As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
An SUV carries more weight higher off the road than a sedan, so worn dampers show up fast: the body leans hard in turns, the nose dips at every stop and the rear keeps bobbing after a dip. The best shocks and struts for SUVs are the listings built for your exact model, years and corner, because no single strut fits every crossover or truck-based SUV.
This hub covers six front listings for popular SUVs, from the RAV4 and CR-V to the Explorer and 4Runner. If you drive a sedan or a small hatchback, our guide to shocks and struts for everyday commuter cars is the better fit.
Quick answer
Which struts should an SUV owner buy?
Buy a listing that names your SUV, its years and the corner. For most crossovers, a loaded assembly such as a Monroe Quick-Strut or Gabriel ReadyMount restores factory height with no spring compressor. Bilstein’s B4 suits owners keeping good springs, and the B8 5100 gives a 4Runner firmer front control.
Our Quick Picks
Three quick picks: a loaded Monroe for the 2006 to 2012 RAV4, a Gabriel ReadyMount for the 2016 to 2019 Explorer and a Bilstein 5100 for the 2010 to 2022 4Runner. All six listings are reviewed below.

Monroe Quick-Strut 272276
Renews the damper, spring and mount on an aging RAV4 in one unit.

Gabriel G57819 Ultra ReadyMount
A ready-to-bolt corner sized for a heavy family hauler.

Bilstein B8 5100 24-328258
A firmer front damper for a truck-based SUV.
Crossover or Body-on-Frame: Know What Holds Your SUV Up
Most of today’s SUVs are crossovers built like a tall car. A RAV4, CR-V, Equinox, Explorer or Pilot rides on a MacPherson strut at each front wheel, where the damper and coil spring work together as one load-bearing unit.
Truck-based SUVs such as the 4Runner and FJ Cruiser are different. They carry the front coil spring on a coilover shock between two control arms, so the shock steers nothing and the spring often stays with the vehicle.
- Unibody crossover: front struts carry the weight and affect alignment, so treat them as a steering part too.
- Body-on-frame SUV: front coilover shocks, often with a height adjustment option on aftermarket units.
Loaded, Bare or Height-Adjustable: Pick the Type First
A loaded strut, sold as a Quick-Strut, ReadyMount or complete assembly, arrives with a new spring, upper mount, bumper and boot already fitted. Monroe’s Quick-Strut assembly page describes it as a fully assembled unit that needs no spring compressor.
A bare strut is the damper alone. It costs less to ship and lets you pick a premium damper, but the factory spring and mount have to be moved across. Compressing an SUV spring stores serious energy, so read our guide to coil spring compressors built for strut work before you try it at home.
Best Shocks and Struts for SUVs: Six Listings by Vehicle
Each listing below covers one SUV, one range of years and one front corner. Before you order, enter your year, model, engine, drive type and trim in Amazon’s fit checker, then buy the matching opposite-side part so both struts on the axle are new.
1. Monroe Quick-Strut 272276: Front Left Strut and Coil Spring Assembly for 2006-2012 Toyota RAV4

- Listed for 2006-2012 Toyota RAV4
- Strut, coil spring and upper mount preassembled
- No spring compressor needed
- Salt spray tested protective coating
The Monroe Quick-Strut 272276 is a complete front corner for the third-generation Toyota RAV4, and the listing names 2006 to 2012 models. Parts catalogs place this number on the driver side, with 272275 sold for the passenger side, so plan on ordering both. RAV4s of these years came with four-cylinder and V6 engines, and catalogs do not always agree on which engines this part covers, so enter your engine in the fit checker before buying.
Each unit arrives with the strut, an application-specific coil spring and a premium upper mount already put together. Monroe says the spring is calibrated to the original design to restore ride height, and that the mount helps cut noise, vibration and memory steer. The steel body has a protective coating that Monroe salt spray tests, which helps on a crossover that sees Michigan winters.
The appeal here is how complete the repair is. You unbolt the worn corner and bolt in a new one, with no spring compressor and no transfer of old rubber parts. It suits an owner whose RAV4 has sagged, bounces after dips or clunks over bumps and who wants the factory ride back. It is not meant for lifted builds or a firmer, sportier feel.
View Monroe Quick-Strut 272276 on Amazon
2. Gabriel G57819 Ultra ReadyMount: Front Left Strut and Coil Spring Assembly for 2016-2019 Ford Explorer

- Listed for 2016-2019 Explorer and Police Interceptor Utility
- Pre-assembled strut, spring and mount
- Stroke 8.11 in, extended length 23.15 in
- No spring compressor needed
Gabriel’s G57819 Ultra ReadyMount covers the front left corner of the 2016 to 2019 Ford Explorer, and the listing also names the Police Interceptor Utility of the same years. The right side is sold as its own part, so you need two boxes for one axle. Explorers from this period were built with several engines and drive types, which makes the fit checker worth a careful look before you check out.
The assembly comes fully put together with the strut, coil spring and upper mount, and Gabriel lists the specs plainly: an 8.11 inch stroke, a 23.15 inch extended length and a 15.04 inch collapsed length. The interchange list includes Monroe 172730 and 272730, which helps when you are cross-checking an older receipt or a parts store quote. Gabriel brands it as part of its G-Force ride control line and says each design is fit and ride tested.
This one suits a three-row Explorer that hauls a family and cargo and has started to wallow on highway ramps or dip hard under braking. Because it bolts in without a spring compressor, it is a fair driveway job with a good jack and stands. It is not a lift or leveling part.
View Gabriel G57819 Ultra ReadyMount on Amazon

3. Gabriel G57695 Ultra ReadyMount: Front Left Strut and Coil Spring Assembly for 2010-2015 Honda Pilot

- Listed for 2010-2015 Honda Pilot
- Strut, coil spring and mount pre-assembled
- Stroke 7.56 in, extended length 24.61 in
- Interchanges with Monroe 172648
The Gabriel G57695 Ultra ReadyMount is the driver side front strut assembly for the second-generation Honda Pilot, listed for 2010 to 2015. The passenger side is a separate part number, and the two should go in together so the SUV sits and brakes evenly. Check the fit checker notes for your trim and drive type, since Pilots were sold in both front and all-wheel drive form.
Gabriel ships it fully assembled, with the strut, coil spring and upper mount ready to bolt in. The listing gives a 7.56 inch stroke, a 24.61 inch extended length and a 17.05 inch collapsed length, and it lists interchange numbers including Monroe 172648 and KYB SR4232. Those cross references are handy when you want to compare it with a part you already have on the shelf or a quote from a parts counter.
A Pilot of this age has usually worked its factory struts hard, and the original springs and mounts have aged with them. Swapping in a complete assembly takes care of all three at once and skips the spring compressor step. It suits owners who want a quiet, stock-height ride for commuting and road trips. Anyone after a raised stance or firmer valving should look elsewhere.
View Gabriel G57695 Ultra ReadyMount on Amazon
4. Monroe Quick-Strut 272527: Front Left Strut and Coil Spring Assembly for 2010-2017 Chevrolet Equinox

- Listed for 2010-2017 Chevrolet Equinox
- Preassembled strut, spring and upper mount
- No spring compressor needed
- Coated steel, salt spray tested
Monroe’s Quick-Strut 272527 is a loaded front strut for the 2010 to 2017 Chevrolet Equinox, the long-running second generation. Parts catalogs list it for the front left, and Monroe sells the right side under 272526, so order both for an even repair. Some Equinox trims of these years were built with larger wheels and different suspension parts, which is why the fit checker notes deserve a careful read.
Like other Quick-Strut units, it arrives with the strut, coil spring and upper mount assembled and ready to install. Monroe says the spring is matched to the original design to bring back ride height, and that the premium mount helps keep steering smooth while reducing noise and memory steer. The steel is coated against rust and tested with salt spray, which matters for a crossover parked outside through a Grand Rapids winter.
The Equinox is a common daily driver, and many of these SUVs now carry plenty of miles on their original front struts. A one-piece replacement like this suits an owner who wants a stock ride without taking springs apart. It bolts in with ordinary hand tools plus a jack and stands. It is not aimed at lowering, lifting or a firmer handling setup.
View Monroe Quick-Strut 272527 on Amazon

5. Bilstein B4 22-214089: Front Left Twin-Tube OE Replacement Strut for 2007-2016 Honda CR-V

- Listed for 2007-2016 Honda CR-V
- Twin-tube gas-pressure design
- OE replacement damping
- Bare strut, reuses your spring and mount
The Bilstein B4 22-214089 is a front left strut for the Honda CR-V, and the listing names 2007 to 2016 models. It is a bare strut, meaning you get the damper only, without a new spring or upper mount. The passenger side is sold separately, and you should confirm your model year and trim in the fit checker because the CR-V changed generations during that span.
Bilstein describes the B4 as its OE replacement line, built with twin-tube gas-pressure technology to give constant damping under any load. The company pitches it as a way to get the handling of a new vehicle back, with good traction and steering response. For a CR-V that carries passengers one day and a loaded cargo area the next, steady damping under changing weight is the main benefit.
Because the factory spring and mount move onto the new strut, this job needs a proper spring compressor or a shop that has one; our guide to spring compressors for strut jobs explains the safe styles. It suits an owner whose springs are sound and who wants a well-known damper rather than a complete corner. If the mounts or springs are rusty or noisy, a loaded assembly is the simpler path.
View Bilstein B4 22-214089 on Amazon
6. Bilstein B8 5100 24-328258: Front Shock for 2010-2022 Toyota 4Runner and 2010-2014 FJ Cruiser

- Listed for 2010-2022 4Runner, 2010-2014 FJ Cruiser
- Uses factory coil springs
- Fits OEM mounting locations
- Can be aligned to factory specs
The Bilstein B8 5100 24-328258 is a front shock for the fifth-generation Toyota 4Runner, listed for 2010 to 2022, and for the 2010 to 2014 FJ Cruiser. These are body-on-frame SUVs, so the front damper sits inside the coil spring between the control arms instead of acting as a load-bearing MacPherson strut. Check your year, drive type and any factory off-road suspension package in the fit checker before you order.
Bilstein says the shock reuses the vehicle’s factory coil springs and OEM mounting points for a direct fit, and that the SUV can still be aligned to factory specs to avoid uneven tire wear. The 5100 series uses a monotube design, which Bilstein markets for precise handling and vehicle control. Some sellers offer this part number with a ride height adjustment, so read the listing details if you plan to raise the front.
This is a pick for a 4Runner that tows a small trailer, carries a roof box or sees two-track roads on the way to the lake. Because the spring moves over from the old shock, you will need a spring compressor rated for the job, or a shop to do the transfer. Owners who want a soft, factory-like ride may find it firmer than they expect.
View Bilstein B8 5100 24-328258 on Amazon
Which Listing Fits Your SUV?
Use this table to narrow the best shocks and struts for SUVs to the one listing for your model, then check the part number against your VIN.
| Your SUV | Listing to check | Type | Watch for |
|---|---|---|---|
| 2006 to 2012 Toyota RAV4 | Monroe Quick-Strut 272276 | Loaded, front left | Confirm engine; order the right side too |
| 2010 to 2017 Chevrolet Equinox | Monroe Quick-Strut 272527 | Loaded, front left | Wheel size and trim notes in fit checker |
| 2016 to 2019 Ford Explorer | Gabriel G57819 Ultra ReadyMount | Loaded, front left | Right side is a separate part |
| 2010 to 2015 Honda Pilot | Gabriel G57695 Ultra ReadyMount | Loaded, front left | Sold one per box |
| 2007 to 2016 Honda CR-V | Bilstein B4 22-214089 | Bare twin-tube, front left | Needs a spring transfer |
| 2010 to 2022 Toyota 4Runner | Bilstein B8 5100 24-328258 | Bare coilover shock, front | Reuses factory springs; align after |
Not every front-end complaint points to the dampers. A squeak or creak over speed bumps is often a dry sway bar bushing or a worn end link, and our post on why a car squeaks when going over bumps helps you rule those out first.

Grand Rapids Winters and Heavy SUVs
Every pothole season in West Michigan sends a heavy SUV slamming into holes that a compact car might skip over. The extra mass works the strut seals harder, and once they leak, the vehicle starts to float on the highway and wallow through ramps.
Watch for oil streaks running down the strut body, cupped tire tread, a clunk from the top mount and a long, slow rebound after a dip. Our guide on how to tell if struts are bad walks through the bounce test and the visual checks.

Road salt adds work on the day of the swap. Lower strut bolts, knuckle pinch bolts and top mount nuts often rust solid on Michigan SUVs, so soak them with penetrating oil a day ahead and have new hardware on hand.
Doing the Swap, Getting Aligned and Calling a Pro
A loaded assembly is a fair home job with a good jack and stands. A bare strut or a 5100 adds a spring transfer, which is no task for a borrowed tool.
Whichever of the best shocks and struts for SUVs you install, book an alignment straight after. Gabriel’s ReadyMount strut assembly page recommends the same, because removing a strut shifts camber and toe on most crossovers.

If you would rather hand the job off, our suspension repair team in Grand Rapids replaces struts, shocks, mounts and the steering links around them. Hendrick Hoffman, the head mechanic who owns 456 AutoFix, is ASE and State of Michigan certified for steering and suspension work, and his full background is on our about us page.
More Buying Guides
Frequently Asked Questions
Do I have to replace both front struts on my SUV?
Yes, replace them as an axle pair. A new strut on one side and a worn one on the other makes the SUV lean and brake unevenly, and the listings here are sold one side at a time.
How do I know which side a single strut listing fits?
Read the title and the fit checker notes. Left means the driver side on US vehicles, and the passenger side carries a different part number that you order separately.
Are loaded struts worth it over bare struts?
On a high-mileage SUV, usually yes. A loaded unit replaces the spring, mount and boot along with the damper, and it skips the spring compressor step.
Should the rear shocks be replaced at the same time?
If they have the same mileage and show leaks or weak rebound, it makes sense. Fresh dampers at both ends keep the SUV level and stable, especially with a full cargo area.
Is your SUV wallowing over railroad crossings or diving hard at every red light? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a strut and ride check on our contact page.
If your workday lines up with our hours, park the SUV at 456 Carrier St NE once we close and leave the keys through our after-hours drop-off.
