456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Brighter Pickups After Dark: Best LED Headlight Bulbs for Trucks

best led headlight bulbs for trucks: quiet rural road stretches into the distance

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A pickup’s factory halogens can feel weak on an unlit two-lane road with slush on the shoulder. Choosing the best LED headlight bulbs for trucks starts with the socket, not the lumen number: the bulb has to match your truck’s size and beam layout, fit behind the housing and still throw a clean cutoff once it’s aimed.

Below: how trucks lay out their bulbs, the legal side of plug-in LEDs and six sets in common pickup sizes. For housings and color temperature, see our main guide to LED headlight bulbs for every vehicle.

Quick answer

Which LED headlight bulbs suit a truck?

Match the size first. Trucks with separate H11 low and 9005 high beams can use a four-bulb combo such as the fanless Marsauto M1S, while dual-beam trucks need one bulb per side, like the BEAMTECH H13 or AUXITO H4. Re-aim after fitting, and know that plug-in LEDs in halogen housings aren’t DOT-approved.

Our Quick Picks

Three sets that cover the common truck layouts: a fanless four-bulb combo for H11 and 9005 trucks, a fan-cooled H13 pair and a dual-beam H4 pair. All six sets are reviewed below.

Marsauto M1S 9005 + H11 product photo
Fanless combo

Marsauto M1S 9005 + H11

9005 + H11 · 4 bulbs · 6000K

A silent four-bulb set for split-beam trucks with tight housings.

SuitsShallow housings and drivers who dislike fan noise
View on Amazon →
BEAMTECH H13 product photo
Dual-beam H13

BEAMTECH H13

H13/9008 · pair · 6500K

A fan-cooled dual-beam pair for trucks with one bulb per side.

SuitsH13 trucks with room behind the housing
View on Amazon →
AUXITO H4 product photo
Dual-beam H4

AUXITO H4

H4/9003 · pair · 6500K

A high/low pair for trucks with H4 headlamps.

SuitsOlder trucks and heavy rigs with H4 lamps
View on Amazon →

Split Beams or One Bulb per Side: How Trucks Wire Their Headlights

Pickups tend to follow one of two layouts. In the first, each headlight holds two bulbs: one for low beam and one for high beam. An H11 low beam paired with a 9005 (HB3) high beam is a common pairing, which is why so many LED kits are sold as four-bulb combos.

The second layout uses a single dual-filament bulb per side that handles both beams. H13 (9008), 9007 (HB5) and H4 (9003) are the usual sizes here, and they are found on many older pickups and heavier trucks. An LED replacement for these sockets has to switch between two light patterns inside one bulb, so beam control matters even more.

Read the size on the base of the old bulb or in your owner’s manual. Confirm year, model, trim and bulb position in Amazon’s part finder too, because one truck can use different sizes across trims.

Are LED Headlight Bulbs Legal on a Truck?

This is the question most listings skip. Sylvania’s own automotive bulb FAQ states that current federal law prohibits replacing halogen lamps with LEDs for low and high beam headlight use, and the company supports its LED bulbs only for fog lights. US headlamps are certified as a complete system, so a plug-in LED in a housing built for halogen isn’t a DOT-approved combination, whatever a box claims.

That’s why many of the listings below mention fog lights, off-road use or powersports in their titles. If your truck came with factory LED headlamps, the bulbs aren’t replaceable this way anyway. For an on-road upgrade that stays compliant, a DOT-marked LED headlamp assembly or a premium halogen bulb is the conservative route.

If you do fit plug-in LEDs, glare is the real risk. Sylvania blames poor aim, hazy lenses and non-compliant upgrades, and a truck’s tall front end already puts its beams near car drivers’ eyes.

Best LED Headlight Bulbs for Trucks: Six Sets by Socket

The six sets below cover the split-beam H11 and 9005 sizes first, then the dual-beam H13, 9007 and H4 sockets. Specs come from each Amazon listing, and lumen totals are the makers’ own claims.

1. AUXITO H11 9005 LED Combo: 4 Bulbs, 6500K with Dual Copper Cooling Tubes

AUXITO H11 + 9005 Combo product photo
Key features
  • Four bulbs: H11 pair plus 9005 pair
  • 6500K white light
  • Dual copper cooling tubes, IP68 rating
  • 1:1 fit, no polarity, CANbus-friendly

The AUXITO combo packs four bulbs in one box: a pair of H11 bulbs and a pair of 9005 bulbs. That suits the many pickups that run an H11 low beam beside a 9005 high beam, since you can change both positions on each side at once and get a matching color. AUXITO lists the set at 240,000 lumens in total with a 6500K white color, and like most Amazon lumen figures, that number is the maker’s own claim.

Cooling uses dual copper tubes inside an aluminum body, and the listing gives an IP68 rating against rain and dust, which matters behind a bumper that collects slush all winter. AUXITO describes a 1:1 fit with factory housings, no polarity to worry about and a five minute install. It also says the bulbs work with most vehicles out of the box, with a decoder kit for the occasional model that flickers or shows an error.

This set suits a split-beam truck where you want one purchase instead of two. Check that your low beam really is H11 and your high beam really is 9005, since some trims swap in other sizes. The listing also leans on fog and off-road use, so read the legality section above and aim the low beams carefully after fitting.

View AUXITO H11 + 9005 Combo on Amazon

2. SEALIGHT 9005/HB3 LED Bulbs: 6500K CSP Chips, IP68, Pack of 2

SEALIGHT 9005 product photo
Key features
  • 9005/HB3 base, pair
  • CSP chips placed at the filament position
  • All-in-one body, no separate driver
  • CANbus-ready built-in IC driver

The SEALIGHT 9005 pair is for trucks that only need to change one position, most often a 9005 high beam. SEALIGHT lists 70,000 lumens for the pair at 6500K, using CSP chips that it says mimic the position of the original halogen filament. Keeping the light source in that spot is what lets the housing shape the beam without dark patches or shadows.

The bulb uses an all-in-one design, so there is no separate driver box or extra harness to tuck away behind the headlight. It is non-polarity, so the plug works either way round, and SEALIGHT puts the install at about three minutes. An aviation aluminum body handles cooling, the IP68 rating covers rain and snow, and the maker quotes a lifespan of over 70,000 hours.

SEALIGHT says the built-in IC driver is CANbus ready and works with most vehicles, but it also warns that Amazon’s fitment filter is not always accurate. Check your owner’s manual or the old bulb’s base before ordering. This pair suits a truck that already has good low beams and needs a whiter high beam, or a truck whose low beam happens to use 9005. Re-aim after fitting either way.

View SEALIGHT 9005 on Amazon

vibrant light trails create a dynamic urban scene on a bustling highway at night

3. Marsauto M1S 9005 + H11 Fanless LED Bulbs: 6000K, 4-Pack

Marsauto M1S 9005 + H11 product photo
Key features
  • Four bulbs: 9005 pair plus H11 pair
  • Fanless, passive cooling
  • 6000K cool white
  • IP68 shell, built-in CANbus

The Marsauto M1S is another four-bulb combo for 9005 and H11 sockets, but it drops the cooling fan entirely. Passive cooling through an IP68-rated 6063 aluminum shell means no moving parts and no fan whine at idle. Marsauto lists 6000K cool white light, a little warmer than the 6500K sets here, which some drivers find easier on the eyes in snow.

The listing describes a 1:1 halogen size with no brackets, adapters or modifications, and a twist-and-lock install that takes under three minutes. Marsauto says an ultra-thin board produces a halogen-like beam pattern with no dark spots and less glare for oncoming traffic. Built-in CANbus circuitry is meant to prevent dashboard warnings and flicker without coding or resistors, and the maker quotes more than 80,000 hours of life.

This set suits a split-beam truck with limited space behind the headlights, where a fan-cooled bulb could stop the dust cap from closing. Because the bulbs are fanless, keep them away from enclosed housings that trap heat, and check that the light switches on cleanly after a cold night. The listing mentions fog lights and ATVs as well, so aim the low beams with care before regular road use.

View Marsauto M1S 9005 + H11 on Amazon

4. BEAMTECH H13/9008 LED Bulbs: 6500K with 15,000 RPM Turbo Fan, Pack of 2

BEAMTECH H13 product photo
Key features
  • H13/9008 dual-beam base, pair
  • 15,000 RPM fan and liquid cooling tube
  • 7035 LED chips, 6500K
  • CANbus ready, five minute install

The BEAMTECH H13 pair covers a socket found on plenty of pickups and work trucks, where a single 9008 bulb provides both the high and low beam. BEAMTECH says its 7035 chips give 800 percent more light than the old bulbs while using about half the energy, with a 6500K white color. Treat the brightness figure as a maker claim and judge the bulb by its cutoff on a wall.

Cooling is the most elaborate in this guide: a 15,000 RPM turbo fan, a liquid cooling tube and an aviation aluminum body, which BEAMTECH links to a 50,000 hour lifespan. The maker describes a direct replacement that takes less than five minutes, and the listing says the bulbs are CANbus ready for nearly all vehicles. BEAMTECH also notes circuit board, assembly and aging tests in production.

This pair suits an H13 truck with enough depth behind the housing for the fan and its cooling hardware, so measure before ordering. Because each bulb handles two beams, flip between high and low after fitting and confirm both patterns look right. H13 and H4 bases look alike at a glance but are not interchangeable, so read the code on your old bulb first.

View BEAMTECH H13 on Amazon

silhouetted cars driving on a road at sunset with streetlights and power lines

5. Termitor 9007/HB5 LED Bulbs: 6500K, 36 Chips with Cooling Fan, Pack of 2

Termitor 9007 product photo
Key features
  • 9007/HB5 dual-beam base, pair
  • 36 chips per bulb, 6500K
  • High-speed fan, aluminum housing
  • CANbus driver, 1:1 mini size

The Termitor 9007 pair is built for the HB5 socket, a dual-beam size used on many older pickups and SUVs. Each bulb carries 36 chips, and Termitor lists 110,000 lumens for the pair at 6500K cool white. In a 9007 headlamp one bulb produces both high and low beam, so the quality of the low beam cutoff counts for more than the headline number.

Termitor describes a focused beam with distinct boundaries, meant to light the road without dazzling oncoming drivers when installed properly. The bulb uses a true 1:1 mini design, so no adapters or modifications are needed, and the maker puts the install at under three minutes. A high-speed cooling fan and aviation-grade aluminum housing carry heat away, and Termitor quotes a service life of over 90,000 hours.

The listing says its CANbus drivers suit more than 95 percent of vehicles and recommends checking the bulb size against your manual or original part number. This pair suits a truck whose headlights take one 9007 bulb per side and have room for a small fan. The title also mentions fog and off-road use, so keep the legality note in mind and check both beams against a wall after fitting.

View Termitor 9007 on Amazon

6. AUXITO H4/HB2/9003 LED Bulbs: 6500K Dual Beam, IP68, 2 Pack

AUXITO H4 product photo
Key features
  • H4/HB2/9003 dual-beam base, pair
  • Chips 1.2mm apart to copy the filament
  • Aluminum body, copper base board
  • Non-polarity, EMC protection, IP68

The AUXITO H4 pair fits the H4, HB2 and 9003 socket, a dual-beam size common on older trucks and on some heavy trucks with replaceable bulbs. AUXITO lists 84,000 lumens for the pair at 6500K. The detail that matters more is the chip layout: dual-sided chips sit 1.2mm apart to mimic where the halogen filament sat, which helps the housing form a cleaner beam with fewer dark zones.

Heat management comes from a full aluminum body and a copper base board, which AUXITO links to a 60,000 hour lifespan. The connector is non-polarity and plug-and-play, with no modifications needed for an H4 socket. The listing also mentions EMC protection to reduce electrical interference, useful in a cab with a CB or other radio, and an IP68 rating against rain, snow and dust.

This pair suits a truck with H4 headlamps whose owner wants a whiter beam without replacing the housing. Before ordering, confirm the base, since H4 and H13 bulbs look similar but will not swap. After fitting, check both beams on a wall, because an H4 bulb seated slightly off in its socket can throw light upward. For a commercial rig, read the semi truck section first.

View AUXITO H4 on Amazon

Matching a Bulb Set to Your Truck

Find your row by the old bulb’s size, then weigh space and noise. Fan-cooled bulbs need room behind the housing so the dust cap seals, while fanless ones run silently. Trucks that tow also gain from a tight cutoff.

Your truck’s socketsBeam layoutSets in this guideCheck before buying
H11 low + 9005 highTwo bulbs per sideAUXITO combo, Marsauto M1S, SEALIGHT 9005Whether the combo covers both positions
H13 (9008)One bulb, high and lowBEAMTECH H13Fan depth behind the housing
9007 (HB5)One bulb, high and lowTermitor 9007Dust cap clearance
H4 (9003)One bulb, high and lowAUXITO H4H4 and H13 bases are not interchangeable
Best LED headlight bulbs for trucks matched to socket size and beam layout
beautiful sunset illuminates a rural farm with vibrant colors and a winding path

Best LED Headlight Bulbs for Semi Trucks and Heavy Rigs

Heavy trucks use a wide mix of headlamps. Some take replaceable H4, H13 or 9007 bulbs, others use sealed-beam units or complete LED headlamp assemblies, and the right part depends on the exact cab and model year. Start with the part number on the old bulb or headlamp, not a general listing.

The legal point carries extra weight on a rig that runs all night: a plug-in LED in a halogen housing isn’t a DOT-approved headlamp. Fleet drivers should check company policy first, and owner-operators usually do better with a DOT-marked assembly made for that truck.

empty asphalt roadway near growing trees and bright lamp posts under sky in town in darkness

Aim, Salt and Wiring After the Swap

Re-aim the headlights after any bulb change, and again after a lift or leveling kit, because raising the front end tips the beam upward. Park on level ground facing a wall, compare both cutoffs and adjust the housings until they sit level and below oncoming drivers’ eye height.

West Michigan winters are hard on anything behind the grille. Brine and slush find their way into a dust cap that won’t close over a bulky fan, so check the cap seals fully before you finish. A thin film of dielectric grease for electrical connectors on the plug seal helps keep salt water away from the terminals.

peaceful rural scene with a tree and path silhouetted against a vibrant sunset

Flicker that a CANbus-ready bulb doesn’t cure, or a headlight fuse that pops again after replacement, points to a wiring fault rather than a bad bulb. Our guide on why a car fuse keeps blowing covers the usual suspects. If the battery is flat after the truck sits for a few days, read why a car battery dies overnight, and if the cause stays hidden, our car electrical repair in Grand Rapids traces the circuit, relay and switch.

Frequently Asked Questions

How do I find the headlight bulb size for my truck?

Read the code printed on the base of the old bulb, or look up the bulb chart in your owner’s manual. Many trucks use different sizes for low beam, high beam and fog lights, so check each position, and confirm year, model and trim in Amazon’s part finder before ordering.

What are the best LED headlight bulbs for semi trucks?

It depends on the headlamp. Some heavy trucks take H4, H13 or 9007 bulbs, while others use sealed beams or full LED assemblies. Because plug-in LEDs in halogen housings are not DOT-approved, a DOT-marked replacement assembly made for the truck is usually the safer choice for a rig on the highway.

Do LED truck headlights need a CANbus decoder?

Some trucks monitor bulb current and show a warning or make LEDs flicker. Most of the sets here list a CANbus-ready driver, which handles it on many vehicles, but a separate decoder harness can still be needed. Flicker that continues after that deserves a wiring check.

Should I re-aim my headlights after a lift kit?

Yes. Raising the front of a truck tilts the beam upward, and brighter LED bulbs make that glare worse for other drivers. Check the cutoff against a wall on level ground and lower the housings until both beams sit level.

Swapped the bulbs and the beams still flicker, dim or blow fuses? Give Hendrick’s team a call at 616-279-3832, Monday through Friday from 8am to 5pm, or use our contact page to describe what the lights are doing.

You’ll find 456 AutoFix at 456 Carrier St NE in Grand Rapids. If your work hours overlap ours, the after-hours drop-off lets you leave the truck whenever it suits you.