456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Same Honda, Two Brands: Bosch vs Denso Oxygen Sensor Compared

bosch vs denso oxygen sensor: close-up of an elderly scientist using paper filters in a chemistry experiment with glass apparatus

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

Ask ten people about a bosch vs denso oxygen sensor and you will hear ten loyal answers, most of them about some other car. Brand loyalty matters less than one simple test: does the part number cross to the sensor your engine left the factory with, in the exact position that set the code?

To keep this fair, we put one Bosch and one Denso part on the same vehicle and the same spot: the upstream air-fuel sensor on a 2007-2009 Honda CR-V with the 2.4-liter four-cylinder. Every figure comes from the Amazon US listings. If you drive something else, our guide to choosing an oxygen sensor brand covers Walker, Delphi, ACDelco and Motorcraft as well.

Quick answer

Should a 2007-2009 CR-V get the Bosch or the Denso upstream sensor?

Both are direct-fit wide-band sensors for the 2.4L engine. Choose the Denso 234-9062 if you want a part that lists Honda’s own RZA numbers and its measuring range. Choose the Bosch 15286 for its sealed stainless body and threads pre-coated with anti-seize. If the code names sensor 2, you need the NTK 24266 instead.

Our Quick Picks

One Bosch and one Denso upstream sensor for the same 2007-2009 CR-V 2.4L, plus the NTK rear sensor for that engine, all reviewed below.

Denso 234-9062 product photo
Honda number match

Denso 234-9062

Upstream A/F sensor, 4-wire, 2007-2009 CR-V

Lists Honda's own RZA part numbers and its measuring range.

SuitsOwners who want a direct cross to the Honda part
View on Amazon →
Bosch 15286 product photo
Ready-to-install pick

Bosch 15286

Upstream wideband, OE connector, 2007-2009 CR-V

Sealed stainless body and anti-seize already on the threads.

SuitsDIY installs on salt-belt cars
View on Amazon →
NTK 24266 product photo
Rear sensor pick

NTK 24266

Downstream sensor 2, direct fit, CR-V 2.4L

The after-converter sensor for the same engine as the front picks.

SuitsSensor 2 heater or signal codes
View on Amazon →

What the Front Sensor Does on This Honda

The CR-V has two oxygen sensors on its single exhaust bank. Sensor 1 sits ahead of the catalytic converter and tells the engine computer how rich or lean the mixture is, so it can trim fuel many times a second. Sensor 2 sits after the converter and mainly reports whether the converter is still storing oxygen and cleaning up the exhaust.

On this engine, sensor 1 is an air-fuel ratio sensor, often called a wide-band sensor. A conventional sensor only flips between a rich signal and a lean signal, while an air-fuel sensor reports how far from the ideal mixture the engine is running. That is why the two front sensors cost more than the rear one and why a universal splice-in part is a poor idea here.

A failing front sensor usually shows up as a check-engine light, worse fuel economy or a hesitation that comes and goes. Our article on bad oxygen sensor symptoms walks through the signs in more detail. Read the stored code before you order anything, since the code tells you which sensor the computer is unhappy with.

Three Part Numbers Side by Side

The table lists what each Amazon listing states. Where a listing says nothing about a point, the cell says so rather than filling it with a guess.

PointBosch 15286Denso 234-9062NTK 24266
Position on the 2007-2009 CR-V 2.4LUpstream, sensor 1Upstream, sensor 1Downstream, sensor 2
Sensor typeWide-bandWide-band air-fuel ratioOxygen sensor
Honda numbers it replacesNot listed in the bullets36531-RZA-003, 36531-RZA-01336532-RZA-004, 36532-RZA-014
Build details statedDouble laser-welded stainless body, fast heaterPlatinum electrodes, planar zirconia elementGenuine NGK NTK part, direct replacement
Install extrasOE connector, threads pre-coated with anti-seize4-wire, 11.38-inch harnessOriginal packaging and hardware
Other vehicles listed2013-2015 Acura ILXNone beyond the CR-VConfirm with Amazon’s fit checker
Bosch vs Denso oxygen sensor for the 2007-2009 Honda CR-V, with the NTK rear sensor for the same engine

The Denso listing even names Bosch 15286 and NTK 24835 in its interchange list, which confirms the two front sensors are meant for the same job. The choice comes down to the build details and the extras in the box, not to which one fits.

Bosch vs Denso Oxygen Sensor Picks Reviewed

The 2010 and 2011 CR-V use a different front sensor, so none of these is a match for those years. Confirm your year, model and engine with Amazon’s fit checker before you order, and match the position to the code.

Denso 234-9062: Wide-Band Air-Fuel Ratio Sensor for 2007-2009 Honda CR-V

Denso 234-9062 product photo
Key features
  • Upstream sensor 1 for the 2007-2009 CR-V
  • Replaces Honda 36531-RZA-003 and -013
  • Platinum electrodes, planar zirconia element
  • 4-wire plug on an 11.38-inch harness

The Denso 234-9062 is a wide-band air-fuel ratio sensor listed for the 2007-2009 Honda CR-V. It mounts upstream of the catalytic converter in the sensor 1 position, where the engine computer reads it to set fuel trim. The listing names Honda part numbers 36531-RZA-003 and 36531-RZA-013 in its interchange, along with Bosch 15286 and NTK 24835, so you can match it against the number on the old sensor before ordering.

Denso describes a planar zirconia element built to detect oxygen concentration quickly and platinum electrodes that resist tarnish, which helps the sensor keep its accuracy over time. The listing states a measuring range of roughly 12:1 to 19:1 air-fuel ratio, which covers the rich and lean swings a healthy engine makes in normal driving. The sensor arrives with a 4-wire harness 11.38 inches long ending in a factory-style plug, so no splicing is needed.

This part suits CR-V owners who like a replacement that lines up directly with the Honda numbers. The listing does not mention anti-seize on the threads, so check them and add a small amount of sensor-safe compound if they are bare. It does not fit the 2010 or 2011 CR-V, and it is not a rear sensor, so a sensor 2 code needs a different part.

View Denso 234-9062 on Amazon

solitary asphalt road stretches across the arid Californian desert

Bosch 15286: OE Fitment Wideband Oxygen Sensor for Honda CR-V and Acura ILX

Bosch 15286 product photo
Key features
  • Upstream wideband for 2007-2009 CR-V
  • Also listed for 2013-2015 Acura ILX
  • Double laser-welded stainless steel body
  • OE connector, threads pre-coated with anti-seize

The Bosch 15286 is a wideband oxygen sensor from Bosch’s OE Fitment line, listed for the 2007-2009 Honda CR-V and the 2013-2015 Acura ILX. On the CR-V it takes the same upstream sensor 1 position as the Denso 234-9062, ahead of the catalytic converter. Bosch notes that it has built oxygen sensors since it first developed them in the late 1960s, and this part draws on that long production history.

The listing highlights a stainless steel body that is double laser-welded and sealed, which protects the internals from water and exhaust contamination. A fast-acting heater brings the sensor up to working temperature within seconds, so the engine computer can begin closed-loop fuel control sooner after a cold start. The sensor uses a direct-fit OE connector and harness, and the threads come pre-coated with anti-seize compound, which saves a step during installation.

This sensor suits owners doing the job at home, particularly on cars that see road salt, because the pre-coated threads make the next removal easier. The listing gives no measuring range and does not print the Honda part numbers in its bullets, so use Amazon’s fit checker with your year and engine. Like the Denso, it is a front sensor only and is not listed for the 2010-2011 CR-V.

View Bosch 15286 on Amazon

NTK 24266: Direct-Fit Downstream Oxygen Sensor with OE Connector

NTK 24266 product photo
Key features
  • Replaces Honda 36532-RZA-004 and -014
  • Crosses to Denso 234-4359 and Bosch 15318
  • Genuine NGK NTK part
  • Ships with original packaging and hardware

The NTK 24266 is the downstream partner to the two front sensors above. Its listing shows it replacing Honda numbers 36532-RZA-004 and 36532-RZA-014, along with Denso 234-4359 and Bosch 15318, the rear sensor numbers used on the 2007-2009 CR-V 2.4L. It threads into the exhaust after the catalytic converter in the sensor 2 position, where it mainly reports how well the converter is working.

NTK is the sensor brand of NGK, the spark plug maker, and the listing states this is a genuine NGK NTK part sold as a direct replacement. It comes in the original packaging with its hardware, and it plugs into the factory connector without any cutting or splicing. Because the rear sensor does a narrower job than the air-fuel sensor up front, it costs less to replace, and it is the part to reach for when the code points to sensor 2.

The listing itself gives few product details and asks buyers to confirm fitment with Amazon’s fit checker, so enter your year, model and engine before ordering. Do not use it to answer a catalyst efficiency code on its own, since a tired converter, a leak or a misfire can set that code with a healthy sensor. It is not a substitute for either front sensor.

View NTK 24266 on Amazon

set of colorful Allen wrenches organized from small to large on a dark background

Where the Two Brands Really Differ

Factory ties

Denso is a long-standing supplier to Japanese automakers, and its aftermarket site describes its range as OE compatible oxygen and air-fuel ratio sensors. On this CR-V, the Denso listing ties its part directly to Honda’s RZA part numbers. Many owners of Japanese cars like that link, because it removes any doubt about the plug, the harness length and the signal the computer expects.

Bosch comes at it from the other side. Its listing points out that Bosch has built oxygen sensors since it first developed them in the late 1960s, and the Bosch oxygen sensor catalog covers a very wide spread of domestic, European and Asian vehicles. A Bosch part that lists your car is engineered for it, even when the original sensor came from another maker.

Construction and the box contents

Bosch spells out its housing: a stainless steel body that is double laser-welded and sealed. Denso spells out the inside instead, with platinum electrodes and a planar zirconia element built for quick response. Neither claim makes the other part worse, they simply describe different things.

weathered speed limit sign on a deserted highway with a clear sky background

The practical difference is the anti-seize. Bosch pre-coats the threads, while the Denso bullets do not mention it, so check the threads when the box arrives. If they are bare, use only a small amount of sensor-safe anti-seize on the threads and keep it well away from the tip, since contamination can upset the reading.

Matching the Part to the Code

Start with the code and the position, then pick a brand. The generic codes below are a guide only, since Honda also uses its own codes for the air-fuel sensor.

What you seeLikely positionPart to consider
P0135, heater circuit bank 1 sensor 1UpstreamBosch 15286 or Denso 234-9062
Air-fuel sensor slow or out of range, poor mileageUpstreamBosch 15286 or Denso 234-9062
P0141, heater circuit bank 1 sensor 2DownstreamNTK 24266
P0420, catalyst efficiencyConverter or rear sensorDiagnose first, do not guess
Common 2007-2009 CR-V oxygen sensor codes and where they point

A heater circuit code can also come from a blown fuse, a chafed wire or a corroded connector, so a quick look at the plug is worth doing before you spend money. A catalyst code is the one most often misread as a sensor fault. Our page on a check engine light when the car runs fine explains why a code is a starting point rather than a verdict.

vibrant set of colorful Allen wrenches neatly arranged on a dark surface

West Michigan winters add one more step. Years of road salt can weld a sensor into its bung, and a stripped thread turns a half-hour job into exhaust work. Soak the threads with penetrating oil, work the sensor with the engine slightly warm, and use a proper slotted socket from our O2 sensor socket guide so the wiring is not crushed.

Also look for an exhaust leak ahead of the front sensor. Outside air pulled in through a cracked flange or a loose joint makes a good sensor report a lean mixture, and a new sensor will not fix that. A small leak can sometimes be sealed with a product from our exhaust repair kit roundup, but anything near the manifold usually needs a proper repair.

When a Shop Visit Saves Money

Replacing a sensor that was never bad is the most common way to waste money on this job. If the code returns after a new sensor, or a catalyst code sits alongside a sensor code, the fault is usually elsewhere: a leak, a wiring problem, a misfire or a tired converter. Settling the bosch vs denso oxygen sensor question only helps once you know the sensor is really at fault.

long road stretches through a barren desert

Our team handles check engine light diagnostics in Grand Rapids and reads live sensor data before we recommend a part. If the sensor is seized, the threads are damaged or the system is leaking, our exhaust repair service in Grand Rapids can repair the pipe and fit the new sensor properly.

Frequently Asked Questions

Is Bosch or Denso better for a Honda oxygen sensor?

Either is a sound choice when the part number lists your exact year and engine. On a 2007-2009 CR-V 2.4L, the Denso 234-9062 lists Honda’s RZA numbers directly, and the Bosch 15286 lists the same vehicle with pre-coated threads and a stainless body.

Do these sensors fit a 2010 or 2011 CR-V?

No. The 2010 and 2011 models use a different upstream sensor. Enter your year, model and engine in Amazon’s fit checker and match the position to the code before you order.

Should I replace both oxygen sensors at once?

Not automatically. Replace the sensor the code points to. If the car has high mileage and the other sensor is original, doing both while the car is in the air can make sense, but it is a choice rather than a rule.

Will a new oxygen sensor turn off the check-engine light?

Only if the sensor was the cause. Clear the code after the repair and drive normally for a few days. If the light returns with the same code, look for wiring trouble, an exhaust leak or a converter problem.

Not sure which sensor your code is pointing at? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or ask for a sensor check through our contact page.

Short on daytime hours? Our after-hours drop-off is open at 456 Carrier St NE, Grand Rapids, so the CR-V can wait for us overnight.