PASE-2019 safety and performance requirements for portable automotive service equipment.
The Amazon listing does not give minimum or maximum heights, so check the current product details or the maker’s spec sheet before you buy and compare them with your car. It suits someone who works on heavier sedans and wagons as well as low cars, and who values the extra capacity. Jack stands are still a must whenever you go underneath.
View GearWrench GWLPFJ3T on Amazon
The Six Jacks Side by Side
Use this as a shortlist. A dash means the listing doesn’t state that figure.
| Jack | Capacity and frame | Listed lift range | Good fit for |
|---|---|---|---|
| Arcan A20019 | 3 ton, aluminum | 3.75 to 18 in. | A light jack you carry around |
| Big Red T815016L | 1.5 ton, aluminum and steel | 3.5 to 14 in. | Quick wheel swaps on small cars |
| Powerbuilt 240076 | 2.5 ton, steel | 3 to 19.5 in. | Low cars and taller vehicles in one garage |
| Daytona 3 ton | 3 ton, steel | 3.25 to 20 in. | An everyday steel garage jack |
| Sunex 6602LP | 2 ton, steel | 2.75 to 24 in. | Very low cars and long reach |
| GearWrench GWLPFJ3T | 3.5 ton | – | Heavier cars, PASE-2019 listed |
If two jacks both clear your car, choose on maximum height and reach next. A jack that tops out around 14 inches is fine for a tire change, but on many cars it won’t lift high enough to get a stand under a pinch weld at a comfortable working height.

Lifting a Low Car Safely in a Michigan Garage
A floor jack is a lifting tool, not a support. Raise the car at the maker’s jack point, set rated jack stands on solid, level concrete, and lower the car onto the stands before any part of you goes underneath. Never work under a car held only by a jack, however steady it feels.
- Chock the wheels that stay on the ground and set the parking brake.
- Keep jacks and stands off asphalt on hot days and off cracked or icy slabs.
- Lower the car slowly with the release valve, and keep your feet clear of the handle.
- When the wheel goes back on, torque the lug nuts to the owner’s manual spec in a star pattern.

West Michigan winters add a twist. Years of road salt eat at pinch welds and jack points, so look at the metal before you lift and skip any spot that is flaking or soft. For setting those lug nuts back up, see our guide to torque wrenches for lug nuts.
When a Shop Lift Makes More Sense
A low profile jack handles tire swaps, brake inspections and oil changes on most cars. Some jobs are easier and safer on a two-post lift, especially work that needs the whole car level and high, or a suspension job where the arm has to be loaded. If a lift point looks rusted through, have it checked before you jack the car at home again.

When the car is due for its next service interval, our factory scheduled maintenance service in Grand Rapids covers the checks in your owner’s manual on a lift. If you noticed a clunk or a worn bushing while the car was up, our suspension repair service can take a closer look.
More Buying Guides
Frequently Asked Questions
What minimum height counts as low profile?
There is no fixed cutoff, but the jacks in this guide list minimum heights from 2.75 to 3.75 inches. What matters is that the number sits below the lowest point under your own car, so measure before you buy.
Is a 1.5 ton jack enough for a car?
For lifting one corner or one end of a small car, often yes, but check the maximum height too. Compact racing jacks can top out low enough that getting a jack stand under the car becomes hard.
Do I still need jack stands with a good floor jack?
Yes. A hydraulic jack can leak down or slip, so always lower the car onto rated jack stands on solid ground before you reach or crawl underneath.
Where should I place a low profile jack on my car?
Only at the lift points shown in your owner’s manual. Many cars use reinforced pinch welds or marked pads, and a rubber puck on the saddle helps protect them.
Rather keep the jack in the corner and let someone else do the lifting? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a visit on our contact page.
Short on daytime hours? Bring the car by after we close and leave it with the after-hours drop-off at our Creston shop, 456 Carrier St NE.
