456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Cummins, Duramax or Power Stroke? The Best Engine Block Heater for Diesel Trucks

best engine block heater for diesel trucks: truck in a snowy parking lot at night

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A diesel pickup left in the driveway overnight in a Grand Rapids January can crank slowly, smoke on startup and take ages to put out cab heat. The best engine block heater for diesel trucks is the one built for your engine family, whether that is a Cummins, a Duramax or a Power Stroke, fed by a cord that survives a winter of salt.

Many heavy-duty diesel pickups were sold with a factory block heater, so the job is often replacing a dead element or a worn cord. Below are seven products: three engine-matched heaters, two cords, a magnetic add-on and an outdoor extension cord. For gas engines and the general heater styles, see our guide to choosing an engine block heater.

Quick answer

Which block heater should a diesel truck owner buy?

Buy the heater made for your engine. Cummins owners can look at the Zerostart 3500022, earlier 6.6L Duramax trucks take a 3100130-style element, and the 6.7L Power Stroke uses a 27mm heater like the HFM unit. If the element still works, a new cord may be all you need.

Our Quick Picks

One quick pick for each of the big three diesel engine families. All seven products are reviewed below.

Zerostart 3500022 product photo
Cummins pick

Zerostart 3500022

750W · 3/4 in NPT

Threads into the block and warms the coolant from inside the engine.

SuitsCummins-powered pickups parked outside
View on Amazon →
OWNDR 3100130 Duramax Heater product photo
Duramax pick

OWNDR 3100130 Duramax Heater

1000W · replaces 3100130

A like-for-like element for the earlier 6.6L Duramax V8.

Suits2001-2015 Chevy and GMC Duramax owners
View on Amazon →
HFM 6.7L Power Stroke Heater product photo
Power Stroke pick

HFM 6.7L Power Stroke Heater

1000W · 27mm

Sized for the 6.7L Power Stroke in Super Duty pickups.

SuitsF-250 and F-350 diesel owners
View on Amazon →

Why a Cold Diesel Struggles More Than a Gas Engine

A diesel has no spark plugs. It lights its fuel with the heat created by squeezing air hard in the cylinder, and a block sitting at single-digit temperatures soaks up much of that heat. Glow plugs or an intake grid heater help, but they work for seconds while the heavy iron around them stays cold.

A block heater attacks the problem from the other side. By warming the coolant for a few hours before you leave, it keeps the block, head and oil well above outdoor temperature. That means quicker starts, less strain on the batteries and cab heat sooner.

Five Checks Before You Order a Diesel Heater

  • Is a heater already there? Look for a cord near the grille or front bumper, and test it before buying anything.
  • Engine and port: Cummins, Duramax and Power Stroke heaters use different fittings, which can change between engine generations.
  • Cord or element: a multimeter across the cord’s prongs tells you whether the element works.
  • Wattage: 750 to 1000 watts is typical for these engines, which takes a big share of a 15 amp household circuit.
  • The outlet: a grounded outdoor outlet, ideally GFCI protected, and a heavy-gauge outdoor cord if the truck parks away from the house.

Choosing the best engine block heater for diesel trucks starts with fit. Run your exact year, model, engine and trim through the Amazon fit checker before buying. No single heater fits every diesel pickup.

Best Engine Block Heater for Diesel Trucks: Seven Picks by Engine

Each product below is listed on Amazon US. Treat the years named in each listing as the limit and confirm your truck before ordering.

1. Zerostart 3500022 Immersion Heater: 750W, 3/4 Inch NPT for Cummins

Zerostart 3500022 product photo
Key features
  • 750 watts at 120 volts
  • 3/4 inch NPT thread
  • 6 ft cord included
  • CSA approved

The Zerostart 3500022 is an immersion heater that threads into a 3/4 inch NPT port on the engine block and warms the coolant from inside the water jacket. The listing names Cummins and Paccar applications and points buyers to the Zerostart catalog for exact engines. It runs at 750 watts on a 120 volt outlet, ships with a 6 foot cord and is CSA approved.

Other Cummins-fit listings on Amazon name the 5.9L and 6.7L engines with this same 3/4 inch thread, so it is a common choice when a Ram owner finds the original element has stopped warming. Because the element sits in the coolant, heat spreads through the block and head, which helps the cylinders reach the temperature that compression ignition depends on.

Replacing it means draining coolant below the port, unthreading the old element, sealing the new one and then refilling and bleeding air out of the system. Confirm your year, engine and port with the Amazon fit checker and the Zerostart catalog before you order. It is not a match for Duramax or Power Stroke engines, which use different fittings.

View Zerostart 3500022 on Amazon

2. OWNDR 3100130 Replacement Block Heater: 1000W for 2001-2015 Duramax 6.6L

OWNDR 3100130 Duramax Heater product photo
Key features
  • 1000 watts at 120 volts
  • Replaces part 3100130
  • Listed for 6.6L Duramax V8
  • Direct replacement install

This OWNDR heater is built as a replacement for the 3100130 part number used on the 6.6L Duramax V8. The listing names Chevrolet and GMC 6.6L engines from 2001 to 2008 and Duramax 6.6L diesels from 2007 to 2015. It is rated at 1000 watts on 120 volts, and listings for the 3100130 part describe a 40mm round fitting.

The higher wattage suits a big-displacement diesel sitting in an open driveway, where there is a lot of iron to warm before the engine will start easily. Heat goes straight into the coolant, so both the engine and the cab heater benefit once you turn the key. The listing calls it a direct replacement, which matters to owners whose original element has burned out while the cord and wiring are still in good shape.

The listing stops at the 2015 model year, so later 6.6L engines and the 3.0L Duramax are outside what it names. Check the engine code in your owner’s manual and run the truck through the Amazon fit checker before ordering. Swapping the element is a coolant-drain job, and access varies by model year, so a shop is a sensible option if the port is hard to reach.

View OWNDR 3100130 Duramax Heater on Amazon

Mechanic working on a yellow truck cab

3. HFM Engine Block Heater: 1000W, 27mm for 6.7L Power Stroke Super Duty

HFM 6.7L Power Stroke Heater product photo
Key features
  • 1000 watts at 120 volts
  • 27mm diameter fitting
  • Listed for 6.7L Power Stroke
  • Made in USA per listing

HFM’s heater is listed for the 6.7L Power Stroke V8 in the 2011 to 2019 Ford F-350 and the 2011 to 2024 F-250 Super Duty. It fits a 27mm port, draws 1000 watts at 120 volts and is listed as made in the USA. That gives Super Duty owners a part sized for their own engine.

When a Super Duty stops warming on a cold night, test the outlet and cord first. If both check out, the element itself is the next suspect, and this listing is a like-for-like swap for it. A 1000 watt heater brings coolant temperature up faster than a low-wattage add-on, which counts on a truck that sits all night at a jobsite or in a driveway.

The listing names only these trucks, so confirm year, model and engine with the Amazon fit checker before buying, because other Ford diesels and some chassis cab versions may differ. Installation means draining coolant and working low on the side of the block. Check whether a cord is included for your truck, and if it isn’t, pair the heater with the matching Power Stroke cordset.

View HFM 6.7L Power Stroke Heater on Amazon

4. Zerostart 3600008 Replacement Cordset: 6 ft, 16/3 HPN for Heavy-Duty Heaters

Zerostart 3600008 Cordset product photo
Key features
  • 6 ft, 16 gauge cord
  • 16/3 HPN wire
  • Silicone right-angle connector
  • 120 volt, 15 amp plug

The cord is the part of a block heater that takes the most abuse, since it hangs out of the grille through salt, slush and the occasional rodent. Zerostart’s 3600008 is a 6 foot replacement cordset for heavy-duty immersion heaters and engine block heaters. It has a standard 120 volt, 15 amp plug on one end and a silicone right-angle female connector on the other, joined by 16/3 HPN wire.

Aftermarket listings commonly cross this style of cord to Cummins-powered Ram trucks and to the Ford 6.0L, 6.4L and 7.3L Power Stroke heaters with the same pin layout. Zerostart gives the pin spacing as 0.360 inch and the pin diameter as 0.138 inch, so you can compare it with the socket on your heater before ordering.

Replacing a cracked cord is a much quicker job than replacing a heater that still works, because you don’t drain any coolant. It does not fit the Duramax connector, which uses its own cord. Route the new cord away from the exhaust and belts,. Scorched pins or a melted connector can mean a poor connection, so check the heater socket and the outlet too.

View Zerostart 3600008 Cordset on Amazon

Mechanics working under a heavy truck

5. Tecreddy Duramax Block Heater Cord: 6 ft 16AWG, Replaces 84303149

Tecreddy Duramax Heater Cord product photo
Key features
  • 6 ft, 16 gauge copper wire
  • Replaces 84303149 and 19301659
  • Listed for 2001-2017 6.6L Duramax
  • 120 volts, 15 amps

Tecreddy’s cord is a 6 foot, 16 gauge replacement for the 6.6L Duramax block heater. The listing says it fits all 2001 to 2017 and most 2018 Duramax 6.6L diesels in any vehicle. It crosses to several GM part numbers, including 84303149 and 19301659, and it is rated at 120 volts and 15 amps with 16/3 HPN copper wire.

On many pickups the plug end of the cord sits near the bumper or grille, where winter grime, salt spray and daily plugging wear out the prongs and the jacket. A cord with a cracked jacket or loose prongs is a common reason a heater seems dead when the element itself is fine. Swapping the cord is a far smaller job than changing the heater, because the cooling system stays closed.

Match the model year carefully, since the listing says most 2018 trucks rather than all of them. Listings for 2019 and later Silverado and Sierra Duramax trucks name a different cord, part 84564686, so newer owners should look for that one instead. If the heater still won’t warm with a new cord, the element or the outlet needs a closer look.

View Tecreddy Duramax Heater Cord on Amazon

6. Zerostart 3400021 Magnetic Heater: 300W with Built-In Thermostat

Zerostart 3400021 Magnetic Heater product photo
Key features
  • 300 watts at 120 volts
  • Thermostat set at 266°F
  • For steel, non-aluminum surfaces
  • 6 ft cord, CSA certified

The Zerostart 3400021 is a 300 watt magnetic heater with a built-in thermostat that the listing sets at 266°F. It holds onto steel or iron surfaces, not aluminum, and comes with a 6 foot cord. Zerostart lists it for oil pans, transmissions, engine blocks and hydraulic systems, and it is CSA certified for safety.

On a diesel pickup it works as a supplement to a coolant heater rather than a substitute for one. Placed on a steel oil pan, it warms the oil so it moves more freely at startup, which eases cranking on a cold morning and takes some load off the batteries. It also moves easily between a truck, a tractor, a generator and other equipment, which suits owners who run more than one diesel engine around the property.

Before buying, hold a fridge magnet to your oil pan, because many newer pickups use aluminum pans where this heater won’t hold. Clean the spot first so the magnet sits flat, and keep the cord well clear of the exhaust, belts and steering parts. Take it off before you drive, since it is designed as a removable heater rather than a permanent mount.

View Zerostart 3400021 Magnetic Heater on Amazon

7. POWGRN 12/3 Outdoor Extension Cord: 25 ft, 15A, Cold-Flexible Jacket

POWGRN 25 ft 12/3 Cord product photo
Key features
  • 25 ft, 12 gauge, 3 conductor
  • 15 amps, 1875 watts
  • SJTW jacket, ETL listed
  • Lighted socket end

A heater is only as good as the power that reaches it, and a thin indoor cord is the wrong choice for a 750 to 1000 watt load outdoors. POWGRN’s 25 foot cord uses 12 gauge, three-conductor SJTW wire rated at 15 amps and 1875 watts, with standard grounded NEMA 5-15 ends. It is ETL listed and has a lighted end that shows when power is reaching it.

The listing says the jacket stays flexible down to -58°F, which helps when you are uncoiling it in the dark on a January morning. Both ends have strain relief, and a hook on the socket end makes plugging and unplugging easier with gloves on. Heavier 12 gauge wire also keeps voltage drop low over 25 feet, so the heater runs closer to its full output.

Use one continuous cord rather than chaining several together, and uncoil it fully, as the listing advises. Plug into a grounded outdoor outlet, ideally one with GFCI protection, and keep the connection up off wet ground and snow. For a longer run, a closer outlet or a heavier cord is the safer choice than adding another length.

View POWGRN 25 ft 12/3 Cord on Amazon

Matching Heater and Cord to Your Engine

The picks by engine family, to narrow the search before you confirm part numbers.

EngineHeater pickCord pickWatch for
Cummins 5.9L and 6.7L (Ram)Zerostart 3500022, 3/4 inch NPTZerostart 3600008Confirm the thread with the Zerostart catalog
Duramax 6.6L, 2001-2015OWNDR 3100130 replacementTecreddy 84303149 (through most 2018)2019 and later trucks use a different cord
Power Stroke 6.7L Super DutyHFM 27mm, 1000WCheck whether the listing includes oneListing names 2011-2019 F-350, 2011-2024 F-250
Any truck with a steel panZerostart 3400021 magnetic add-onBuilt-in 6 ft cordWon’t hold on aluminum
Diesel block heater and cord picks by engine family
Blue house with a snowy driveway

A heater is one part of getting a diesel through the cold months. Fresh coolant at the right mix matters, since every heater here works through it, and winter fuel and healthy batteries do the rest. Our winter car maintenance checklist covers the full list, and the winter car accessories we recommend round out a truck kit.

Plugging In a Diesel Through a West Michigan Winter

Even the best engine block heater for diesel trucks doesn’t need to run all night. On diesel owner forums, two to three hours on a timer is the common pattern, because most of the warming happens early and the gain levels off after that. Your owner’s manual may also give a temperature at which the maker suggests plugging in, so follow it.

A warm diesel also cuts the urge to idle the truck in the driveway for twenty minutes. The US Department of Energy’s Alternative Fuels Data Center on idle reduction notes that idling wastes fuel and increases engine wear, and that US vehicles burn more than 6 billion gallons of diesel and gasoline a year without moving. See our post on how long to warm up your car in winter.

Yellow house after a snowfall

Road salt and slush are hard on the plug end of the cord, so check it each fall for cracked insulation, bent prongs or chew marks. Replace a damaged cord rather than taping it, and use a timer rated for your heater’s full wattage.

Signs Your Heater Setup Needs a Professional Look

A breaker that trips every time you plug in, a burning smell, or coolant weeping from around the heater port all need attention before the next cold night.

Mechanic climbing into the cab of a blue truck

If the truck still cranks slowly with a working heater, look at the batteries, starter and glow plug or grid heater system, which our guide to a car not starting in cold weather walks through. Our shop handles car electrical repair in Grand Rapids for body and engine electronics, and our check engine light diagnostics can read stored codes and point to the cause.

Frequently Asked Questions

How long should I plug in a diesel block heater?

Two to three hours before you leave is the common choice among diesel owners, with a little longer on the coldest mornings. An outdoor timer rated for your heater’s wattage saves you from running it all night.

What is the best extension cord for a diesel block heater?

Use a single outdoor-rated, grounded cord heavy enough for the load, such as a 12 gauge cord for a 25 foot run to a 750 or 1000 watt heater. Avoid thin indoor cords and chains of several cords.

Does a block heater stop diesel fuel from gelling?

No. It warms the coolant and the engine, not the fuel tank or lines. For very cold weather, rely on winter-blend diesel and keep the tank from sitting near empty.

Diesel pickup giving you hard starts this winter? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or book a visit through our contact page.

Can’t get away during the workday? Leave the truck with us using our after-hours drop-off. We’re at 456 Carrier St NE in Creston.