456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Outback, Forester, Crosstrek or WRX? Finding the Best Shocks and Struts for Subaru

best shocks and struts for subaru: snowy road through a foggy forest

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

Subarus tend to stay in the family for a long time, and somewhere past the 100,000-mile mark the original dampers start letting the body float and wallow. Picking the best shocks and struts for Subaru models starts with the exact car in your driveway, because an Outback, a Forester, a Crosstrek, an Impreza and a WRX each use their own parts, and the parts change again between generations.

Below are six specific Amazon listings, each tied to the Subaru it names. Not sure the old ones are worn? Read our guide on how to tell if struts are bad first.

Quick answer

What shocks and struts should a Subaru get?

An Outback, Forester or Crosstrek driven every day is usually happiest on an OE-style strut such as KYB Excel-G, Bilstein B4 or Monroe OESpectrum. A complete assembly from Monroe or Unity skips the spring compressor, while a WRX owner after firmer control can look at Bilstein B6. Always match year, trim and corner.

Our Quick Picks

Three quick picks: an OE-grade Excel-G strut for the Outback, a ready-to-bolt-in assembly for the older Impreza sedan and a firmer monotube strut for the WRX. All six listings are reviewed below.

KYB Excel-G 339225 product photo
Outback pick

KYB Excel-G 339225

Bare gas strut · Subaru Outback

An OE-grade twin-tube strut that aims to bring back the factory ride.

SuitsOutback owners who want the original feel
View on Amazon →
Unity 11198 product photo
Impreza pick

Unity 11198

Complete assembly · 2004-2007 Impreza sedan

A preassembled front strut for the second-generation Impreza sedan.

SuitsOwners keeping an older Impreza on the road
View on Amazon →
Bilstein B6 35-249467 product photo
WRX pick

Bilstein B6 35-249467

Front left monotube strut · 2015-2017 WRX / STI

A firmer monotube strut for drivers who want tighter body control.

SuitsWRX drivers who want firmer handling
View on Amazon →

How Subaru Suspension Layouts Differ by Model

Every model in this guide uses MacPherson struts up front, where the strut holds the coil spring and acts as the upper locating point for the wheel. Most also use a strut with its own spring at each rear corner, so a Subaru often needs four struts rather than two struts and two shocks.

  • Outback and Legacy: close relatives, but the Outback rides higher on its own struts.
  • Crosstrek: built on the Impreza, yet lifted, so the two do not share struts.
  • WRX: its own firmer setup, and the STI differs again.

Generation breaks are the trap. A 2013 and a 2014 Forester are different generations, and the Outback changed between 2014 and 2015, so treat each listing’s year range as a hard limit.

Comfort or Firm: Matching Damping to Your Subaru

For most owners, the best shocks and struts for Subaru commuters are OE-style twin-tube parts such as KYB Excel-G, Monroe OESpectrum and Bilstein B4, which aim to restore the factory ride rather than change it. They suit a family wagon or a crossover that spends weekends on gravel.

A firmer monotube damper such as Bilstein B6 is aimed at drivers who want tighter body control, which is why it shows up on WRX shopping lists. It will feel busier over broken pavement. Bilstein covers both the B4 and B6 lines under its limited lifetime warranty for North American purchases, so the choice comes down to ride feel rather than coverage.

Before ordering, run your year, trim, body style and corner through the Amazon fit checker, since no listing fits every version of its model.

Best Shocks and Struts for Subaru: Six Listings Matched to Model

Each pick below is one Amazon US listing for a named Subaru. If your year or corner is different, look for the matching part number within the same brand line instead of forcing a near fit.

1. KYB Excel-G 339225: OE-Grade Gas Strut for the Subaru Outback

KYB Excel-G 339225 product photo
Key features
  • Calibrated for the Subaru Outback
  • Replaces Subaru 20310AJ05A and 20310AJ05B
  • Seamless cylinder with Teflon-coated piston band
  • Triple chrome-plated piston rod

KYB lists the Excel-G line as its leading original equipment replacement choice for Asian cars, aimed at drivers who want the car to feel as it did new. This listing is part number 339225, and its title says it replaces the Subaru numbers 20310AJ05A and 20310AJ05B, along with the cross-reference number 72687. The feature list states it is calibrated for the Subaru Outback, though the title gives no model years.

Inside, KYB uses a seamless working cylinder with a Teflon-coated piston band for a tight seal, a triple chrome-plated rod and multi-lip oil seals meant to slow wear. A sintered iron rod guide is there to help the strut hold correct wheel alignment as it ages. Those details point to a long-lived commuter part rather than a firmer sport damper, which suits a wagon that carries family and gear.

Because this is a bare strut, your coil spring, upper mount and boot transfer from the old unit, so you will need a spring compressor or a shop that has one. The surest fit check is the Subaru number on your existing strut, then the Amazon fit checker with your year, trim and position. Buy matching units for the axle so both sides wear evenly.

View KYB Excel-G 339225 on Amazon

2. Bilstein B4 22-278470: OE Replacement Front Right Twin-Tube Strut for 2014-2018 Subaru Forester

Bilstein B4 22-278470 product photo
Key features
  • Front right strut for the 2014-2018 Forester
  • Twin-tube OE replacement design
  • Constant damping under any load
  • Bilstein gas-pressure technology

The fourth-generation Forester, sold from 2014 to 2018, is now old enough that many examples are on their original front struts. This Bilstein listing, part number 22-278470, is a B4 OE Replacement twin-tube strut, and its title names that Forester range and the front right corner. The B4 series is Bilstein’s line for restoring the stock ride rather than stiffening it.

The listing highlights high power reserves, damping that stays constant under any load and gas-pressure technology aimed at traction and precise handling. For a crossover that carries a full cargo area one weekend and nothing the next, steady damping across loads is the useful part of that list. Bilstein backs the B4 range with a limited lifetime warranty on North American purchases.

This part covers one corner only, so the left front has its own Bilstein number and you should order both for an even front axle. As a bare strut, it reuses your spring and upper mount, which means compressing the spring safely during the swap. Check year, trim and position in the Amazon fit checker, and do not assume it carries over to the 2019 Forester, which moved to a new platform.

View Bilstein B4 22-278470 on Amazon

winter road with a warning sign

3. Monroe OESpectrum 73071: Twin-Tube Suspension Strut for 2013-2017 Subaru Crosstrek

Monroe OESpectrum 73071 product photo
Key features
  • Fits 2013-2015 XV Crosstrek and 2016-2017 Crosstrek
  • Twin Technology Active Control System
  • All-weather fluid for temperature extremes
  • PTFE-banded piston and nitrogen gas charge

The first-generation Crosstrek was sold as the XV Crosstrek from 2013 to 2015 and as the Crosstrek for 2016 and 2017, and this Monroe listing names both. Part number 73071 is an OESpectrum strut, Monroe’s OE-style line for drivers who want a quiet, controlled ride rather than a sporty one. The title does not name a corner, so check the fit notes for front or rear and for side.

Monroe describes a Twin Technology Active Control System meant to keep control while isolating noise and harshness from impacts. Rod displaced valving is tuned to each vehicle, and the all-weather fluid includes additives for temperature extremes, which matters for a car that sits outside through a Michigan January. A PTFE-banded piston, a nitrogen gas charge, a chrome-plated piston and a bronze-reinforced rod guide round out the build.

This is a bare strut, so the spring and mount from the old unit carry over, and the protective boot and jounce bumper are sold separately. That makes it a good time to replace a cracked boot rather than reuse it. Confirm the year, trim and position on Amazon before buying, and order in pairs for the axle.

View Monroe OESpectrum 73071 on Amazon

4. Monroe Quick-Strut 172695: Complete Strut and Coil Spring Assembly for 2009-2013 Subaru Forester

Monroe Quick-Strut 172695 product photo
Key features
  • Fits the 2009-2013 Forester
  • Preassembled strut, coil spring and upper mount
  • No spring compressor needed
  • Protective coating tested against salt spray

The third-generation Forester, built for the 2009 to 2013 model years, is now at the age where struts, springs and mounts are all tired at once. This Monroe Quick-Strut listing, part number 172695, names that Forester range and arrives as a complete unit: strut, application-specific coil spring and upper mount already assembled. The title does not give the corner, so read the fit notes for position before ordering.

The main benefit is that no spring compressor is needed, which removes the riskiest step of a strut job at home. Monroe states the spring is calibrated to the OE design to restore ride height, and the premium upper mount is meant to keep steering smooth and cut noise and memory steer. A protective coating that has been salt spray tested helps on a car that sees winter brine.

A complete assembly also gets rid of a sagging spring or a cracked mount bushing that a bare strut would reuse. It costs more than a bare strut, but on a high-mileage Forester the extra parts are often due anyway. Run your year, engine and trim through the Amazon Confirmed Fit bar, and replace both sides of the axle together.

View Monroe Quick-Strut 172695 on Amazon

red car on a mountain curve

5. Unity Automotive 11198: Front Right Complete Strut Assembly for 2004-2007 Subaru Impreza Sedan

Unity 11198 product photo
Key features
  • Front right corner, 2004-2007 Impreza sedan
  • Includes top mount, bearing plate and coil spring
  • Bumper and insulators preassembled
  • No specialty tools needed

Plenty of second-generation Imprezas are still in daily use, and most have long since worn through their original front struts. This Unity Automotive listing, part number 11198, is a front right complete strut assembly for the 2004 to 2007 Subaru Impreza sedan. The listing states plainly that it fits the sedan only, so a wagon owner needs a different part.

The assembly comes with the top mount, bearing plate, bumper, insulators and coil spring already fitted to the strut. Unity describes it as an original-equipment-style design meant to fit directly and restore factory ride height. Because every component is new, you avoid reusing a rusted spring seat or a dried-out mount, and the job needs no spring compressor.

Unity recommends replacing both sides for best results, so plan on buying the left front unit as well. An older car also deserves a look at the sway bar links and control arm bushings while the strut is out, since those wear on the same schedule. Confirm body style, year and trim in the Amazon fit checker, then book an alignment once both struts are in.

View Unity 11198 on Amazon

6. Bilstein B6 35-249467: Front Left Monotube Performance Strut for 2015-2017 Subaru WRX / STI

Bilstein B6 35-249467 product photo
Key features
  • Front left strut for the 2015-2017 WRX / STI
  • Monotube gas-pressure design
  • Works with the series spring
  • Fine-tuned in Bilstein road testing

The WRX is the Subaru most likely to be driven hard, and its owners often want more control than an OE-style strut offers. This Bilstein listing, part number 35-249467, is a B6 monotube strut, and its title names the 2015 to 2017 Subaru WRX and STI and the front left corner. Check the fit notes carefully, since the WRX and STI can use different front struts within those years.

Bilstein describes the B6 as delivering higher power reserves, better grip and improved lane stability in everyday and extreme driving. The listing also says the series spring can be used, so the strut is meant to bolt in with the factory spring rather than a lowering kit. Bilstein states each application is fine-tuned in its own road testing.

Expect a firmer, more connected ride than the factory dampers, which some drivers love and others find busy on rough roads. As a bare strut, it reuses your spring and mount, so a spring compressor or a shop is part of the plan. Order the matching right front part for an even axle, confirm year, trim and position on Amazon, and book an alignment afterward.

View Bilstein B6 35-249467 on Amazon

Six Subaru Listings Side by Side

The type column matters most, because it decides whether the job needs a spring compressor and whether you also get a fresh mount and spring.

ListingSubaru and positionTypeKeep in mind
KYB Excel-G 339225Outback, per listingBare strutNo years in the title; compare the Subaru numbers it replaces
Bilstein B4 22-2784702014-2018 Forester, front rightBare strutLeft front is a separate part
Monroe OESpectrum 730712013-2017 CrosstrekBare strutConfirm the corner in the fit notes
Monroe Quick-Strut 1726952009-2013 ForesterComplete assemblyConfirm the corner in the fit notes
Unity 111982004-2007 Impreza sedan, front rightComplete assemblySedan only, not the wagon
Bilstein B6 35-2494672015-2017 WRX / STI, front leftBare monotube strutFirmer feel; right side sold separately
Subaru shock and strut listings compared by model, position and type

Whatever you buy, replace dampers in axle pairs, because a new strut beside a tired one makes the car lean and brake unevenly. On a high-mileage Subaru, a complete assembly also replaces a sagging spring and worn mount.

driver's hands on a steering wheel

Have a second car from another brand? If the household has a non-Subaru too, see the best shocks and struts for daily drivers.

Road Salt, Frost Heaves and Subaru Struts in West Michigan

All-wheel drive does nothing to protect struts from a Michigan winter. Brine and salt attack the spring seats, strut bodies and knuckle bolts, and each spring the frost heaves and potholes finish off tired dampers. That is why the best shocks and struts for Subaru owners around Grand Rapids are often complete assemblies with fresh hardware.

Tires often show the problem before the ride does. Gabriel’s answers on shock and strut wear list cupped tires as a common sign of worn ride control parts, so run a hand over the tread when you check pressures. A squeak or groan over speed bumps is a different clue, and our guide on why a car squeaks when going over bumps helps you separate dry bushings from a failing strut.

shock absorber rod close-up

After a hard hit, look for a low corner, a new pull or oil running down a strut, and check our list of pothole damage signs.

Driveway Job or Shop Job?

A complete assembly on a Forester or an Impreza is a fair weekend job for someone with jack stands, a torque wrench and penetrating oil. A bare strut is more serious. The spring has to be held compressed while the top nut comes off, and a spring that slips can cause real injury, so read our guide to choosing a coil spring compressor first.

Plan on a wheel alignment after any front strut swap, because the strut sets the top of the wheel and its removal can shift camber and toe. Rusted knuckle bolts are the other reason many salt-belt owners hand the work over. A deep knock usually points elsewhere; see our guide to a clunking noise over bumps.

snowy park path

Our suspension repair in Grand Rapids handles strut and shock replacement, mounts and the connected steering parts on Subarus and other imports. Steering and suspension is one of the areas where head mechanic Hendrick Hoffman is certified by both ASE and the State of Michigan.

Frequently Asked Questions

Are KYB or Bilstein struts better for a Subaru Forester?

Both make OE-style replacements. The Bilstein B4 22-278470 covers the front right of a 2014 to 2018 Forester, while an older 2009 to 2013 Forester can take a complete Monroe Quick-Strut. Pick by generation first, then by the ride you prefer.

Should I replace all four struts on my Subaru at once?

Pairs are the minimum, so both fronts or both rears together. If the car has high mileage and all four are original, doing the whole car at once keeps the ride balanced and saves a second alignment.

Does a Subaru need an alignment after new struts?

After front struts, yes. Taking the strut off the knuckle can change camber and toe, and an all-wheel-drive car that is out of alignment wears its tires unevenly.

Will Bilstein B6 struts work with stock WRX springs?

The listing for the Bilstein B6 35-249467 says the series spring can be used, so a stock 2015 to 2017 WRX does not need new springs to fit it. Expect a firmer ride than the factory dampers.

Is your Subaru floating over dips, leaning hard in turns or thumping over rough pavement? Ring 456 AutoFix at 616-279-3832, Monday to Friday from 8am to 5pm, or book a suspension check through our contact page.

Can’t get away during the work day? Drive the Subaru over to 456 Carrier St NE in Grand Rapids after closing and leave it with our after-hours drop-off.