As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A one-ton pickup that wallows after every expansion joint or lets a fifth wheel push it around in a crosswind has usually worn out its dampers. The best shocks for Ram 3500 trucks are the ones listed for your generation, drive type, rear suspension and ride height, because a 3500 is not simply a heavier 2500 underneath.
This guide sorts six listings for 1994 through 2024 trucks. If you drive a car or crossover instead, our roundup of shocks and struts for everyday commuting covers those vehicles.
Quick answer
Which shocks should a Ram 3500 owner choose?
Match the model year, 2WD or 4WD, ride height and whether the truck has rear air leveling. For a stock-height 2013 to 2018 truck, a Bilstein 4600 set is a solid all-round refresh. Leveled 4x4s need a lift-rated front shock such as the Bilstein 5100, and a Gabriel Ultra Truck suits a budget front refresh.
Our Quick Picks
Three quick picks for stock, leveled and budget trucks. All six listings are reviewed below.

Bilstein 4600 Front and Rear Set
A matched OE-height refresh for both axles of a fourth-generation truck.

Bilstein 5100 24-251747 Front Pair
Correct length for a 4×4 with a leveling kit up front.

Gabriel G63673 Ultra Truck
A straightforward OE-style front replacement for most 4×4 years.
What Sits Under a Ram 3500, Generation by Generation
Every Ram 3500 rides on plain telescopic shocks at all four corners, not struts. The springs carry the weight and the shocks only control how fast those springs move, which is why a shock swap on this truck never needs a spring compressor.
- 1994 to 2002: the second-generation Dodge Ram.
- 2003 to 2009: the third generation, with a coil-sprung solid front axle on 4WD trucks.
- 2010 to 2018: the fourth generation, with optional rear air leveling from 2013.
- 2019 and later: the current generation, again with separate rear parts for air-ride trucks.
The rear end is where the 3500 differs most from its smaller sibling. From 2014 the Ram 2500 moved to rear coil springs, while the 3500 kept leaf springs, so rear shocks rarely cross over between the two. Owners of the lighter truck should use our guide to shocks for the Ram 2500 instead.
Shopping for the best shocks for Ram 3500 dually trucks works the same way: duallies usually share part numbers with single rear wheel trucks of the same year and suspension, but cab and chassis builds can differ.
Twin-Tube, Monotube or Lift-Rated: Choosing a Damper Style
- Heavy towing: a gas-charged monotube resists fade behind a fifth wheel or gooseneck.
- Leveled or lifted: buy a shock rated for your lift, since a stock-length one tops out.
- Tight budget: a twin-tube OE-style replacement restores control for less.
Keep expectations realistic. Shocks control motion, while the springs carry the weight, so a new damper will not raise payload or cure rear sag. If the back of the truck squats under a hitch, look at the springs, airbags or the factory leveling system as well.
When owners hunt for the best shocks for Ram 3500 diesel trucks, front control matters most, because the Cummins puts extra weight over the front axle.
Best Shocks for Ram 3500: Six Listings in Detail
Each listing names its years, drive type and position, and none fits every truck. Confirm year, cab, drive, engine and rear suspension on Amazon before ordering, and replace shocks in axle pairs.
1. Bilstein 4600 24-238526 and 24-238533: Front and Rear Monotube Shock Set for 2013-2018 Ram 3500 Without Air Leveling

- Listed for 2013-2018 Ram 3500 4WD and RWD
- Front and rear part numbers in one listing
- 46 mm nitrogen monotube with floating piston
- Digressive valving, limited lifetime warranty
This Bilstein listing pairs the 24-238526 front shock with the 24-238533 rear shock for the 2013 to 2018 Ram 3500 in both 4WD and rear-drive form. The title limits it to trucks without the factory air leveling rear suspension, so check your build sheet or look for air bags above the rear axle before ordering. Confirm the quantity in the box on the listing too, since you want both sides of each axle covered.
The 4600 series is Bilstein’s stock-height line. Each shock uses a 46 millimeter monotube body with a floating dividing piston that keeps the nitrogen gas apart from the oil, which Bilstein says gives consistent, fade-free damping. The maker’s digressive valving reacts quickly to changes in the road surface, and the listing describes better lane stability in everyday and emergency driving. Bilstein covers the series with its limited lifetime warranty.
A set like this suits an owner who wants to restore a worn fourth-generation truck to a controlled factory feel without changing ride height. It fits a 3500 that tows a camper on weekends and commutes during the week. It is not meant for leveled or lifted trucks, and air-ride trucks need a different rear listing.
View Bilstein 4600 Front and Rear Set on Amazon
2. Bilstein B6 4600 24-302296: Rear Monotube Shock for 2019-2020 Ram 3500

- Listed for 2019-2020 Ram 3500 rear
- Works with the factory springs
- Monotube gas-pressure design
- Digressive valving, neoprene bushings
The Bilstein B6 4600 24-302296 is a single rear shock for the 2019 and 2020 Ram 3500, the early years of the current generation. Bilstein lists a separate rear part, 24-302302, for trucks with rear air suspension, which points this one at trucks running conventional leaf springs only. Since it is sold one per box, order two to cover the rear axle and keep both sides matched.
The listing describes Bilstein’s monotube gas-pressure design with digressive valving that responds quickly to changes in the road, plus vulcanized neoprene rubber bushings at the mounts. Bilstein says each application is fine-tuned in road testing, and it points to high gas pressure and a long service life even when pulling trailers or driving off-road. No spring change is needed, as the shock works with the original springs.
This is a sensible pick for a newer 3500 that has started to porpoise over highway joints or feels loose behind a loaded trailer. Because it keeps factory ride height, it pairs naturally with a stock front shock from the same line. It is not for trucks with the air leveling option, and it does not add load capacity, so heavy sag still needs attention at the springs.
View Bilstein B6 4600 24-302296 on Amazon

3. Bilstein 5100 24-251747: Front Monotube Shock Pair for 2013-2024 Ram 3500 4WD with 2-2.5 Inch Lift

- Listed for 2013-2024 Ram 3500 4WD front
- Sized for a 2 to 2.5 inch front lift
- Sold as a pair
- Monotube design from the 5100 series
This listing is a front pair of Bilstein 5100 series monotube shocks, part 24-251747, for the 2013 to 2024 Ram 3500 4WD with a 2 to 2.5 inch front lift. That range covers the common leveling kits sold for these trucks, which raise the nose to sit even with the bed. Two shocks come in the listing, so one order handles the whole front axle.
The reason to choose a lift-specific shock is length. When a leveling kit raises the front, a factory-length shock runs near the end of its travel, which can let the suspension top out on rebounds and leave the ride harsh. A shock built for the taller stance restores usable travel in both directions. The listing title presents the 5100 as an upgrade for ride quality and handling, and Bilstein builds the series around its monotube design.
This pair suits a 4×4 owner who has already leveled the truck, or plans to, and still uses it for towing and daily work. Because the listing gives few details beyond fit, read the fitment notes and question section on Amazon before you buy. It is the wrong part for a stock-height truck, and lifts outside that range need their own listing.
View Bilstein 5100 24-251747 Front Pair on Amazon
4. FOX 2.0 Performance 980-24-943: Rear Shock Pair for 1994-2018 Ram 3500 at Factory Height

- Listed for 1994-2018 Ram 3500 4WD and RWD
- Factory height or 0 to 1 inch rear lift
- Pair with washers, bushings and nuts
- Reuses factory shock mounting bolts
FOX part 980-24-943 is a rear pair from the 2.0 Performance series for the Ram 3500 from 1994 through 2018. The listing covers 2WD and 4WD trucks at factory height or with up to 1 inch of rear lift, which spans three generations of one-ton pickups. That wide fit is handy, but rear air leveling and cab and chassis trucks are worth checking in the fit tool before you buy.
The box includes the washers, bushings, reservoir clamps and nuts needed for the install, and the factory shock mounting bolts are reused. Shock boots, roost shields and mounting plates are sold separately, so read the listing to see whether your truck needs plates. FOX backs this pair with a limited one-year warranty against defects and premature failure, a shorter term than some rivals offer.
The 2.0 Performance series is aimed at owners who want a firmer, more controlled rear end, especially with weight on the hitch or on washboard gravel. Pair it with a front shock suited to your ride height so the truck stays balanced. It is less suited to someone after a soft factory ride, and newer trucks from 2019 on need a different listing.
View FOX 2.0 Performance Rear Pair on Amazon

5. Rough Country N3 23161_A: Nitrogen Front Shock for 2003-2024 Ram 3500 4WD with 1-2 Inch Lift

- Listed for 2003-2024 Ram 3500 4WD front
- Built for a 1 to 2 inch lift
- 54 mm body, 10-stage variable valving
- Limited lifetime replacement warranty
The Rough Country N3 23161_A is a front shock for the 2003 to 2024 Ram 3500 4WD with 1 to 2 inches of lift. That covers a long run of solid-axle trucks, from late third-generation Dodge models to current Rams. Check whether the listing ships one shock or two, since you need a matched pair across the front axle, and confirm your lift height before ordering.
Rough Country builds the N3 around a 54 millimeter body that it says cools quickly, along with 10-stage variable valving and a nitrogen charge. The listing calls out military-spec fluid rated for very cold temperatures, a spring-loaded piston rod seal and rubber bushings, plus a 36 kN tensile strength rating. Rough Country backs the shock with a limited lifetime replacement warranty.
This shock suits an owner with a modest leveling kit who wants correct travel up front without stepping up to a premium monotube. Cold-rated fluid is a sensible trait for a truck that starts on below-zero mornings in a Michigan winter. It is not the pick for a stock-height truck or for lifts beyond 2 inches, where Rough Country sells longer listings.
View Rough Country N3 23161_A on Amazon
6. Gabriel G63673 Ultra Truck: Twin-Tube Front Shock for 2003-2024 Ram 3500 4WD

- Listed for 2003-2010 Dodge Ram 3500 4WD and 2011-2024 Ram 3500 4WD
- 8.53 inch stroke, 22.3 inch extended
- Twin-tube OE replacement design
- Bolt-on install, sold as 1 pack
The Gabriel G63673 is a front shock from the Ultra Truck line, sold as a single unit. Its listing names the 2003 to 2010 Dodge Ram 3500 4WD and 2011 to 2024 Ram 3500 4WD, along with some older 1500 and 2500 4x4s. Order two for the front axle. The listing gives an 8.53 inch stroke, a 22.3 inch extended length and a 13.77 inch collapsed length, which helps when comparing it with what is on the truck now.
Gabriel describes the Ultra range as a premium OE replacement with a twin-tube design and simple bolt-on installation. On its own site the maker adds that the line uses its G-Force technology, StableSteer valving and a chromed piston rod to resist rust, with a 1 3/8 inch bore piston in most applications. The listing cross-references several other brands’ part numbers, which makes swapping from an old shock easier to check.
This is a practical choice for a work truck or a high-mileage 3500 kept at factory height, where the goal is to stop the nose from bouncing without paying for a monotube. It will not suit a leveled truck, and owners who tow heavy loads every week may prefer a firmer monotube up front.
View Gabriel G63673 Ultra Truck on Amazon
Which Listing Fits Your Truck
Use this shortlist, then check the part number against your VIN.
| Your Ram 3500 | Listing to check | Position | Watch for |
|---|---|---|---|
| 2013 to 2018, stock height, no air leveling | Bilstein 4600 set 24-238526 / 24-238533 | Front and rear | Not for rear air suspension |
| 2019 to 2020, stock rear springs | Bilstein B6 4600 24-302296 | Rear | Air-ride trucks need 24-302302 |
| 2013 to 2024 4WD, 2 to 2.5 inch level | Bilstein 5100 24-251747 pair | Front | Lift range must match |
| 1994 to 2018, tows heavy | FOX 2.0 Performance 980-24-943 pair | Rear | Mounting plates sold separately |
| 2003 to 2024 4WD, 1 to 2 inch lift | Rough Country N3 23161_A | Front | Check quantity per box |
| 2003 to 2024 4WD, budget refresh | Gabriel G63673 Ultra Truck | Front | Sold as a 1 pack |
Not every noise means a shock has failed. A squeak over speed bumps is often a dry bushing or sway bar link; our post on why a car squeaks when going over bumps sorts those out.

Salt, Potholes and Trailers in West Michigan
Grand Rapids winters are hard on a one-ton. Freeze-thaw potholes hit a loaded truck harder, and road salt attacks shock bodies, rods and mounting bolts all season.
Watch for a second or third bounce after a dip, a trailer that starts the truck rocking, cupped tires and oily shock bodies. Gabriel’s Ultra shock page notes that a light, even mist of oil is normal, while streaks mean a leak. Our checklist on how to tell if struts are bad uses the same tests, and they apply to shocks too.

Salt also slows the job, since lower shock bolts can seize in their sleeves. Soak them with penetrating oil the day before and have new hardware ready.
Fitting Ram 3500 Shocks and When to Book a Shop
Shock replacement is a friendly job on a heavy truck, since the springs stay put. You still need a jack rated for the weight and solid stands; our list of jack stands built for pickups helps there. Support the axle so it cannot drop and strain brake lines.
Whichever of the best shocks for Ram 3500 owners you choose, check the alignment after leveling the front. A new front shock also will not fix a steering wobble caused by worn track bar bushings or tie rod ends, so inspect those parts at the same time. Coverage terms vary by brand, and the Bilstein warranty promise for North American buyers lists both the B6 4600 and B8 5100 lines under its limited lifetime terms.

To hand the job off, use our suspension repair service in Grand Rapids for shocks and steering parts. Hendrick Hoffman, who runs the shop, is ASE and State of Michigan certified in steering and suspension, and his background is on our about us page.
More Buying Guides
Frequently Asked Questions
Do Ram 3500 dually trucks need different shocks?
Usually not by wheel count alone. Shock part numbers follow the year, drive type and rear suspension, but cab and chassis trucks and flatbed builds can differ, so confirm your exact truck in the fit checker.
Should I pick Bilstein 4600 or 5100 shocks for a Ram 3500?
The 4600 is built for factory ride height. Choose a 5100 listing when the front is leveled or lifted within the range named on that listing, since a stock-length shock can top out on a raised truck.
Will new shocks stop my diesel 3500 from sagging with a fifth wheel?
No. Shocks control bounce and sway, but the springs carry the load. Sag under a hitch points to tired leaf springs, a weak air leveling system or simply a heavy pin weight.
Is your Ram 3500 floating on the highway or bucking behind a trailer? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a heavy truck suspension inspection through our contact page.
If the truck is busy working all day, park it at our Carrier St NE shop in Grand Rapids once the workday is done and leave it with our after-hours drop-off.
