456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Stock, Leveled or Lifted: The Best Control Arms for Ram 1500 Trucks

best control arms for ram 1500: muddy SUV on a rocky trail

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A worn control arm on a half-ton Ram usually announces itself as a dull knock when you back out of the driveway, or a steering wheel that never quite sits centered. Choosing the best control arms for Ram 1500 trucks comes down to three things: which generation you drive, which corner is worn, and whether the truck still sits at factory height.

The listings below are grouped by those three questions. If you are still working out where the noise comes from, our walk-through of clunking noises over bumps is a good place to narrow it down first.

Quick answer

Which control arms fit a Ram 1500?

For a 2009-2018 Ram 1500 or a 2019-2024 Classic at stock height, the MOOG RK643074 is a factory-style upper and the Metrix kit pairs both 4WD lowers. The 2019 and later truck can use the Detroit Axle lower pair. Leveled trucks suit the KSP 0-2 inch uppers. Confirm year and drivetrain on Amazon.

Our Quick Picks

Three listings that cover the most common Ram 1500 jobs. Confirm year, drivetrain and ride height on Amazon before ordering.

MOOG RK643074 product photo
Stock upper

MOOG RK643074

Front left upper, stamped steel

A factory-style MOOG upper arm with the ball joint already in place.

SuitsStock-height 2009-2018 trucks and the Classic
View on Amazon →
Detroit Axle DT Lower Pair product photo
2019+ lower pair

Detroit Axle DT Lower Pair

Front lower, two arms

Both lower arms for the current-generation Ram 1500.

SuitsOwners of the 2019 and later DT
View on Amazon →
KSP 0-2 Inch Upper Arms product photo
Leveled trucks

KSP 0-2 Inch Upper Arms

Front upper pair, 0-2 inch

Tubular uppers sold for stock or lightly leveled Ram 1500s.

SuitsTrucks with a small leveling kit
View on Amazon →

Three Ram 1500 Generations, Three Sets of Arms

Every Ram 1500 built since the 2002 redesign uses independent front suspension with an upper and a lower control arm at each front wheel. The arms changed with each generation, though, and they do not swap between them. The 2002-2008 trucks carry one design, and the 2009-2018 trucks brought new arms that Ram kept on the Ram 1500 Classic, sold alongside the newer model from 2019.

The redesigned 2019 and later Ram 1500, often called the DT, shares very little with the Classic underneath. Listings that say “2019-2024 Ram 1500 Classic” do not fit a 2019 DT, even though the model year matches. A VIN search settles any doubt.

Upper or Lower, Factory Height or Leveled

The lower arm carries the weight of the truck through the spring or air spring, so its ball joint and rear bushing tend to go first. The upper arm sees less load, but on a Ram 1500 its ball joint is part of the arm, so a loose upper joint usually means buying the whole arm.

  • Position and side: many listings are a single arm for one corner, such as front left upper, so check the side named in the title.
  • Drivetrain and suspension: 4WD lower arms differ from most RWD ones, and trucks with the front air suspension option have their own fit notes.
  • Ride height: a leveling kit or lift changes the angle of the upper ball joint, which is why aftermarket uppers are sold by lift range.
  • Serviceability: a grease fitting lets you push fresh grease through the joint, which helps on salted roads.

MOOG’s control arm overview explains the case for a greasable socket, describing how new lubricant flushes out contaminants, and it also covers coatings meant to resist rain, snow, salt and road grime. For a wider look at who makes what, see our guide to the best control arm brands.

Best Control Arms for Ram 1500: Picks by Generation and Lift

Every listing here names specific Ram 1500 years, and most name a position and side. Use Amazon’s fit checker with your exact truck and read the notes under the fit result before ordering.

1. MOOG RK643074: Front Left Upper Control Arm and Ball Joint for 2009-2018 Ram 1500 and Classic

MOOG RK643074 product photo
Key features
  • Front left (driver side) upper position
  • Listed for 2009-2018 Ram 1500 and 2019-2024 Classic
  • Stamped steel arm per listing
  • Ball joint and bushings pre-installed

The MOOG RK643074 is a complete front left upper control arm with its ball joint and bushings already installed. The listing names the 2009-2010 Dodge Ram 1500, the 2011-2018 Ram 1500 and the 2019-2024 Ram 1500 Classic, and for each one it describes the position as front left upper with a stamped steel arm. That matches the factory design on these trucks, so it bolts in where the original arm came out.

On this generation the upper ball joint is part of the arm, and a loose upper joint is one of the more common reasons to replace an upper arm. Buying the whole assembly also renews the two inner bushings, which tend to crack on trucks that have seen many Michigan winters. MOOG’s matching passenger side arm is sold separately as the RK643073, so plan on two listings if both sides are worn.

This arm is meant for a truck at factory height or close to it. It does not fit the 2019 and later DT Ram 1500, and it is not built to correct the angles on a lifted truck. Enter your exact truck in Amazon’s fit checker, note any suspension qualifiers, and book an alignment after installation.

View MOOG RK643074 on Amazon

2. Metrix Premium Front Lower Control Arm Kit: Left and Right Pair for 2006-2018 Ram 1500 4WD and Classic

Metrix Lower Control Arm Kit product photo
Key features
  • Front lower pair, left and right
  • Includes RK641504 and RK621602 assemblies
  • Pre-greased, cast iron per listing
  • 3 year / 36,000 mile limited warranty per listing

This Metrix kit contains two front lower control arms with ball joints, one for each side, sold as replacements for the RK641504 left and RK621602 right part numbers. The listing names the 2006-2008 Dodge Ram 1500 4WD with five-stud wheels, the 2009-2010 Dodge Ram 1500 4WD, the 2011-2018 Ram 1500 4WD, 2013-2018 rear-wheel-drive trucks with front air springs, and the 2019-2024 Ram 1500 Classic 4WD.

Lower arms carry the weight of the front of the truck, so on a high-mileage 4WD Ram they are often the source of a clunk from the rear bushing or a loose lower joint. Metrix describes the arms as cast iron and pre-greased, says its parts are made under IATF 16949 and ISO 9001 certification, and gives a 3 year or 36,000 mile limited warranty from installation. A pair keeps both sides even on a truck that has covered the same miles on each.

The kit leaves out most rear-wheel-drive trucks with coil springs and does not fit the 2019 and later DT. A coil-spring 2WD truck needs a lower arm listed for that setup instead, so check your drivetrain, wheel stud count and suspension type on Amazon before you order.

View Metrix Lower Control Arm Kit on Amazon

pickup stuck on rocks while a man works underneath

3. MOOG RK621606: Front Left Lower Control Arm and Ball Joint for 2006-2012 Ram 1500

MOOG RK621606 product photo
Key features
  • Front left (driver side) lower position
  • Listed for 2006-2010 Dodge Ram 1500
  • Also listed for 2011-2012 Ram 1500
  • Single arm with ball joint assembly

The MOOG RK621606 is a front left lower control arm with the ball joint installed. Its listing names the 2006-2010 Dodge Ram 1500 and the 2011-2012 Ram 1500, which spans the last years of the earlier body style and the first years of the 2009 redesign. That makes it one of the few single lower arms on Amazon aimed at these older trucks.

MOOG’s description is general, saying the arm is built to help maintain wheel alignment, handle road stress and restore steering response once the worn part is removed. The listing does not state a drivetrain, and lower arms for 4WD and 2WD Rams in these years are not always the same. That gap matters, so read the fit checker result and its notes carefully rather than relying on the year alone.

A single arm suits a truck where one lower corner took a hard hit from a pothole or curb while the other side still checks tight. If both lowers are worn, you will need the matching right side part as well. Have the truck aligned after installation, and check the tie rod ends while the front end is apart.

View MOOG RK621606 on Amazon

4. Detroit Axle Front Lower Control Arms: Pair with Ball Joints for 2019-2025 Ram 1500

Detroit Axle DT Lower Pair product photo
Key features
  • Two front lower arms with ball joints
  • Listed for 2019-2025 Ram 1500 (DT)
  • Also listed for Jeep Wagoneer and Grand Wagoneer
  • 10-year warranty per listing

Detroit Axle’s kit includes two front lower control arms with ball joints for the current Ram 1500, the DT. The listing names 2019-2020 Ram 1500 4WD trucks, 2021 and 2022-2024 trucks with the 3.0L, 3.6L or 5.7L engine in a long list of trims from Tradesman to Limited Longhorn, and the 2025 Ram 1500. The same arms are also listed for the Jeep Wagoneer and Grand Wagoneer.

That trim and engine detail is worth reading line by line. Trucks such as the TRX use a different front end, and the listing does not name them. Detroit Axle cites impact, wear and fatigue testing, and this Ram listing comes with a 10-year warranty. It does not say whether the ball joints take grease, so check the photos or the questions on the page if that matters to you.

This kit is the right shape of purchase for a DT owner with worn lower bushings or loose lower joints on both sides. It will not fit a 2019-2024 Ram 1500 Classic. Put your year, engine and trim into the fit checker, then plan an alignment afterward.

View Detroit Axle DT Lower Pair on Amazon

driver's silhouette in a truck at sunset

5. KSP 0-2 Inch Upper Control Arms: Adjustable Tubular Pair for Leveled Ram 1500

KSP 0-2 Inch Upper Arms product photo
Key features
  • Front upper pair for 0-2 inch lift
  • 1.25 inch DOM tubing per listing
  • PU bushings and powder coat finish
  • Replaces RK643074 and RK643073 per listing

KSP sells this pair of tubular upper control arms for a Ram 1500 at stock height or with up to 2 inches of front lift, which covers most leveling kits. The listing says they replace factory part numbers 55398403AA and 55398404AA, along with the MOOG RK643074 and RK643073 and Dorman 522-467 and 522-468. Its fitment line lists 2009-2010 Dodge Ram 1500 and 2011 and later Ram 1500 trucks plus the Classic, in 2WD and 4WD.

Read that fitment line with care. The MOOG arms it replaces are listed for 2009-2018 trucks and the Classic, not the 2019 and later DT, so a DT owner should confirm fit on the fit checker before trusting the year range. KSP builds the arms from 1.25 inch DOM tubing with MIG welds, PU bushings and a powder coat finish.

Polyurethane bushings feel firmer than rubber and can pass more road noise into the cab. These arms suit an owner who leveled the truck and now struggles to get caster or camber in range on the stock uppers. They are not meant for lifts taller than 2 inches. KSP lists a 30-day refund and 1-year replacement parts policy, and an alignment is needed after fitting.

View KSP 0-2 Inch Upper Arms on Amazon

6. Rough Country Forged Aluminum Upper Control Arms: Pair for 2019-2027 Ram 1500 with 3-3.5 Inch Lift

Rough Country Forged Uppers product photo
Key features
  • Forged aluminum upper arm pair
  • Listed for 2019-2027 Ram 1500 with 3-3.5 inch lift
  • Greasable POM ball joints per listing
  • Clevite OE-style rubber bushings

Rough Country sells this pair of forged aluminum upper control arms for the 2019-2027 Ram 1500 running a 3 to 3.5 inch lift. Once a truck sits that high, the factory upper ball joint runs near the end of its travel and the alignment can run out of adjustment. The listing says these arms have their angles corrected for lifted use.

The arms are forged rather than welded, so there are no weld seams in the body. Rough Country fits Clevite OE-style rubber bushings, which keeps the ride closer to stock than polyurethane would, and uses fully greasable ball joints with a polyoxymethylene (POM) ball. The company says the larger ball diameter gives more range of motion than a standard joint, which helps when the suspension droops on rough two-tracks.

These arms are for a lifted DT only. They do not fit the Ram 1500 Classic or a truck at stock height, and they are not a plain replacement part. The listing mentions a limited lifetime replacement warranty. Confirm the lift height and model year on the fit checker, grease the joints on a schedule, and have the alignment set by a shop that knows lifted trucks.

View Rough Country Forged Uppers on Amazon

Quick Fit Table for Ram 1500 Control Arms

The table repeats the fitment each listing gives. Your Ram’s trim and suspension package can still change which arm fits.

Ram 1500 yearsRide heightPositionListing to check
2006-2012StockFront left lowerMOOG RK621606
2006-2018 4WD, 2019-2024 Classic 4WDStockFront lower pairMetrix RK641504 and RK621602 kit
2009-2018, 2019-2024 ClassicStockFront left upperMOOG RK643074
2009-2018, 2019-2024 ClassicLeveled 0-2 inchFront upper pairKSP 0-2 inch uppers
2019 and later DTStockFront lower pairDetroit Axle lower kit
2019 and later DTLifted 3-3.5 inchFront upper pairRough Country forged uppers
Ram 1500 generations and ride heights matched to the control arm listings reviewed above

None of these fit a Ram 2500 or 3500, which use a different front end.

tent and pickup on a beach

Brine, Frost Heaves and Rubber Bushings

West Michigan winters are rough on the front end of a pickup. Brine creeps into split ball joint boots, and the rubber bushings that locate each arm crack and soften after years of salt and cold. Freeze-thaw potholes then hammer the weakened parts every spring.

Checking boots and bushings at each oil change catches most of this early, and a few pumps of grease each fall push out trapped water.

pile of differential gears

Control arm wear rarely happens alone. Tired shocks let the truck bounce harder into every hole, so check them while the front end is apart; our guide to shocks and struts for daily drivers explains what to look for. The warning signs of a failing arm, such as clunks, wandering and uneven tire wear, are much the same on any vehicle, and our article on control arm failure symptoms lists them in detail.

DIY Swap or Shop Job?

Replacing a complete arm is simpler than pressing a ball joint, but it is still safety work. You need the truck secure on jack stands, a way to control the spring or air spring, and a torque wrench for the factory specifications. Final-tighten the bushing bolts with the truck at ride height so the rubber is not twisted.

mechanic working at a cluttered bench

Whichever of the best control arms for Ram 1500 trucks you choose, book an alignment as soon as they are on, because new arms shift caster and camber. If seized bolts or a rusted knuckle make the job more than a weekend project, our suspension repair service in Grand Rapids can inspect the front end and replace the worn parts. Hendrick Hoffman, our owner and head mechanic, holds ASE and State of Michigan certification covering steering and suspension.

Frequently Asked Questions

Do Ram 1500 Classic control arms fit a 2019 or newer Ram 1500?

No. The Classic is the 2009-2018 design kept in production, while the 2019 and later DT is a different truck with different arms. Buy by the exact model name and check the VIN if you are unsure.

Do I need new upper control arms after leveling my Ram 1500?

Not always. A small leveling kit may still align to spec on stock arms. If the shop cannot reach the caster or camber range, or the upper ball joint is binding, aftermarket uppers sold for that lift height are the usual fix.

Should I replace Ram 1500 control arms in pairs?

It is a good idea when both sides have the same mileage and wear. Pairs keep the bushings and joints even from side to side, but a single arm is fine when one side was damaged and the other checks tight.

Is an alignment needed after replacing control arms?

Yes. New arms and bushings change the front geometry slightly, and an alignment keeps the Ram tracking straight and saves the tires.

Front end knocking every time you pull into a parking lot? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or request a suspension check through our contact page.

Can’t get away from the job site during the day? Our after-hours drop-off lets you park the Ram at 456 Carrier St NE and leave the keys for the morning.