As an Amazon Associate, 456 AutoFix earns from qualifying purchases. The product links below open the Amazon listing, where you can confirm the bottle size before you order.
Threadlocker vs anti seize sounds like a choice between two similar tubes of goop, but the two compounds do opposite jobs. One makes a bolt harder to turn so vibration cannot back it out. The other makes a bolt easier to turn years from now, after heat and road salt have done their worst.
Picking the wrong one can leave you with a caliper bracket bolt that walks loose or an exhaust stud that snaps on removal. This guide explains what each product is made for, which car jobs suit each, how they affect torque, and three products worth keeping on the bench.
Quick answer
Should a bolt get threadlocker or anti-seize?
Use blue threadlocker on fasteners that vibration could loosen and that stay fairly cool, such as valve cover or water pump bolts. Use anti-seize on hot or rust-prone threads you will remove again, like exhaust studs and spark plugs. Pick one per thread, and follow the vehicle maker’s torque figure.
Our Quick Picks
One blue threadlocker, one brush-top anti-seize, and an oil-tolerant threadlocker as a related third pick for hardware you cannot fully degrease.

Permatex 24200 Blue Threadlocker
A small bottle of blue threadlocker for bolts that vibration could loosen.

Permatex 80071 Anti-Seize
A brush-top bottle of anti-seize for threads you want to remove cleanly later.

Loctite 243 Blue Threadlocker
A larger blue threadlocker that tolerates a light oil film on the threads.
Two Compounds With Opposite Goals
A threadlocker is a liquid adhesive that hardens in the gaps between mating threads once air is shut out. According to Loctite’s guide to red and blue threadlocker, these products are mainly designed to stop fasteners from leaking or loosening under vibration. Blue grades come apart with ordinary hand tools, while the red grade is meant to be more permanent.
Anti-seize is a grease loaded with fine metal or graphite particles. It does not cure or bond. Instead, it sits between the threads as a barrier that keeps rust, heat scale and galling from fusing the bolt to the hole, so the part can come out cleanly at the next service.
Put simply, threadlocker adds holding power and anti-seize removes friction. That is why they rarely belong on the same fastener, and why a mechanic reaching for one usually has a clear reason not to use the other.
Threadlocker vs Anti Seize Side by Side
The table matches each compound to jobs that come up on a typical car or light truck. It is general guidance, so the service information for your vehicle has the final word on any specific bolt.
| Question or job | Blue threadlocker | Anti-seize |
|---|---|---|
| Main purpose | Stops loosening from vibration | Stops seizing, galling and rust lock |
| How it works | Cures into a solid between threads | Stays a paste with lubricating particles |
| Valve cover, oil pan, water pump bolts | Common choice | Not usually needed |
| Exhaust studs and manifold nuts | Heat works against it | Common choice |
| Spark plug threads | Not used | Only if the plug maker allows it |
| Removal later | Hand tools for blue grades | Easier than a dry thread |
The table leaves out a third answer that comes up often: plenty of bolts get neither compound. Many fasteners are designed to be installed clean and dry, and the torque figure assumes exactly that.
Threadlocker vs Anti Seize: Three Products Reviewed
The first two picks represent each side of the comparison, and the third is an oil-tolerant threadlocker for hardware you cannot get perfectly clean. Check the listing for the size you need before ordering.
Permatex 24200 Blue Threadlocker: 6 ml Medium Strength, Removable with Hand Tools

- Medium strength, removable with hand tools
- Resists loosening from shock and vibration
- Sized for 1/4 to 3/4 inch fasteners
- Helps protect threads from corrosion
This small bottle is the threadlocker side of the comparison. Permatex lists it as a medium strength blue formula that locks nuts and bolts against loosening from shock and vibration, while still allowing removal with ordinary hand tools. That removability is the reason blue is the usual grade for parts on a car that will need service again.
The listing sizes it for fasteners from 1/4 to 3/4 inch, or 6 to 20 mm, and says it can replace lock nuts and lock washers on many jobs. It also seals the threads, which helps keep out moisture and corrosion. Suggested uses include valve cover bolts, water pump bolts, oil pan bolts, drive shaft bolts, rocker arm adjustment nuts, carburetor studs and intake manifold bolts.
In practice, clean the threads, apply a few drops where the nut engages, and tighten to the vehicle maker’s figure. The 6 ml size suits a home garage, since a little goes a long way and a big bottle can age before you finish it. It is not the product for hot exhaust hardware, spark plugs or anything you want to stay easy to turn. Keep it on parts that shake loose, and pair it with the threadlocker strength guide if you need a different grade.
View Permatex 24200 Blue Threadlocker on Amazon

Permatex 80071 Anti-Seize Lubricant: 4 oz Brush Top Bottle, Rated -60F to 1600F

- Blend of aluminum, copper and graphite
- Rated from -60F to 1600F
- Resists salt, corrosion and moisture
- Brush top bottle for thin coats
This bottle covers the anti-seize side. Permatex describes the compound as a highly refined blend of aluminum, copper and graphite lubricants, with a listed temperature range of -60F to 1600F. Those solid particles stay between the threads after assembly, so rust and heat scale have a harder time locking the fastener in place.
The listing says the lubricant resists salt, corrosion and moisture, and that it prevents galling, corrosion and seizing to make disassembly easier. Its suggested applications are spark plugs, cylinder head bolts and exhaust head bolts, which are the hot, hard-to-reach threads that tend to fight back at removal time. The maker also calls it ideal for marine use, which fits the salt and moisture resistance it claims.
The brush built into the cap makes a thin, even coat easy and keeps fingers out of the paste. Apply a light film, keep it off sensor tips, and wipe away the extra. Check the spark plug maker’s instructions first, because some plugs are not meant to have anti-seize. It also changes how torque translates into clamping force, so follow the vehicle maker’s guidance, and keep it well away from brake pads, rotor faces or anything that relies on friction.
View Permatex 80071 Anti-Seize on Amazon
Loctite 243 Blue Threadlocker: 50 ml Medium Strength with Improved Oil Tolerance

- General-purpose medium strength blue
- Improved oil tolerance
- Cures on as-received fasteners
- 50 ml bottle for frequent use
The third pick is a related option rather than a third compound type. Loctite 243 is a general-purpose, medium strength blue threadlocker, so it does the same holding job as the Permatex bottle above. What sets it apart, according to the listing, is improved oil tolerance.
Loctite says it cures on as-received fasteners without cleaning, which matters in an engine bay where threads often carry a light film of oil. Threadlockers cure once air is shut out between metal threads, and contamination can weaken that cure. A formula built to cope with some oil gives a little more margin when a bolt hole cannot be fully degreased. Like other blue grades, it is meant to be removable rather than permanent.
The 50 ml bottle suits someone who uses threadlocker often, such as a weekend mechanic working through a project car or a fleet of family vehicles. Cleaning the threads is still good practice, and the vehicle maker’s torque figure still applies. It does not replace anti-seize on hot exhaust hardware, and it is not a fix for stripped threads. If you want a smaller bottle or a single-job amount, the Permatex 24200 above is the simpler choice.
View Loctite 243 Blue Threadlocker on Amazon

Anti Seize vs Threadlocker on One Bolt, and What It Does to Torque
Stacking both compounds on the same threads defeats the purpose of each. The grease in anti-seize keeps a threadlocker from contacting clean metal, so it may not cure properly, and the lubricating film still lets the bolt turn more easily. If a joint truly needs both properties, the vehicle maker’s procedure will say so and spell out where each product goes.
Torque is the part people miss. A torque figure is written for a stated thread condition, often clean and dry. Coat those threads with anti-seize and the same wrench reading can stretch the bolt further, which risks stripped aluminum threads or a fastener that yields.

Follow the vehicle maker’s instructions: some list a lubricated value, some say to install dry, and some name a specific compound. When the manual is silent, ask before guessing. A calibrated wrench from our DIY torque wrench guide only helps if the number you dial in matches the thread condition.
Threadlocker brings its own procedure. Loctite says to start with clean, oil-free threads, place a few drops where the nut will engage, and allow 24 hours for a full cure. Blue grades then come apart with normal tools, while red needs local heat first.
Salt, Heat and West Michigan Hardware
Winter brine is the reason anti-seize earns so much shelf space around Grand Rapids. Salt spray reaches exhaust flange studs, hitch pins, skid plate bolts and wheel-adjacent hardware, and freeze-thaw cycles keep feeding the corrosion. A thin film on reassembly means the next person with a wrench is not fighting a rusted lump.
If a bolt is already frozen, the compound question comes second. Free it with one of the products in our penetrating oil buying guide, clean the threads, and only then choose between locking and lubricating. Our anti-seize compound roundup covers more formulas for hot and salty spots.

Some fasteners want neither product. An oil drain plug relies on its washer and correct torque, so keep both compounds off it, and if a plug keeps leaking, let us check it during an oil change in Creston. What goes inside the engine is a different category entirely: our synthetic oil buying guide and fuel system cleaner picks cover those.
Threadlocker vs Anti-Seize: When to Hand the Job Over
Brake and suspension fasteners are where the stakes jump. Caliper bracket bolts, control arm bolts and steering parts often come with a specific compound or a pre-applied patch, and some are meant to be replaced rather than reused. Never let anti-seize or any grease reach brake pads or rotor faces.

Exhaust work is the other common trouble spot. If a manifold stud snaps or a flange bolt will not budge, our exhaust repair in Grand Rapids can extract and replace the hardware. For everything else, the deeper lists in our threadlocker for cars guide help match a strength to the job, and the threadlocker vs anti seize rule stays simple: lock what shakes, lubricate what seizes.
More Buying Guides
Frequently Asked Questions
What is the main difference in threadlocker vs anti seize?
Threadlocker cures between the threads to stop a fastener from loosening under vibration. Anti-seize stays a paste and keeps threads from rusting, galling or seizing so the part comes apart later. One holds, the other releases.
Can I put threadlocker and anti-seize on the same bolt?
Not on the same threads. The grease in anti-seize can stop threadlocker from curing and still lets the bolt turn easily, so neither does its job. Use the one the vehicle maker calls for.
Does anti-seize change the torque spec?
It can. Lubricated threads reach more clamping force at the same wrench reading, so a dry torque figure applied to coated threads may over-stretch the bolt. Follow the vehicle maker’s instructions for lubricated or dry installation.
How do I remove a bolt that has blue threadlocker on it?
Loctite says blue threadlocker comes apart with normal hand tools. Use a well-fitting socket and steady pressure. Red threadlocker is different: Loctite says it needs local heat before the bolt will turn.
Not sure which compound a brake, suspension or exhaust bolt needs? Talk it through with 456 AutoFix at 616-279-3832, Monday to Friday from 8am to 5pm, or send us a request through the contact page.
Busy during shop hours? Our after-hours drop-off lets you leave the keys whenever it suits you, and you will find us at 456 Carrier St NE, Grand Rapids.
