As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
Pickups work their front suspension harder than most cars, with heavier engines, bigger tires and loads in the bed. Finding the best control arms for trucks starts with your exact model, then the corner that is worn, and finally whether the truck sits at factory height or on a lift.
This guide covers the Tundra, Titan, Colorado and Canyon, Ranger and Frontier; Silverado, F-150 and Tacoma owners have dedicated guides linked below. For a look at the companies behind these parts, start with our rundown of control arm brands worth knowing.
Quick answer
Which control arms should a pickup owner buy?
At stock height, buy an OE-style arm with the ball joint installed for your exact truck and corner, such as the MOOG RK621307 for a Tundra or the Metrix upper for a 2019-2023 Ranger. On a lifted Tundra, the Rough Country forged uppers correct the ball joint angle. Always confirm year, side and drivetrain on Amazon.
Our Quick Picks
Three listings that cover the most common truck jobs: a stock upper, a lift upper and a midsize replacement. Confirm year, side and drivetrain on Amazon first.

MOOG RK621307
An OE-style MOOG upper arm for a Tundra at factory height.

Rough Country Tundra Upper Arms
Upper arms drawn for a Tundra running a 3.5 inch lift.

Metrix Premium Ranger Upper Arm
A pre-greased upper arm for the current-shape Ranger.
Upper Arm, Lower Arm and What Wears Out First
Every truck in this guide uses a short-long arm front end: a shorter upper arm and a longer lower arm at each front wheel, with the coilover or spring between them. The lower arm carries most of the weight, so its bushings and ball joint often go first. The upper arm sees lighter loads, but its ball joint is usually built in, so a loose joint means a new arm.
Before you shop, pin down four details from the listing title and the fit checker:
- Position: upper or lower, driver or passenger side. Most listings are one arm for one corner.
- Generation: a 2015 Colorado and a 2012 Colorado share a name and nothing else underneath.
- Drivetrain and knuckle: 2WD and 4WD trucks can use different lowers.
- Grease fitting: a greasable joint can be serviced; a sealed one cannot.
Not sure the arm is the problem? Clunks, wandering and uneven tire wear point to a tired arm on almost any vehicle, and our guide to signs a control arm is failing walks through each one, even though it was written with Audis in mind.
Factory Height or Lifted: Two Different Shopping Lists
A truck at factory height needs an arm that copies the original. OE-style replacements come with rubber bushings and the ball joint already pressed in.
A lift changes that. Raising the front tilts the upper ball joint toward the edge of its travel, and the alignment shop can run out of caster or camber adjustment. Lift uppers bring the joint back into its working range and are sold by lift height. A small leveling kit can often keep the factory uppers, so buy lift arms when the alignment says you need them.
Best Control Arms for Trucks: Six Listings by Model
Each listing below names specific model years, and the single-arm listings name a side and position. Enter your truck in Amazon’s fit checker and read the notes under the result before you order.
1. MOOG RK621307: Front Left Upper Control Arm and Ball Joint for 2007-2019 Tundra

- Front left (driver side) upper position
- Listed for 2007-2019 Tundra and 2008-2019 Sequoia
- Ball joint comes installed in the arm
- Matching right side sold as RK621308
The MOOG RK621307 is a complete front left upper control arm for the second-generation Toyota Tundra, sold with its ball joint already in place. The listing gives the fit as the 2007-2019 Tundra and the 2008-2019 Sequoia, which share this front suspension design. It replaces the original driver side upper arm on a truck that still sits at factory height.
On these trucks the upper ball joint is built into the arm, so a joint with play, or a boot that has split and let water in, is usually the reason to change the whole arm. Buying the assembly also renews the two inner bushings, which harden with age and salt exposure. MOOG describes the arm as a part meant to hold the front geometry where it belongs, helping steering response and keeping the truck stable on the highway. The passenger side arm is a separate listing, the RK621308, so a full upper job takes two orders.
This is an OE-style replacement, not a lift part. If your Tundra wears a lift of around 3 inches or more, a lift-specific upper arm is the better match. Run your truck through Amazon’s fit checker, confirm the year and cab details it asks for, and book an alignment once the new arm is on.
2. Rough Country Forged Aluminum Upper Control Arms: Pair for 2007-2021 Tundra with 3.5 Inch Lift

- Left and right upper arms, sold as a pair
- Forged aluminum construction
- Greasable POM ball joints
- Bolt-on install, limited lifetime warranty
These Rough Country upper control arms are a left and right pair made for the 2007-2021 Toyota Tundra running a 3.5 inch lift. The arms are forged from aluminum in one piece, so there are no welded joints in the arm itself. They are among the best upper control arms for lifted trucks in this size class when the factory arms have run out of adjustment after a lift.
The ball joints use a POM (polyoxymethylene) ball, which Rough Country says reduces friction and gives more range of motion than the factory joint. That extra movement lets the front wheel travel through its full range without the joint binding at full droop, a common complaint on raised trucks. The joints are fully greasable, which is useful on a truck that sees salted roads all winter.
Rough Country describes the install as 100 percent bolt-on with no cutting or drilling, and quotes about 3 to 4 hours of work. They are covered by the company’s limited lifetime warranty. These are the wrong choice for a stock-height Tundra, where a factory-style arm is simpler, and they do not fit the 2022 and later truck, which has its own Rough Country listing. Plan on an alignment right after installation.
View Rough Country Tundra Upper Arms on Amazon

3. MOOG RK620650: Front Left Upper Control Arm and Ball Joint for 2004-2019 Nissan Titan

- Front left (driver side) upper position
- Listed for 2004-2019 Titan
- Also fits listed Armada and QX56 years
- Ball joint pre-installed in the arm
The MOOG RK620650 is a front left upper control arm and ball joint assembly for the Nissan Titan. The listing names the 2004-2019 Titan, along with the 2004 Pathfinder Armada, the 2005-2015 Armada and the 2004-2013 Infiniti QX56, which all share this front suspension layout. It is a direct replacement for the driver side upper arm on a truck at factory height.
Titan owners usually reach for a new upper arm when the ball joint develops play or the bushings start to knock over expansion joints. Because the joint is part of the arm, replacing the assembly is quicker than trying to service the joint alone. MOOG presents the arm as a way to restore steering response and keep the truck stable, which mostly comes down to fresh bushings and a tight joint. The matching passenger side arm, RK620649, is sold under its own listing.
The Titan years in the listing run from 2004 to 2019, which spans the first generation and the early years of the redesigned truck, so the fit checker is the place to confirm your exact Titan and trim. It is also not designed for a lifted truck. Enter your VIN details in Amazon’s fit checker, order the side you need, and plan an alignment after the swap.
4. TRQ Front Left Lower Control Arm: Steel Arm with Ball Joint for 2015-2022 Colorado and Canyon

- Front left (driver side) lower position
- Listed for 2015-2022 Colorado and Canyon
- Steel arm with ball joint installed
- Limited lifetime warranty per listing
The TRQ front left lower control arm is a steel replacement arm with the ball joint already installed, listed for the 2015-2022 Chevrolet Colorado and the 2015-2022 GMC Canyon. The lower arm carries most of the truck’s weight through the coilover, so its ball joint and rear bushing are often the first parts to wear on a midsize pickup that tows or hauls.
TRQ prints a long list of reference numbers on the listing, including RK623445, 527-035 and CMS501239, which helps you cross-check the part against the arm you are removing or against a parts catalog. The arm arrives pre-assembled, so there is no ball joint to press and no bushings to install on the bench. TRQ also points buyers to its library of installation videos, which can help if you are planning the job at home.
The listing states a limited lifetime warranty against defects in materials and workmanship, with normal wear excluded. This is a driver side arm only, so a pair of new lowers means ordering the passenger side separately. It does not fit the 2004-2012 Colorado or the redesigned 2023 and later truck. TRQ itself recommends checking Amazon’s confirmed fit result, and an alignment should follow the install.
View TRQ Colorado Lower Arm on Amazon

5. Metrix Premium Control Arm with Ball Joint: Front Right Upper for 2019-2023 Ford Ranger

- Front right (passenger side) upper position
- Listed for 2019-2023 Ford Ranger
- Pre-greased ball joint, sheet metal arm
- 3 year / 36,000 mile limited warranty
This Metrix Premium arm is a front right upper control arm with its ball joint installed, listed for the 2019-2023 Ford Ranger. It replaces the passenger side upper arm on the midsize Ranger that returned to the US market for 2019. Metrix gives the OE interchange number as KB3Z3084A and the aftermarket cross-reference as 526-670, so you can match it against the arm on your truck.
The listing describes the arm as sheet metal, like the factory part, and the ball joint as pre-greased for a longer service life. A retaining ring comes in the box, and the package holds one arm. Metrix says its parts are made in Europe in IATF 16949 and ISO 9001 certified plants, and it backs them with a 3 year or 36,000 mile limited warranty from the date of installation.
On the Ranger, the upper ball joint is part of the arm, so a worn joint or torn boot usually means replacing the whole assembly. This listing covers the right side only, so a driver side arm is a separate purchase. It is meant for a truck at factory height, not one with a large lift. Check the fit result on Amazon, and have the alignment set once the arm is in.
View Metrix Premium Ranger Upper Arm on Amazon
6. Detroit Axle Front Upper Left Control Arm and Ball Joint: Driver Side for 2005-2025 Nissan Frontier

- Front left (driver side) upper position
- Listed for 2005-2025 Frontier
- Also fits listed Pathfinder and Xterra years
- 10-year warranty per listing
The Detroit Axle front upper left control arm is a driver side arm and ball joint assembly for the Nissan Frontier. The listing names the 2005-2025 Frontier, the 2005-2012 Pathfinder and the 2005-2015 Xterra, which share this upper arm. The Frontier kept the same basic front suspension for a long time, so one part number covers a wide spread of model years.
The kit contains one arm with the ball joint fitted, ready to bolt in where the original came out. Detroit Axle states that its suspension line is tested for impact, wear and fatigue. Its warranty page lists control arms among the parts covered for 10 years, starting from the delivery date of the original purchase. That coverage is practical for a truck you plan to keep through many more Michigan winters.
This listing is the driver side only, so the passenger side arm is ordered separately. It is an OE-style replacement for a Frontier at factory height, not a lift arm, and it is not listed for the 1998-2004 truck. Trims and options can still affect fit, so put your exact truck into Amazon’s fit checker before buying, and book an alignment after the arm is installed.
View Detroit Axle Frontier Upper Arm on Amazon
Which Listing Matches Your Truck
This table repeats each listing’s stated fit. Trim and suspension options can still change the part.
| Truck and years | Ride height | Position | Listing to check |
|---|---|---|---|
| Tundra 2007-2019 | Stock | Front left upper | MOOG RK621307 |
| Tundra 2007-2021 | Lifted 3.5 inch | Front upper pair | Rough Country forged uppers |
| Titan 2004-2019 | Stock | Front left upper | MOOG RK620650 |
| Colorado and Canyon 2015-2022 | Stock | Front left lower | TRQ lower arm |
| Ranger 2019-2023 | Stock | Front right upper | Metrix Premium upper |
| Frontier 2005-2025 | Stock | Front left upper | Detroit Axle upper |
The opposite side always has its own part number, and the best control arms for trucks are bought as matching brands when both corners are done.

Salt, Potholes and Pickup Front Ends
Trucks in West Michigan spend months on brine-soaked roads, and the spring thaw opens deep potholes. Salt water gets past a split ball joint boot and ruins the grease, while cold and age crack the rubber bushings.
A quick look at the boots and bushings each time the truck is on a lift catches most of this early. If your arms have grease fittings, a few pumps in the fall pushes out trapped moisture before winter starts.

Worn shocks make every pothole hit harder, so check them while the front end is apart; our guide to shocks and struts for everyday driving covers how to spot tired ones.
Installing, Aligning and When to Bring It In
Swapping a complete arm is easier than pressing in a ball joint, but it is still safety work: secure stands, a supported coilover and factory torque on every bolt. Tighten the bushing bolts with the suspension at ride height so the rubber is not preloaded in a twisted position.

Plan an alignment the same week, because new arms move caster and camber. The Car Care Council’s vehicle systems overview lists uneven tire wear, shaking and pulling to one side as signs of an alignment problem. Whichever of the best control arms for trucks you pick, rusted bolts can stretch a Saturday job into a week, and our suspension repair team in Grand Rapids can inspect the front end and fit the parts. Steering and suspension is one of the areas our owner, Hendrick Hoffman, is ASE and State of Michigan certified in.
More Buying Guides
Frequently Asked Questions
Do I need upper control arms for a leveling kit?
Often not. Many trucks with a small leveling kit still align within spec on the factory uppers. Lift-specific uppers make sense when the alignment cannot reach the caster or camber range, or when the upper ball joint is close to binding.
Should truck control arms be replaced in pairs?
When both sides have the same miles and similar wear, a pair keeps the front end even. If one arm was bent by a pothole and the other checks tight, replacing only the damaged side is reasonable.
Are aftermarket lift arms stronger than factory arms?
Not necessarily. Their main job is to correct ball joint angle and alignment range on a raised truck. On a stock-height truck, an OE-style arm is the simpler match.
Does a control arm listing fit both sides of the truck?
Usually not. Left and right arms are mirror images with their own part numbers, so check the side in the listing title. Pair listings, such as the Rough Country uppers, include both sides.
Pickup wandering on the highway or knocking over every railroad crossing? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a front end inspection through our contact page.
Working a shift that runs past five? Bring the truck to 456 Carrier St NE after hours, use the drop-off, and we will take a look once the shop opens.
