456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

From Camaro to Silverado HD: Choosing the Best Jack Stands for Chevy

best jack stands for chevy: peaceful dirt road winding through a dense pine forest under a soft

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

Chevrolet builds everything from a low-slung Camaro to a heavy-duty Silverado, and no single pair of stands suits that whole range. The best jack stands for Chevy owners are the ones matched to their own car or truck: short enough to slide under a coupe, or tall and strong enough for a full-size pickup.

Below we sort the lineup by height and weight, then look at five pairs in detail. If you want the general basics on locks, saddles and ratings first, read our guide to jack stands for the home garage.

Quick answer

Which jack stands fit a Chevy car or truck?

Size them to the vehicle. A Camaro or Malibu works well with short 3 ton stands such as the Jackco aluminum pair, which starts at 9.5 inches. A Silverado 1500 or Tahoe needs a taller 6 ton pair like the Powerbuilt 647511, and heavy-duty trucks call for 10 to 12 ton stands.

Our Quick Picks

Three pairs that cover the Chevy range, from a low Camaro to a heavy-duty pickup.

Jackco 3 Ton Aluminum Jack Stands product photo
Low cars

Jackco 3 Ton Aluminum Jack Stands

3 ton pair | 9.5 to 15.25 in.

Light aluminum stands with a low starting height.

SuitsCamaro, Malibu and other low Chevy cars
View on Amazon →
Powerbuilt 647511 6 Ton Jack Stands product photo
Half-ton trucks

Powerbuilt 647511 6 Ton Jack Stands

6 ton pair | 15-1/2 to 23-1/2 in.

Tall ratchet stands with a wide four-point base.

SuitsSilverado 1500, Tahoe, Colorado
View on Amazon →
Strongway 12 Ton Jack Stands product photo
Heavy duty

Strongway 12 Ton Jack Stands

12 ton pair | double locking

Heavy stands with a pin backup for big trucks.

SuitsSilverado HD, Suburban, work trucks
View on Amazon →

One Badge, Very Different Undersides

A sixth-generation Camaro, sold from the 2016 to 2024 model years, sits close to the ground, and track-minded trims like the 1LE carry aero parts low on the nose. Unibody cars such as the Camaro, Malibu and Equinox are usually supported at reinforced pinch welds or other points the manual marks. A stand that starts too tall simply will not fit under them once the jack is out of the way.

Silverado pickups, the Tahoe and the Suburban are a different story. They ride on separate frames, weigh far more and leave their frame rails well above the floor. Here the top of the stand’s range matters more than the bottom, and capacity becomes the first number to check.

Chevrolet publishes free owner’s manuals for current and older models on its manuals and guides page. Download the one for your year and model and find the section on jacking and lifting before you buy anything, since it shows exactly where your vehicle should be held up.

Sizing Stands to Your Chevrolet

  • Measure first: raise one corner until the tire just leaves the floor, then measure from the slab to the support point. Choose a stand whose range puts that figure near the middle of its travel.
  • Read the rating carefully: some makers quote capacity per stand and others quote the pair. Compare both against the gross vehicle weight on your door jamb label.
  • Pick a lock you can see: ratchet stands adjust quickly, while pin-type stands lock with a steel pin through the column. Many ratchet designs add a second pin as a backup.
  • Mind the saddle: a narrow or recessed saddle suits a pinch weld, and a wide saddle spreads load on a flat truck frame.

For a Camaro 1LE, the usual routine is a low-profile floor jack at the point the manual shows, then short stands set at the next approved support. Some owners drive onto low ramps first to get the jack in, and our car ramps for Chevy roundup covers that step.

Best Jack Stands for Chevy: Five Pairs in Detail

The five pairs below run from light aluminum stands for low cars to pin-type stands made for heavy trucks. Capacities and heights come from each Amazon listing, and where a listing leaves a number out, we leave it out too.

1. Jackco 3 Ton Aluminum Jack Stands: 9.5 to 15.25 in. Range, Under 5 lb Each

Jackco 3 Ton Aluminum Jack Stands product photo
Key features
  • 3 ton capacity, sold as a pair
  • Aircraft-grade aluminum build
  • 6 positions from 9.5 to 15.25 in.
  • 2 in. saddle, under 5 lb per stand

The Jackco 3 Ton Aluminum Jack Stands are a pair of lightweight stands made from aircraft-grade aluminum. According to the listing, each stand weighs less than 5 pounds, and the pair offers six adjusting positions between 9.5 and 15.25 inches. The saddle is 2 inches across.

That low starting height is the main reason they make sense for a sixth-generation Camaro, a Malibu or another Chevy car that sits close to the ground. Once a low-profile jack has raised the car a few inches, a stand that begins at 9.5 inches can slip in under the approved support point without lifting the body far higher than the job needs. The narrow saddle also suits reinforced pinch welds better than a wide, flat top does, and you can add a slotted rubber pad if you want to protect the seam.

Aluminum stands are easy to carry to the track or move around a crowded garage, and they do not rust the way bare steel can in a damp Michigan winter. The trade-off is reach. A top setting of 15.25 inches is short for a Silverado or Tahoe frame, so truck owners should look at the taller steel pairs further down this list. Read the stand’s markings and the listing before each use.

View Jackco 3 Ton Aluminum Jack Stands on Amazon

2. OEMTOOLS 24852 3 Ton Jack Stands: 11 to 16-1/2 in. Ratcheting Design

OEMTOOLS 24852 3 Ton Jack Stands product photo
Key features
  • 3 ton capacity, used in pairs
  • 11 to 16-1/2 in. working range
  • Self-locking ratchet adjustment
  • Recessed saddle, welded foot pads

The OEMTOOLS 24852 is a 3 ton steel jack stand sold and used in pairs. The listing gives a working range of 11 to 16-1/2 inches, a self-locking ratchet for lift-and-lock height changes, a recessed saddle that cradles the lift point and large welded foot pads.

This range lines up well with everyday Chevy cars and small crossovers such as a Malibu, Equinox or Trax. An 11 inch starting height still fits under many sedans once the jack has done its work, while the 16-1/2 inch top setting gives a little extra room for a crossover. The recessed saddle helps keep a pinch weld or flat support point centered, which matters when you are pulling on a wheel or a stuck drain plug.

The welded foot pads spread the load over a larger area. OEMTOOLS notes they help the stands resist sinking into asphalt, gravel or soft ground, though solid concrete is still the right surface for any work under a vehicle. These are steel ratchet stands without a listed backup pin, so check that each pawl is fully seated before you go underneath. They are not tall or strong enough for a full-size pickup, which needs one of the heavier pairs below.

View OEMTOOLS 24852 3 Ton Jack Stands on Amazon

captivating aerial view of a snowy forest landscape with a winding river and road

3. Powerbuilt 647511 6 Ton Ratchet Jack Stands: 15-1/2 to 23-1/2 in. Wide Stance

Powerbuilt 647511 6 Ton Jack Stands product photo
Key features
  • 6 ton capacity, sold as a pair
  • 15-1/2 to 23-1/2 in. lift range
  • Ductile iron masts, 10 settings
  • Four-point wide stance, welded seams

The Powerbuilt 647511 is a pair of 6 ton ratchet jack stands with a lift range of 15-1/2 to 23-1/2 inches. The frames are heavy-duty stamped steel with fully welded seams, the ratcheting masts are ductile iron with 10 height settings, and the base uses a four-point wide stance. The listing says they meet or exceed ANSI standards.

That height range is a good match for a Silverado 1500, Tahoe or Colorado. Frame rails on these trucks sit well above the reach of most 3 ton stands, and a top setting of 23-1/2 inches leaves room for a leveled truck or slightly larger tires. With 10 settings spread across the range, it is easier to bring both stands to the same height so the truck sits level.

The wide stance is the other point in its favor. A tall stand carrying a heavy truck needs a broad footprint to stay planted when you lean on a breaker bar, and four legs give it more stability than a narrow three-leg design. The listing does not mention a secondary locking pin, so confirm the pawl is seated on every mast before you trust it. The starting height of 15-1/2 inches is too tall for a Camaro or Malibu.

View Powerbuilt 647511 6 Ton Jack Stands on Amazon

4. Strongway 12 Ton Double-Locking Jack Stands: 24,000 lb Pair with Cast Iron Ratchet

Strongway 12 Ton Jack Stands product photo
Key features
  • 24,000 lb capacity for the pair
  • Double-locking pin plus ratchet
  • Cast iron ratchet drive
  • Listed as conforming to ASME PASE

The Strongway Double-Locking 12-Ton Jack Stands are sold as a pair with a combined rating of 24,000 pounds. The listing describes a heavy-duty reinforced steel frame, a cast iron ratchet drive for precise adjustments, a double-locking pin and a large saddle surface that gives good contact with the load. Strongway states that the stands conform to ASME PASE standards.

This is the class of stand to look at for a Silverado 2500HD or 3500HD, a Suburban or a loaded work truck. Heavy-duty pickups carry far more weight than a half-ton, and a generous rating leaves a margin that a 6 ton pair may not. The pin backup gives a second, visible lock on top of the ratchet, which is reassuring when the truck will sit on the stands while you change brakes or work on the front end.

Large feet spread the load and, according to the listing, help resist sinking into asphalt, which is useful for anyone working in a driveway. The product details do not give a height range, so check the specifications or photos and compare them with your truck’s frame height before ordering. These stands are heavy to move and far more than a car needs.

View Strongway 12 Ton Jack Stands on Amazon

picturesque rural pathway surrounded by fields and clouds under a bright blue sky

5. Sunex 1310 10 Ton Pin Type Jack Stands: Medium Height Pair with Four-Leg Base

Sunex 1310 10 Ton Jack Stands product photo
Key features
  • 10 ton rating, medium height pair
  • Pin-type lock, 6 height adjustments
  • Four-leg steel base, heavy pipe tube
  • Large saddle with locating lugs

The Sunex 1310 is a pair of 10 ton, medium height, pin-type jack stands. The listing describes a four-leg steel base, a support tube made from heavy schedule pipe and multiple holes in that tube for six height adjustments. The height pin is attached to the stand so it does not get lost, and the large saddle has locating lugs to help position a vehicle frame.

Pin-type stands work differently from the ratchet stands above. You lift the tube to the hole you need, then slide a steel pin through, so the load rests on the pin rather than on a pawl and ratchet teeth. Many owners prefer that design for heavy trucks or for a vehicle that will stay up for a longer project, because the lock is simple to see and check.

The saddle lugs help keep a Silverado HD or other framed truck centered on the stand. Adjustment comes in fixed steps rather than fine notches, so you may need a little shim work with the jack to get both sides even. Sunex does not list exact heights in these product details, so check the specification chart before buying. Like the Strongway pair, these are made for trucks rather than cars.

View Sunex 1310 10 Ton Jack Stands on Amazon

Comparing the Five Pairs

Use this table to narrow down the best jack stands for Chevy work, alongside your own floor-to-support measurement. If your number falls near the top of a height range, step up to the next pair rather than running a stand at its last notch.

StandsRated capacityHeight rangeSuits
Jackco 3 Ton Aluminum3 ton (pair)9.5 to 15.25 in.Camaro, Malibu, low cars
OEMTOOLS 248523 ton (pair)11 to 16-1/2 in.Sedans, Equinox, Trax
Powerbuilt 6475116 ton (pair)15-1/2 to 23-1/2 in.Silverado 1500, Tahoe
Strongway 12 Ton24,000 lb (pair)Not stated on listingSilverado HD, Suburban
Sunex 131010 ton (pair)Medium height, 6 settingsHD trucks, longer storage
Ratings and heights as given on each Amazon listing. Check your own vehicle’s weight and support heights before choosing.

Two of the heavier pairs do not list a height range in the product details, so look at the maker’s photos and specification tab before you order. A heavy-duty pickup on a leveling kit can easily need more reach than a stock one.

expansive landscape with clear blue skies and sunlit open field for scenic beauty

Low coupes have their own set of problems, and our jack stands for low cars guide goes deeper on entry height. For more full-size pickup options, see our jack stands for trucks roundup.

A Safe Routine for a Salted Michigan Garage

Whatever pair you choose, the steps stay the same. Work slowly, because a mistake under a Silverado has far less room for forgiveness than a mistake under a compact car.

  1. Flat concrete: set the parking brake, shift to park and chock the wheels staying on the ground.
  2. Approved lift points: jack only where the owner’s manual says, and raise the vehicle in steady strokes.
  3. Stands under solid metal: place them at the approved support points, then lower the jack until the weight settles on both saddles.
  4. Check before you crawl: confirm each lock is fully engaged, fit any backup pin and push firmly on the body before going underneath.

Years of road salt can scale a truck frame and rot the seams around pinch welds. Scrape and inspect the spot before you trust it with the vehicle’s weight. If the metal flakes away or feels soft, move to a sound area and have the corrosion checked.

serene road winds through a verdant valley under a bright summer sun

Stands are only part of a home setup, which also needs a jack, wheel chocks, a torque wrench and a good light. Our list of car maintenance tools for beginners covers the rest of that kit.

Jobs That Belong on a Lift Instead

Stands suit oil changes, tire rotations and quick inspections. Longer jobs, heavy prying on suspension parts and anything that shifts the vehicle’s balance are safer with the car or truck on a proper two-post lift.

beautiful lush green hills and winding road

Our factory scheduled maintenance service in Grand Rapids follows the schedule in your Chevy’s maintenance guide with the vehicle on a lift. If you spot worn pads or a grinding noise while you are under there, our brake repair team can take a closer look.

Frequently Asked Questions

What are the best jack stands for a 6th gen Camaro 1LE?

Short stands with a low starting height suit the car, since it sits close to the ground. The Jackco aluminum pair starts at 9.5 inches and the OEMTOOLS 24852 at 11 inches. Place them only at the support points shown in your owner’s manual.

Are 3 ton stands enough for a Silverado 1500?

They can be rated high enough, but many 3 ton stands top out around 16 to 17 inches, which can be short for a pickup frame. A 6 ton pair such as the Powerbuilt 647511 reaches 23-1/2 inches and gives more capacity margin.

Where do jack stands go on a Chevy truck?

On most Silverado, Tahoe and Suburban models the stands go under the frame rails or axle at the points your owner’s manual approves. Avoid suspension arms, the body, running boards and skid plates.

Should I choose ratchet or pin-type stands?

Ratchet stands are faster to set, and double-locking versions add a pin for backup. Pin-type stands like the Sunex 1310 adjust in fixed steps but lock with steel through the column, which some owners prefer for long jobs.

Would you rather leave the lifting to us? Call 456 AutoFix on 616-279-3832 between 8am and 5pm, Monday to Friday, or send a request through our contact page to set up a time.

Busy during shop hours? Leave your Chevy with our after-hours drop-off at 456 Carrier St NE in Grand Rapids.