456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

From Civic to Ridgeline: Choosing the Best Floor Jack for Honda

best floor jack for honda: bright in a garage

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

Lots of households park two Hondas side by side, say a Civic for commuting and a CR-V or Pilot for the family. The best floor jack for Honda owners in that spot has to start low enough for the car and climb high enough for the crossover, all without a second jack in the corner.

This guide covers the two height numbers to compare, where Honda lift points usually sit, and five floor jacks grouped by the models they suit.

Want a wider look at low cars of every brand? Our guide to low profile floor jacks for cars goes deeper on frame materials. Setting up a garage for the first time? Our beginner car maintenance tool list shows what to buy alongside the jack.

Quick answer

Which floor jack works on a Honda?

Match the jack’s listed heights to your model. For a Civic or Accord, the YELLOW JACKET 3 ton starts under 4 inches. For a CR-V or Odyssey, the GEARWRENCH GWHDFJ3T is a sturdy steel choice. For a Pilot or Ridgeline, the Daytona 4 ton reaches just over 20 inches.

Our Quick Picks

Three starting points, matched to the Honda you park most: a sedan or small crossover, a CR-V class all-rounder, and a heavier three-row or pickup.

YELLOW JACKET 3 Ton product photo
Civic and Accord

YELLOW JACKET 3 Ton

3 ton, 3-15/16 to 18-5/16 in.

A low entry height for sedans, with enough rating for a CR-V too.

SuitsCivic, Accord, Insight and HR-V owners
View on Amazon →
GEARWRENCH GWHDFJ3T product photo
CR-V all-rounder

GEARWRENCH GWHDFJ3T

3 ton, 5.25 to 18.25 in.

A steel shop-style jack listed to the PASE-2019 standard.

SuitsCR-V, Odyssey and mixed Honda driveways
View on Amazon →
Daytona 4 Ton product photo
Pilot and Ridgeline

Daytona 4 Ton

4 ton, 4-1/4 to 20-1/4 in.

Extra height and rating for three-row SUVs, minivans and pickups.

SuitsPilot, Passport, Odyssey and Ridgeline
View on Amazon →

Height Numbers That Matter on a Honda

Capacity rarely limits a home jack on a Honda, because you only lift one end or one corner at a time. The two figures that decide whether a jack works are the minimum saddle height and the maximum lift. Every listing states both, and they are worth more attention than the ton rating printed on the side.

Minimum height has to sit below the lowest part of the car in the jack’s path, which on a Civic or Accord is often the front spoiler rather than the lift point itself. Maximum height has to raise the car far enough to slide a jack stand underneath with the stand set at a sensible working height. On a Ridgeline or a Pilot, that top figure becomes the real test.

  • Measure from the floor to the lowest point ahead of the lift point with the car on level concrete.
  • Compare that number with each jack’s listed minimum, leaving a small margin for a rubber pad.
  • Check the maximum against the height your stands need, plus a little extra to place them.
  • Look at frame length too, since a short jack may not reach a center point under a minivan.

Finding the Lift Points on Your Honda

Honda prints the approved lifting points for each model in the owner’s manual, and the layout differs between generations. Many Honda cars and crossovers use a reinforced front center point on the subframe and a rear center point near the crossmember or tow hook area. The pinch welds along the sills are usually meant for the spare tire jack and for supporting the car on stands.

Lifting at a center point raises a whole end at once, which is handy for an oil change or a brake job on both sides. It also needs a jack with enough reach to get the saddle under the middle of the car. Whatever point you pick, confirm it in the manual for your exact year and model before the first lift.

Best Floor Jack for Honda Garages: Five Jacks Up Close

Specs below come from each Amazon listing, or from the maker’s page where noted. Read them against the measurements you took under your own Honda.

1. YELLOW JACKET 3 Ton Floor Jack: Aluminum and Steel, 3-15/16 to 18-5/16 in. Lift

YELLOW JACKET 3 Ton product photo
Key features
  • 3 ton (6,600 lb) capacity
  • 3-15/16 to 18-5/16 in. lift range
  • Dual piston pump
  • Listed to ANSI/ASME standards

A Civic or Accord with a front air dam leaves little room for a tall jack, and this aluminum and steel unit is built around that problem. Its listing puts the saddle at 3-15/16 inches when fully lowered and 18-5/16 inches at full extension, with a 3 ton rating that covers one end of any Honda car or crossover. The mixed frame keeps weight down compared with an all-steel jack of the same capacity.

Two pump pistons move the saddle up quickly, so you spend fewer strokes getting it to the lift point. A large rubber pad sits on the saddle, a foam sleeve on the handle keeps the bar off the bumper, and a load limiting valve cuts in if the jack is asked to carry more than its rating. Two swivel casters and two front rollers let it steer under the car, while a side grip makes it easier to carry.

This is a sensible pick for a garage with a Civic, an Accord or a small crossover such as the HR-V. The lift range clears a stand under most Honda cars, though a lifted Ridgeline or a Pilot on large tires may want more height. Confirm your lift points in the owner’s manual before the first use.

View YELLOW JACKET 3 Ton on Amazon

2. BIG RED AT815016LR Racing Floor Jack: 1.5 Ton, 3.5 to 14 in. Lift, Dual Piston

BIG RED AT815016LR product photo
Key features
  • 1.5 ton (3,000 lb) capacity
  • 3.5 to 14 in. lift range
  • Aluminum and steel frame
  • Side carry handle and knurled bar

Torin’s BIG RED AT815016LR is a compact racing style jack aimed at small, low cars rather than family haulers. The listing rates it at 1.5 tons and gives a 3.5 to 14 inch range, so it slides under a Civic Si or a Fit and lifts one corner for a wheel or brake job. Aluminum and steel construction keeps it light enough to carry with one hand using the side grip.

A dual piston pump speeds up the first part of the stroke, and the handle is knurled so it does not slip in cold or oily hands. Foam on the handle protects paint when you lower the bar near a bumper. Because the frame is short, it stores easily on a shelf or in a trunk for a trip to a track day or a relative’s driveway.

The limits are the reason it costs less effort to move. Fourteen inches of maximum lift is enough for a tire swap on a small Honda car, but it may leave too little height to slide a stand under a CR-V, an Odyssey or a Pilot. If a compact car is all you lift, and you value a jack you can pick up easily, this one fits that brief well.

View BIG RED AT815016LR on Amazon

winding road through a lush green mountainous landscape under a bright blue clear sky

3. GEARWRENCH GWHDFJ3T Heavy-Duty Floor Jack: 3 Ton, Dual Piston, ASME PASE-2019

GEARWRENCH GWHDFJ3T product photo
Key features
  • 3 ton capacity, forged steel
  • 5.25 to 18.25 in. lift (maker spec)
  • Meets ASME PASE-2019
  • Tool tray and protected handle

GEARWRENCH built the GWHDFJ3T as a steel service jack for people who want a shop feel at home. The GEARWRENCH product page for the GWHDFJ3T lists a lowest position of 5.25 inches, a highest position of 18.25 inches and a catalog weight of 67.5 pounds. It also states compliance with ASME PASE-2019, the safety standard for portable garage lifting gear.

The dual piston pump gives a steady, quick rise, and the rubber saddle grips the lift point instead of skating on it. A protected handle design keeps the bar from marking the car, and a small tray on the frame holds lug nuts or sockets while you work. Iron casters and a welded steel body give it a planted, solid stance on a concrete floor.

That 5.25 inch starting height clears a CR-V, Odyssey, Passport or Pilot without trouble, and many Accords too, but a lowered Civic or one with a deep front lip may be too tight. The weight also means it stays in the garage rather than riding in a trunk. For a household with one car and one crossover, it is a balanced, sturdy choice.

View GEARWRENCH GWHDFJ3T on Amazon

4. Daytona 4 Ton Steel Floor Jack: 4-1/4 to 20-1/4 in. Lift with Rapid Pump

Daytona 4 Ton product photo
Key features
  • 4 ton capacity
  • 4-1/4 to 20-1/4 in. lift range
  • Dual piston Rapid Pump
  • Removable, rotating saddle

Daytona’s 4 ton steel jack covers the widest spread of Honda models in this list. Its listing gives a lift range from 4-1/4 to 20-1/4 inches, so the same saddle can start under an Accord and still reach high enough to set a tall stand under a Ridgeline. The 4 ton rating leaves comfortable headroom when you lift the front of a loaded Pilot or Odyssey.

The Rapid Pump system uses two pistons to bring the saddle up to the vehicle quickly, then slows to a controlled lift once it takes the load. Ball bearing rear casters swivel through a full circle, which matters when you have to angle the jack toward a center lift point under a minivan. The saddle rotates and lifts out, so it can be swapped for a lift accessory when a job calls for one.

Expect real weight from an all-steel 4 ton frame, which makes it a garage jack rather than one to carry. It can feel like more jack than a single Civic owner needs, but for a home with a Pilot or a pickup in the driveway, the extra height is useful. Check that your stands reach the same height range.

View Daytona 4 Ton on Amazon

interior of a traditional Swiss sawmill with wooden beams and vintage tools

5. Big RED AT83006UR Long Neck Floor Jack: 3 Ton with Extra Saddle for SUVs

Big RED AT83006UR product photo
Key features
  • 3 ton (6,000 lb) capacity
  • Extra-long neck for taller vehicles
  • Extra saddle included
  • 360-degree swivel casters

The Big RED AT83006UR takes a different route to lifting a tall Honda: a long neck that puts the saddle out ahead of the wheels and higher off the floor. Torin’s listing describes it for SUVs and extended height trucks and includes an extra saddle in the box. For the 3 ton model, the listing gives a minimum height of 5-7/8 inches and a maximum of 17-1/4 inches.

That long neck shortens the pumping needed before the saddle meets a raised lift point, which saves effort on a Ridgeline or a Pilot with larger tires. Swivel casters let it turn in tight garage bays, and the trolley frame rolls easily on smooth concrete. The listing also states a second range for a smaller version, so read the product details carefully before you order.

Its 17-1/4 inch peak is lower than the Daytona’s, so this jack makes the most sense when reach and an easy start matter more than raw height. It is a poor match for a low Civic, where the higher starting point can block the jack from sliding in. Think of it as a second jack for the family SUV rather than a single all-purpose tool.

View Big RED AT83006UR on Amazon

Matching a Jack to Your Honda Model

Use the table as a quick sort by model group. Lift figures are the listed or maker figures for each jack.

Honda groupWhat limits the jackGood matchListed lift range
Civic, Fit, InsightLow front spoilerBIG RED AT815016LR or YELLOW JACKET 3 ton3.5 to 14 in. / 3-15/16 to 18-5/16 in.
Accord, HR-VEntry height and reachYELLOW JACKET 3 ton3-15/16 to 18-5/16 in.
CR-V, OdysseyCenter point reachGEARWRENCH GWHDFJ3T5.25 to 18.25 in.
Pilot, PassportMaximum heightDaytona 4 ton4-1/4 to 20-1/4 in.
RidgelineHeight and ground clearanceDaytona 4 ton or Big RED AT83006UR4-1/4 to 20-1/4 in. / 5-7/8 to 17-1/4 in.
Best floor jack for Honda models grouped by what limits the lift, with each jack’s listed range.

When two jacks both fit, the best floor jack for Honda households is the one that covers every model in the driveway. A single jack with a low start and a tall top saves garage space and avoids a second purchase later when the family adds a crossover.

stunning mountain valley landscape with a winding road under a clear blue sky

Salt, Rust and Safe Lifting in West Michigan

A floor jack only raises the car. Once a Honda is up, lower it onto a pair of rated jack stands placed at the support points in the manual, and only then reach or slide underneath. Hydraulic seals can bleed down without warning, so a car resting on a jack alone is never a safe place to work.

  • Set the parking brake and chock the wheels that stay on the ground.
  • Work on flat, dry concrete, never on soft asphalt or an icy apron.
  • Open the release valve slowly when you lower the car back down.
  • Torque the lug nuts to the owner’s manual figure once the wheel is on the ground.
rustic indoor workshop with wooden tables

Grand Rapids winters are hard on older Hondas. Road salt works into the sill seams and subframe mounts, so look closely at the metal before you place the saddle and skip any spot that flakes or flexes. For the lug nuts afterward, see our torque wrench guide for wheel lug nuts.

Jobs Better Left to a Lift

A good floor jack handles tire rotations, pad swaps and oil changes on nearly any Honda. Longer jobs that need the whole car high and level, or a corroded lift point that no longer looks solid, are better handled on a two-post lift. If brakes are the reason you are lifting, our brake pad guide for Honda models helps you pick the right set first.

idyllic rural road leading to distant mountains under dramatic clouds

When your Honda’s maintenance minder calls for its next service, our factory scheduled maintenance in Grand Rapids covers the manual’s checklist with the car on a lift. A noise from a worn caliper or rotor that you spot while jacking is a job for our brake repair service.

Frequently Asked Questions

What size floor jack do I need for a Honda CR-V?

A 3 ton jack is plenty, since you lift one end at a time. What matters more is a maximum height around 18 inches or more so a stand fits underneath, plus a minimum height low enough to clear the front of the car.

Is a 1.5 ton jack enough for a Honda Civic?

For lifting one corner of a Civic, usually yes. The catch is height: a compact jack that tops out near 14 inches may not raise the car far enough to set a stand at a comfortable working height.

Can I use the pinch welds to lift my Honda with a floor jack?

Honda usually intends the pinch welds for the spare tire jack and for jack stands, with separate front and rear center points for a floor jack. Check the lifting page in your owner’s manual, because the points vary by model and year.

Which floor jack lifts a Honda Pilot or Ridgeline high enough?

Look for a maximum lift of about 20 inches. Of the jacks in this guide, the Daytona 4 ton lists the tallest range at 4-1/4 to 20-1/4 inches, which also lets it start under most Honda cars.

Prefer to keep your weekend free and let someone else get the Honda in the air? Ring 456 AutoFix at 616-279-3832 between 8am and 5pm, Monday to Friday, or request an appointment on our contact page.

Working hours that clash with ours? Our after-hours drop-off means you can bring the car to 456 Carrier St NE in Creston once we have closed for the day.