456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Stock, Lifted or Heavy Duty: The Best Shocks for OBS Ford Trucks and Broncos

best shocks for obs ford: old dump truck by a colonnade

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A 1990s Ford truck that floats over dips, porpoises on the highway or slams on every expansion joint is usually telling you its shocks are spent. The best shocks for OBS Ford trucks are the ones built for your exact combination of model, drive type and ride height, since a stock F-150 4×4, a lifted Bronco and an F-350 dually all take different lengths.

This guide covers 1987-1996 F-150s and Broncos and 1987-1997 F-250 HD and F-350 trucks. Not sure the shocks are the problem? See our checklist on how to tell if struts or shocks are bad.

Quick answer

What shocks should I put on an OBS Ford?

For a stock-height F-150 4×4, the Rancho RS5000X set or a Bilstein 4600 pair keeps the factory ride with better control. F-250 and F-350 owners can look at the Monroe Gas-Magnum 34732. Lifted trucks need shocks sized to the lift, such as the Bilstein 5100 for 4 inches or Rough Country N3 for 3 to 4.5 inches.

Our Quick Picks

Three listings for stock half-tons, heavy-duty trucks and lifted rigs. Confirm your year, drive and lift on Amazon.

Rancho RS5000X Set product photo
Stock F-150 4×4

Rancho RS5000X Set

Shock set, 0 inch lift

A matched Rancho set for an unlifted four-wheel drive half-ton.

Suits1987-1996 F-150 4WD owners refreshing every corner
View on Amazon →
Monroe Gas-Magnum 34732 product photo
F-250 and F-350

Monroe Gas-Magnum 34732

Single shock, heavy duty

A Monroe truck shock for the three-quarter and one-ton OBS trucks.

SuitsF-250 and F-350 owners who work their trucks
View on Amazon →
Bilstein 5100 24-186513 product photo
4 inch lift

Bilstein 5100 24-186513

Front, 46mm monotube

A Bilstein front shock sized for a lifted Bronco or F-150 4×4.

SuitsLifted OBS trucks that see trails and highway
View on Amazon →

Pin Down the Truck Before the Part Number

Ford built these trucks with several front ends, each with its own shock length. Two-wheel drive F-150 and F-250 pickups use Twin I-Beam front suspension with coil springs. Four-wheel drive F-150s and Broncos use the Twin Traction Beam, often shortened to TTB, while F-350 4x4s ride on a solid front axle.

On every one of them the shock is a separate part from the spring. That matters for the job: unlike a strut car, you do not need to take a spring apart to change a shock, so the coil spring compressor stays in the drawer unless you are also replacing the springs.

  • Model year: OBS half-ton parts stop at 1996, while the F-250 HD and F-350 run through 1997.
  • Drive type: 2WD and 4WD trucks take different shocks.
  • Ride height: a lift or leveling kit changes the length you need.
  • Position: front and rear shocks are different parts.

Twin-Tube, Monotube and Lift Height

Most budget and OE-style shocks are twin-tube designs, with an inner pressure tube and an outer reserve tube. Monotube shocks, such as the Bilstein models below, use one larger tube with the gas and oil kept apart, which Bilstein says gives fade-free damping.

A twin-tube suits a commuter truck that rarely leaves pavement, while a monotube suits trucks that tow, haul or run two-tracks. The Gabriel shock FAQ also notes that a light oil mist on the body is normal, but oil running down the side means the shock is leaking and due for replacement.

On a lifted truck, measure between the shock mounts at ride height and compare it with the listing’s extended and collapsed length. A shock that is too short tops out, and one that is too long bottoms inside its body.

Best Shocks for OBS Ford: Six Listings Matched to the Truck

Each listing names its own years, drive type and position or lift. Use that as a shortlist, then check your truck in Amazon’s fit tool, since no single part number covers every OBS version.

1. Rancho RS5000X Gas Shocks Set: Stock-Height Shocks for 1980-1996 F-150 4WD

Rancho RS5000X Set product photo
Key features
  • Listed for 1980-1996 F-150 4WD with 0 inch lift
  • Also names 1980-1996 F-250 RWD and 1997 F-250 HD RWD
  • 16mm nitro-carburized rod and 35mm piston
  • Twin-tube body with all-weather fluid

The Rancho RS5000X set is sold as a matched group of gas shocks for one truck, so you skip matching front and rear part numbers. Its Amazon listing names the 1980-1996 F-150 4WD at stock height, along with the 1980-1996 F-250 RWD and the 1997 F-250 HD RWD. The listing also warns that an RS8125 axle shim kit may be needed on the rear axle for shock-to-axle clearance, so read that note before you start.

Rancho describes the RS5000X as a twin-tube shock with Cross Tuned valving, which pairs its rebound valving with a separate compression stage. The maker says the progressive engagement valving is tuned for each vehicle to soften the first hit of a low-speed bump. Each shock has a 16mm nitro-carburized rod, a 35mm sintered iron piston, double-welded loops and a polyvinyl boot that helps keep grit off the rod.

This set suits an OBS half-ton that still sits at factory height and mixes commuting, light hauling and dirt roads. It is not sized for a lifted truck, and the rear shim note means a few owners will need extra parts. Check what the listing photos show in the box, then confirm your exact year and drive in Amazon’s fit checker.

View Rancho RS5000X Set on Amazon

2. Bilstein 4600 24-016186: Rear Monotube Shock Pair for 1980-1996 F-150 4WD

Bilstein 4600 Rear Pair product photo
Key features
  • Rear pair, part number 24-016186
  • Listed for 1980-1996 F-150 4WD
  • Monotube gas shock design
  • Washers, bushings and nuts included

This listing is a rear pair of Bilstein 4600 monotube gas shocks, part number 24-016186, and its title names the 1980-1996 F-150 4WD. Buying the pair in one listing covers both sides of the rear axle, which is how shocks should be replaced. The listing says all the washers, bushings and nuts needed come in the box, while the factory shock mounting bolts are reused.

Bilstein positions the 4600 series as a direct replacement for original shocks on stock-height trucks and SUVs. The monotube layout keeps gas and oil apart, and Bilstein says this gives consistent damping without fade as the shock heats up on washboard roads or a long tow. Compared with a basic twin-tube, a monotube tends to feel firmer, which many truck owners like when the bed is loaded.

Because this is a rear-only listing, you will need a separate front pair for the TTB axle, and the Gabriel or Rancho picks on this page are options there. Reused factory bolts on a Michigan truck are often rusted, so plan on new bolts if yours are pitted. The listing does not cover 2WD trucks or lifted rear ends, so confirm your truck in Amazon’s fit checker before you order.

View Bilstein 4600 Rear Pair on Amazon

red dirt road through a forest

3. Monroe Gas-Magnum 34732: Heavy-Duty Truck Shock for 1987-1996 F-250 and 1985-1997 F-350

Monroe Gas-Magnum 34732 product photo
Key features
  • Listed for 1987-1996 F-250 and 1997 F-250 HD
  • Also names 1985-1997 F-350
  • Larger bore and 2 inch reserve tube
  • Nitrogen gas charge and all-weather fluid

The Monroe Gas-Magnum 34732 is a single heavy-duty shock built for full-size trucks and vans. Its Amazon listing names the 1987-1996 Ford F-250, the 1997 F-250 HD and the 1985-1997 F-350, which makes it one of the few listings here aimed at the three-quarter and one-ton OBS trucks. The title does not say front or rear, so the position for your truck comes from the fit checker notes.

Monroe says the Gas-Magnum line uses full-displaced valving on the compression stroke to keep ride and handling controlled under weight. The listing points to a heavy-duty nitrocarburized rod on non-shield units, a sintered iron piston and a self-lubricating seal. A larger bore and a 2 inch reserve tube hold more oil, which Monroe says helps the shock run cooler and last longer on a truck that hauls.

This shock suits an F-250 or F-350 that pulls a trailer, carries a camper or does farm work and needs a durable stock-height replacement. It is sold one at a time, so order two for an axle. It is not for a lifted truck or a half-ton, and some F-250 and F-350 versions take a different part. Enter your year, drive and cab in Amazon’s fit tool first.

View Monroe Gas-Magnum 34732 on Amazon

4. Gabriel Ultra Truck G63410: Front Shock for 1980-1996 Bronco and F-150 4WD

Gabriel Ultra G63410 product photo
Key features
  • Front position, sold as one shock
  • Listed for 80-96 Bronco and 80-96 F-150 4WD
  • 6.78 in stroke, 18.55 in extended length
  • Twin-tube, bolt-on replacement

The Gabriel Ultra Truck G63410 is a front shock listed for the 1980-1996 Ford Bronco and 1980-1996 F-150 4WD, plus some early F-250 and F-350 4WD trucks. That covers the common stock-height TTB front end found on most OBS half-ton 4x4s and full-size Broncos. It is sold as a single shock, so you need two for the front axle.

Gabriel publishes the dimensions on the listing, which helps when you want to check against your own truck. It gives a 6.78 inch stroke, an extended length of 18.55 inches and a collapsed length of 11.77 inches, with an S12 upper mount and EB1 lower mount. The listing also gives a long interchange list, including Monroe and Rancho numbers, which is handy for matching an old part.

Gabriel describes the Ultra as a premium OE replacement with a twin-tube design and bolt-on installation for normal driving. That makes it a sensible pick for a stock truck that mostly sees pavement, where a firm monotube might feel harsh. It is not a lift shock and is not aimed at heavy towing. Measure your mounts if the truck has a leveling kit, and confirm fit in Amazon’s checker.

View Gabriel Ultra G63410 on Amazon

wrecked car body with a wheel

5. Bilstein 5100 24-186513: Front Monotube Shock for 1980-1996 Bronco and F-150 4WD with 4 Inch Lift

Bilstein 5100 24-186513 product photo
Key features
  • Front shock for a 4 inch lift
  • Listed for 1980-1996 Bronco and F-150 4WD
  • 46mm monotube with digressive valving
  • Direct fit with hardware included

The Bilstein 5100 24-186513 is a front shock sized for a lifted truck. Its Amazon listing names the 1980-1996 Ford Bronco and the 1980-1996 F-150 4WD with a 4 inch lift, using the auxiliary shock position mounted forward of the coil spring. That is a common setup on OBS trucks running a mild suspension lift and larger tires.

Bilstein builds the 5100 around a 46mm monotube body and its patented digressive valving, which the maker says reacts quickly to changing surfaces. The monotube design keeps damping steady as the shock heats up, and the listing calls it a direct-fit install with hardware included. Bilstein’s broader 5100 range is offered in many lengths for different lift heights, so the number on the box matters.

This is the right type of shock for a Bronco or 4×4 half-ton that has been lifted around 4 inches and splits its time between highway miles and dirt roads. It will be too long for a stock truck and too short for a big lift, and it is sold as one front shock. Order a pair, match the rears to your rear lift height, and confirm the fit in Amazon’s checker.

View Bilstein 5100 24-186513 on Amazon

6. Rough Country N3 23237: Front Shocks for 1980-1996 F-150 4WD with 3-4.5 Inch Lift

Rough Country N3 23237 product photo
Key features
  • Front shocks for a 3 to 4.5 inch lift
  • Listed for 1980-1996 F-150 4WD
  • 54mm body with 10-stage valving
  • Nitrogen charged, rubber bushings

The Rough Country N3 23237 is a front shock listing for the 1980-1996 Ford F-150 4WD with a 3 to 4.5 inch lift. Rough Country builds lift kits for these trucks, so this shock suits owners who already run one of its kits or a similar mid-height lift and need new front damping. Because the lift range is wide, measure your mounts before you buy.

According to the listing, the N3 uses a 54mm body for faster cooling and a 10-stage variable valving setup. It is nitrogen charged and uses rubber bushings, with a spring-loaded piston rod seal and military-spec fluid rated for very cold temperatures. The listing quotes a tensile strength of 36kN and says Rough Country backs the shock with a limited lifetime replacement warranty.

These shocks make sense on a lifted F-150 4×4 that sees snowy roads, fields and trails, where a stock-length shock would top out. They will not fit a stock-height truck, and they are not listed for the Bronco or the heavier F-250 and F-350. Pair them with rears that match your rear lift, and check the exact year and lift height in Amazon’s fit checker before you order.

View Rough Country N3 23237 on Amazon

Which Shock Goes on Which Truck

The chart sorts the best shocks for OBS Ford models by what each listing states. It is a shortlist to check against the fit tool, not a promise that a part fits your truck.

Truck and heightFrontRear
F-150 4WD, stock (1987-1996)Gabriel Ultra G63410, or the Rancho RS5000X setBilstein 4600 24-016186 pair, or the Rancho set
Bronco, stock (1987-1996)Gabriel Ultra G63410Check the fit tool for the rear
F-250 and F-350 (1987-1997)Monroe Gas-Magnum 34732, position per fit notesMonroe Gas-Magnum 34732, position per fit notes
F-150 4WD or Bronco, 4 inch liftBilstein 5100 24-186513Match to rear lift height
F-150 4WD, 3 to 4.5 inch liftRough Country N3 23237Match to rear lift height
OBS Ford trucks and Broncos matched to the shock listings reviewed above

Replace shocks in axle pairs so the truck damps the same on each side. On a high-mileage truck, a full set of four keeps the front and rear feeling matched.

black and white photo of an old pickup

Rust, Potholes and Old Rubber

West Michigan winters are rough on a thirty-year-old truck. Road salt seizes the lower shock bolts, and spring potholes beat on worn shocks. Soak the hardware with penetrating oil a day ahead, and expect to cut a bolt or two.

Before you buy, run the bounce test from the AA1Car shock and strut diagnosis guide: push down hard on each corner and let go. If the truck rebounds more than once or twice, that shock is worn. The same guide notes that a ride height difference of more than half an inch side to side points to weak springs, which new shocks will not fix.

grinder throwing sparks

A squeak over speed bumps is often a dry bushing or sway bar link, as our page on squeaks when driving over bumps explains. A hard clunk can be a worn ball joint, so see our guide to ball joints for pickups before you blame the shocks.

Doing It at Home or Bringing It In

Shocks on these trucks are a bolt-on job with jack stands and a breaker bar. Support the axle so it does not drop and stretch the brake hoses. If you are comparing OBS parts with newer vehicles in the driveway, our roundup of shocks and struts for daily drivers covers cars and crossovers.

dirt road through a quiet village

A shock swap alone rarely changes alignment, but TTB camber shifts with ride height, so align the truck after a lift or new springs. Even the best shocks for OBS Ford trucks cannot hide worn bushings, and our suspension repair service in Grand Rapids can check the whole front end. Steering and suspension is one of the areas where Hendrick Hoffman, our owner and head mechanic, holds both ASE and State of Michigan certification.

Frequently Asked Questions

Does a 1997 F-150 take OBS shocks?

No. The 1997 F-150 is the newer body with a different suspension. The old body style stayed on the 1997 F-250 HD and F-350, so check the exact model before you order.

Should I pick a Bilstein 4600 or 5100 for my truck?

The 4600 is Bilstein’s stock-height replacement line. The 5100 listings are sized for lifted trucks, such as the 24-186513 for a 4 inch lift, so choose by your truck’s ride height.

Do I need a spring compressor to change OBS Ford shocks?

No. These trucks use separate shocks rather than struts, so the spring stays in place. You only need a compressor if you are replacing coil springs too.

Should I replace all four shocks at once?

Always replace them in pairs on the same axle. On a high-mileage truck, doing all four at once gives an even ride front to rear.

Old Ford bucking down the road or wandering after every bump? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or ask for a suspension check on our contact page.

If the truck is working while we are open, bring it to 456 Carrier St NE, Grand Rapids, MI 49505 in the evening and leave it with our after-hours drop-off.