456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Battery Safe Lifting: Choosing the Best Car Jack for Model Y

best car jack for model y: winding road through hilly landscape under cloudy skies

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A Model Y carries its high-voltage battery across most of the floor, so the spot you put a jack matters more than on a typical gas SUV. The best car jack for Model Y owners is really a pair: a floor jack with enough reach and capacity, plus a pad or puck that seats in Tesla’s lift points.

Below: where the car can be lifted, what to look for and six options. If you also lift lower sedans, our roundup of low profile floor jacks for cars covers the wider field.

Quick answer

What should you lift a Model Y with?

Use a low profile floor jack rated for an SUV, such as the VEVOR 2.5 ton aluminum model, with a lift puck like the BANGTING set fitted into the designated body lift point. Never lift on the battery or side rails, and set the car on jack stands before reaching underneath.

Our Quick Picks

Three quick picks: a floor jack for home jobs, a puck set for the lift points and a compact kit for the trunk. All six are reviewed below.

VEVOR 2.5 Ton Aluminum Jack product photo
Home garage pick

VEVOR 2.5 Ton Aluminum Jack

2.5 ton · 3.74-18.7 in · aluminum and steel

A lighter racing-style jack that VEVOR lists for compact SUVs.

SuitsWheel swaps and rotations at home
View on Amazon →
BANGTING Tesla Jack Pad Set product photo
Lift point pucks

BANGTING Tesla Jack Pad Set

4-pack · rubber · O-ring retention

Pucks that plug into the lift points and cushion the jack saddle.

SuitsFloor jacks, stands and shop lifts
View on Amazon →
ALIXUEQIN Tesla Scissor Jack Kit product photo
Trunk kit

ALIXUEQIN Tesla Scissor Jack Kit

2.5 ton · 5.3-15.3 in · scissor

A compact scissor jack kit with a Tesla-shaped pad.

SuitsRoadside flats and spare wheel changes
View on Amazon →

Where a Model Y Can and Can’t Be Lifted

Tesla is specific here. The owner’s manual says lift pads go under the designated body lift points only, and that those are the only approved lifting points for the car. The battery and the side rails are off limits.

There are four of these points, and pad makers describe a round hole at each one that a puck plugs into. Tesla also notes that its drawing is a guide, so look at your own car to find the exact spot before you slide a jack under it.

  • Lift here: the four designated body lift points, with a pad or puck between the jack saddle and the car.
  • Never here: the flat battery case, the side rails along the rocker, suspension arms or the plastic underbody covers.
  • Not while plugged in: Tesla warns never to raise the car with the charge cable connected, even if it isn’t charging.

What to Look For in a Jack and a Puck

The battery makes a Model Y heavier than its size suggests. Choose the jack for that weight and the puck for your model year.

  • Capacity: a 2.5 or 3 ton floor jack leaves comfortable margin for lifting one corner or one side. Check the curb weight on your door jamb label and stay well inside the rating.
  • Lift range: a saddle that starts low slides under the car easily, even on a flat tire. The top of the range has to clear a tire off the ground with a puck in place.
  • Puck fit: some adapters list every year, including the 2025 refresh often called Juniper, and others stop at 2024. Read the fitment line before you buy.

If the jack is your first piece of garage gear, our list of starter car maintenance tools for beginners fills in the rest of the kit.

Best Car Jack for Model Y: Six Options Up Close

Three are floor jacks, two are lift point adapters and one is a compact scissor jack kit for the trunk. A floor jack and a puck together make a complete home setup.

1. VEVOR Low Profile Floor Jack: 2.5 Ton Aluminum and Steel with Dual Piston Pump

VEVOR 2.5 Ton Aluminum Jack product photo
Key features
  • 2.5 ton (5,500 lb) rated capacity
  • 3.74 to 18.7 in lifting range
  • Dual piston quick lift pump
  • Rotating saddle with rubber pad

This VEVOR racing-style floor jack mixes an aluminum frame with steel parts to keep the weight manageable while holding a 2.5 ton (5,500 lb) rating. VEVOR lists it for sports cars, sedans and compact SUVs, which is the class a Model Y falls into. The lifting range runs from 3.74 inches up to 18.7 inches, so it slips under the car easily and still has height left to clear a tire.

The dual piston pump is the main convenience. VEVOR says the jack reaches full height in about six pumps with no load, which shortens each lift during a four-wheel swap. Lowering is controlled by turning the long handle counterclockwise, and the rotating saddle carries a non-slip rubber pad on top. Two swivel casters and two fixed wheels let you roll it into place on a smooth garage floor.

Pair it with a lift puck so the saddle presses on the designated lift point rather than on the battery or side rail. The rubber pad alone is not a substitute for a puck on this car. It suits owners who lift a few times a year and want a jack that is easy to carry. The maker notes it is for lifting only, so plan on jack stands for any work underneath.

View VEVOR 2.5 Ton Aluminum Jack on Amazon

2. Henf Pro Steel Low Profile Racing Floor Jack: 3 Ton with 3.3 to 18.5 in Lift

Henf Pro Steel 3 Ton Jack product photo
Key features
  • 3 ton (6,600 lb) rated capacity
  • 3.3 to 18.5 in lifting range
  • Dual piston pump, all-steel build
  • Listing states ANSI/ASME PASE

Henf’s Pro Steel jack is an all-steel, low profile racing design rated at 3 tons, or 6,600 pounds. Its saddle starts at 3.3 inches and climbs to 18.5 inches, a range that covers low sedans, the Model Y and many larger SUVs. For a household with an electric crossover and a gas truck, that extra margin lets one jack cover both.

A dual piston pump speeds up the climb, and Henf says it lifts several times faster than a single pump design. The saddle turns 360 degrees, carries a rubber pad and can be removed and replaced. A foam bumper on the handle helps protect paint if the handle swings toward the car. The listing also states that the jack meets ANSI/ASME PASE safety standards, the standard used for portable automotive service equipment.

The tradeoff is weight. A steel frame is heavier than an aluminum one, so this jack is better at home in a garage than in the trunk. On a Model Y, set a puck in the lift point and center this jack’s saddle under it before lifting. Like every floor jack, it is meant to raise the car, not hold it, so a pair of stands belongs next to it.

View Henf Pro Steel 3 Ton Jack on Amazon

serene misty morning view on a rural dirt path

3. BANGTING Lifting Jack Pad Set: 4-Pack Rubber Lift Pucks for Model Y and Juniper

BANGTING Tesla Jack Pad Set product photo
Key features
  • Four rubber lift pucks
  • Lists Model 3, S, X, Y and Y Juniper
  • O-ring holds each puck in the hole
  • Storage case included

A puck set is the piece that turns an ordinary floor jack into a safe Model Y tool. BANGTING’s kit includes four rubber pucks that plug into the car’s jack points, and the listing covers the Model 3, S, X and Y, including the Model Y Juniper. Each puck carries a rubber O-ring, so you can push it into the hole first and then line up the jack without it dropping out.

The rubber body gives the jack saddle a flat, non-slip surface at the lift point. BANGTING says it helps keep frame rails and pinch seams from bending and protects painted or coated parts underneath. Four pucks matter if you use a two-post lift, which needs all four points at once, or if you set the car on stands after jacking.

The storage case keeps the set together in the frunk or trunk. That is handy at a tire shop, where you can hand the pucks to the tech so the car goes up at the right spots. Rubber pucks wear over time, so check them for cracks before each use. A puck does not add capacity, so the jack and stands still need the right ratings.

View BANGTING Tesla Jack Pad Set on Amazon

4. LRNJ Motorworks Lift Jack Point Pad Adapter: Machined Aluminum for Model Y 2020-2024

LRNJ Motorworks Aluminum Adapter product photo
Key features
  • CNC machined 6061-T6511 aluminum
  • 2-inch base diameter
  • Delrin washer and retaining O-ring
  • Lists Model Y 2020-2024 only

LRNJ Motorworks makes this jack point adapter from 6061-T6511 aluminum, machined on a CNC mill to fit the factory jack point hole. The listing covers the Model 3 from 2017 to 2024 and the Model Y from 2020 to 2024. It does not list the refreshed 2025 Model Y, so owners of the newer car should look at a set that names it.

Unlike a rubber puck, this adapter stays rigid under load. A Delrin acetal washer sits between the aluminum and the car to prevent metal-on-metal contact, and a rubber O-ring on the locating shank holds it in the hole. The base is 2 inches across and grooved for grip when you pull it out. LRNJ says it works with most floor jacks that have a saddle 2 inches or wider.

It is sold as a single adapter, which is enough for lifting one corner with a floor jack. If you want to put the car on stands at other points, or hand a full set to a shop, you would need more than one. LRNJ notes that it only fits cars with a 1-inch round jack point hole, so check yours before ordering. All materials are listed as sourced and made in the USA.

View LRNJ Motorworks Aluminum Adapter on Amazon

long empty road leads to distant snow-capped mountains under a dramatic sky

5. TONDA Low Profile Floor Jack: 2.5 Ton Steel with 3.35 to 14.57 in Lift

TONDA 2.5 Ton Low Profile Jack product photo
Key features
  • 2.5 ton (5,000 lb) rated capacity
  • 3.35 to 14.57 in lifting range
  • Built-in overload protection
  • Carrying handle, detachable long handle

TONDA’s floor jack is a compact steel unit rated at 2.5 tons, or 5,000 pounds. It starts at 3.35 inches and lifts to 14.57 inches. That top height is lower than the two racing jacks above, so it fits owners who mostly change wheels rather than reach high under the car, and who want something easier to store.

Two large steel wheels and two swivel casters move it across the floor, and a built-in carrying handle plus a detachable long handle make it easier to lift into a cabinet or a corner. TONDA lists an integrated overload protection system and a sealed hydraulic design, plus a protective coating meant to resist scratches and corrosion in a garage. The maker names tire changes, brake service and routine maintenance as its intended jobs.

With a puck in place, the lower maximum height leaves less room to spare, so measure from the floor to the lift point and add the puck and the tire clearance you need. If the numbers work for your car, it is a tidy, simple option. TONDA asks that it be used on a stable surface, and as with any jack, stands go under the car before you work.

View TONDA 2.5 Ton Low Profile Jack on Amazon

6. ALIXUEQIN Scissor Car Jack Kit: 2.5 Ton with Tesla Jack Pad and Storage Bag

ALIXUEQIN Tesla Scissor Jack Kit product photo
Key features
  • 2.5 ton (5,512 lb) rated capacity
  • 5.3 to 15.3 in lifting range
  • Tesla pad plus universal pad
  • Ratchet, lug wrench, sockets and gloves

A floor jack stays in the garage, so this kit covers the roadside. ALIXUEQIN’s scissor jack is made from cold-rolled steel, rated at 2.5 tons (5,512 lb) and lists the Model Y, 3, S and X. Its lifting range runs from 5.3 to 15.3 inches, and an enlarged base helps keep it steady on a hard surface.

The kit ships with two pads: one shaped for Tesla jack points and one universal pad for other cars. A ratchet wrench drives the screw so you don’t have to crank by hand the whole way, and the bag also holds a lug wrench, two sockets and a pair of gloves. Everything packs into a storage bag that fits in the trunk or frunk.

This is an emergency tool, not a replacement for a floor jack and stands. A scissor jack has a small footprint, so use it only on firm, level ground, chock the opposite wheel and never put any part of your body under the car. It makes most sense if you carry a spare wheel or plan to meet a tire service and want a way to lift the car at the right point.

View ALIXUEQIN Tesla Scissor Jack Kit on Amazon

Picking the Right Setup for Your Garage

The table matches common jobs with a setup that suits them.

JobSetup that fitsAlso bring
Seasonal winter wheel swap2.5 or 3 ton floor jack plus a puckTwo jack stands and a torque wrench
Tire rotation at homeFloor jack plus a four-pack of pucksFour jack stands, or lift one side at a time
Flat tire away from homeScissor jack kit with a Tesla padWheel chocks and a flat board
Car going to a shop liftPuck set in the trunkTell the tech where the lift points are
Model Y jacking setups matched to common home and roadside jobs

For most garages, the best car jack for Model Y work is a dual piston floor jack in the 2.5 to 3 ton range with a rubber puck. If you also own a larger SUV, our guide to floor jacks for SUVs covers taller lift ranges.

tranquil road winds through a colorful autumn forest with vibrant foliage

Lifting a Model Y Step by Step

Follow this order every time:

  1. Unplug and park: disconnect the charge cable, put the car in Park on flat concrete and chock a wheel on the opposite corner.
  2. Seat the puck: push the puck into the lift point until the O-ring holds it, then center the jack saddle under it.
  3. Lift slowly: watch the puck as the weight comes on. If it tilts, lower and reset.
  4. Support it: set a jack stand at an approved spot before you reach under the car or pull a wheel.
  5. Lower with care: remove the stand and open the release valve slowly.

Tesla’s Model Y jacking and lifting instructions show the lift point locations and add that damage from lifting elsewhere is not covered by the warranty. For low, wide stands that fit under the car, see our guide to jack stands for low cars.

idyllic rural landscape with a dirt path and fields at sunset

West Michigan owners usually lift twice a year, once to fit winter tires before the snow and again in spring. Road salt collects around the lift points over the winter, so brush the area clean before you seat a puck.

When the Job Belongs in a Shop

If you spot a torn boot, a leaking shock or uneven wear on the tires while the car is up, that points to suspension parts that need a proper inspection. Our suspension repair service in Grand Rapids handles that work.

deserted rural road stretches into the horizon during a serene sunset

Electric cars still have brakes, cabin filters, tires and fluids on a maker’s schedule. Our factory scheduled maintenance in Grand Rapids keeps the car on the intervals its maker sets.

Frequently Asked Questions

Do I need jack pads to lift a Model Y?

A pad or puck is the simplest way to keep the jack on the lift point. It plugs into the hole, gives the saddle a flat rubber or aluminum surface and helps stop the jack from sliding toward the battery.

Can I use a regular floor jack on a Model Y?

Yes, if it is rated for the car’s weight, reaches the lift point and lifts high enough to clear the tire. Put a puck between the saddle and the car, and use jack stands before working underneath.

Do the same pucks fit the newer Model Y Juniper?

Some do and some don’t. Several rubber sets list the refreshed car, while others, such as the LRNJ aluminum adapter, list 2020 to 2024 only. Match the listing to your model year before ordering.

What capacity is the best car jack for Model Y lifting?

A 2.5 or 3 ton floor jack covers one corner or one side with room to spare. Higher capacity mostly adds weight, so pick the lift range and saddle size first.

Found something odd under your Model Y while it was in the air? Call 456 AutoFix at 616-279-3832 between 8am and 5pm, Monday through Friday, or request a visit through our contact page.

If daytime doesn’t work, our after-hours drop-off lets you leave the car at 456 Carrier St NE in Creston and we’ll take it from there.